diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h
index fe904846e3582..bdf86392c97f5 100644
--- a/Marlin/src/core/boards.h
+++ b/Marlin/src/core/boards.h
@@ -221,7 +221,7 @@
#define BOARD_5DPRINT 1707 // 5DPrint D8 Driver Board
//
-// LPC1768 ARM Cortex M3
+// LPC1768 ARM Cortex-M3
//
#define BOARD_RAMPS_14_RE_ARM_EFB 2000 // Re-ARM with RAMPS 1.4 (Power outputs: Hotend, Fan, Bed)
@@ -242,7 +242,7 @@
#define BOARD_EMOTRONIC 2015 // eMotion-Tech eMotronic
//
-// LPC1769 ARM Cortex M3
+// LPC1769 ARM Cortex-M3
//
#define BOARD_MKS_SGEN 2500 // MKS-SGen
@@ -259,7 +259,7 @@
#define BOARD_FLY_CDY 2511 // FLYmaker FLY CDY
//
-// SAM3X8E ARM Cortex M3
+// SAM3X8E ARM Cortex-M3
//
#define BOARD_DUE3DOM 3000 // DUE3DOM for Arduino DUE
@@ -292,185 +292,195 @@
#define BOARD_KRATOS32 3027 // K.3D Kratos32 (Arduino Due Shield)
//
-// SAM3X8C ARM Cortex M3
+// SAM3X8C ARM Cortex-M3
//
#define BOARD_PRINTRBOARD_G2 3100 // Printrboard G2
#define BOARD_ADSK 3101 // Arduino DUE Shield Kit (ADSK)
+//
+// STM32 ARM Cortex-M0+
+//
+
+#define BOARD_BTT_EBB42_V1_1 4000 // BigTreeTech EBB42 V1.1 (STM32G0B1CB)
+#define BOARD_BTT_SKR_MINI_E3_V3_0 4001 // BigTreeTech SKR Mini E3 V3.0 (STM32G0B1RE)
+#define BOARD_BTT_MANTA_E3_EZ_V1_0 4002 // BigTreeTech Manta E3 EZ V1.0 (STM32G0B1RE)
+#define BOARD_BTT_MANTA_M4P_V1_0 4003 // BigTreeTech Manta M4P V1.0 (STM32G0B1RE)
+#define BOARD_BTT_MANTA_M5P_V1_0 4004 // BigTreeTech Manta M5P V1.0 (STM32G0B1RE)
+#define BOARD_BTT_MANTA_M8P_V1_0 4005 // BigTreeTech Manta M8P V1.0 (STM32G0B1VE)
+#define BOARD_BTT_MANTA_M8P_V1_1 4006 // BigTreeTech Manta M8P V1.1 (STM32G0B1VE)
+
//
// STM32 ARM Cortex-M3
//
-#define BOARD_MALYAN_M200_V2 4000 // STM32F070CB controller
-#define BOARD_MALYAN_M300 4001 // STM32F070-based delta
-#define BOARD_STM32F103RE 4002 // STM32F103RE Libmaple-based STM32F1 controller
-#define BOARD_MALYAN_M200 4003 // STM32C8 Libmaple-based STM32F1 controller
-#define BOARD_STM3R_MINI 4004 // STM32F103RE Libmaple-based STM32F1 controller
-#define BOARD_GTM32_PRO_VB 4005 // STM32F103VE controller
-#define BOARD_GTM32_MINI 4006 // STM32F103VE controller
-#define BOARD_GTM32_MINI_A30 4007 // STM32F103VE controller
-#define BOARD_GTM32_REV_B 4008 // STM32F103VE controller
-#define BOARD_MORPHEUS 4009 // STM32F103C8 / STM32F103CB Libmaple-based STM32F1 controller
-#define BOARD_CHITU3D 4010 // Chitu3D (STM32F103RE)
-#define BOARD_MKS_ROBIN 4011 // MKS Robin (STM32F103ZE)
-#define BOARD_MKS_ROBIN_MINI 4012 // MKS Robin Mini (STM32F103VE)
-#define BOARD_MKS_ROBIN_NANO 4013 // MKS Robin Nano (STM32F103VE)
-#define BOARD_MKS_ROBIN_NANO_V2 4014 // MKS Robin Nano V2 (STM32F103VE)
-#define BOARD_MKS_ROBIN_LITE 4015 // MKS Robin Lite/Lite2 (STM32F103RC)
-#define BOARD_MKS_ROBIN_LITE3 4016 // MKS Robin Lite3 (STM32F103RC)
-#define BOARD_MKS_ROBIN_PRO 4017 // MKS Robin Pro (STM32F103ZE)
-#define BOARD_MKS_ROBIN_E3 4018 // MKS Robin E3 (STM32F103RC)
-#define BOARD_MKS_ROBIN_E3_V1_1 4019 // MKS Robin E3 V1.1 (STM32F103RC)
-#define BOARD_MKS_ROBIN_E3D 4020 // MKS Robin E3D (STM32F103RC)
-#define BOARD_MKS_ROBIN_E3D_V1_1 4021 // MKS Robin E3D V1.1 (STM32F103RC)
-#define BOARD_MKS_ROBIN_E3P 4022 // MKS Robin E3p (STM32F103VE)
-#define BOARD_BTT_EBB42_V1_1 4023 // BigTreeTech EBB42 V1.1 (STM32G0B1CB)
-#define BOARD_BTT_SKR_MINI_V1_1 4024 // BigTreeTech SKR Mini v1.1 (STM32F103RC)
-#define BOARD_BTT_SKR_MINI_E3_V1_0 4025 // BigTreeTech SKR Mini E3 (STM32F103RC)
-#define BOARD_BTT_SKR_MINI_E3_V1_2 4026 // BigTreeTech SKR Mini E3 V1.2 (STM32F103RC)
-#define BOARD_BTT_SKR_MINI_E3_V2_0 4027 // BigTreeTech SKR Mini E3 V2.0 (STM32F103RC / STM32F103RE)
-#define BOARD_BTT_SKR_MINI_E3_V3_0 4028 // BigTreeTech SKR Mini E3 V3.0 (STM32G0B1RE)
-#define BOARD_BTT_SKR_MINI_E3_V3_0_1 4029 // BigTreeTech SKR Mini E3 V3.0.1 (STM32F401RC)
-#define BOARD_BTT_SKR_MINI_MZ_V1_0 4030 // BigTreeTech SKR Mini MZ V1.0 (STM32F103RC)
-#define BOARD_BTT_SKR_E3_DIP 4031 // BigTreeTech SKR E3 DIP V1.0 (STM32F103RC / STM32F103RE)
-#define BOARD_BTT_SKR_CR6 4032 // BigTreeTech SKR CR6 v1.0 (STM32F103RE)
-#define BOARD_JGAURORA_A5S_A1 4033 // JGAurora A5S A1 (STM32F103ZE)
-#define BOARD_FYSETC_AIO_II 4034 // FYSETC AIO_II (STM32F103RC)
-#define BOARD_FYSETC_CHEETAH 4035 // FYSETC Cheetah (STM32F103RC)
-#define BOARD_FYSETC_CHEETAH_V12 4036 // FYSETC Cheetah V1.2 (STM32F103RC)
-#define BOARD_LONGER3D_LK 4037 // Longer3D LK1/2 - Alfawise U20/U20+/U30 (STM32F103VE)
-#define BOARD_CCROBOT_MEEB_3DP 4038 // ccrobot-online.com MEEB_3DP (STM32F103RC)
-#define BOARD_CHITU3D_V5 4039 // Chitu3D TronXY X5SA V5 Board (STM32F103ZE)
-#define BOARD_CHITU3D_V6 4040 // Chitu3D TronXY X5SA V6 Board (STM32F103ZE)
-#define BOARD_CHITU3D_V9 4041 // Chitu3D TronXY X5SA V9 Board (STM32F103ZE)
-#define BOARD_CREALITY_V4 4042 // Creality v4.x (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V422 4043 // Creality v4.2.2 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V423 4044 // Creality v4.2.3 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V425 4045 // Creality v4.2.5 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V427 4046 // Creality v4.2.7 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V4210 4047 // Creality v4.2.10 (STM32F103RC / STM32F103RE) as found in the CR-30
-#define BOARD_CREALITY_V431 4048 // Creality v4.3.1 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V431_A 4049 // Creality v4.3.1a (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V431_B 4050 // Creality v4.3.1b (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V431_C 4051 // Creality v4.3.1c (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V431_D 4052 // Creality v4.3.1d (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V452 4053 // Creality v4.5.2 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V453 4054 // Creality v4.5.3 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V521 4055 // Creality v5.2.1 (STM32F103VE) as found in the SV04
-#define BOARD_CREALITY_V24S1 4056 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7
-#define BOARD_CREALITY_V24S1_301 4057 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1
-#define BOARD_CREALITY_V25S1 4058 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro
-#define BOARD_TRIGORILLA_PRO 4059 // Trigorilla Pro (STM32F103ZE)
-#define BOARD_FLY_MINI 4060 // FLYmaker FLY MINI (STM32F103RC)
-#define BOARD_FLSUN_HISPEED 4061 // FLSUN HiSpeedV1 (STM32F103VE)
-#define BOARD_BEAST 4062 // STM32F103RE Libmaple-based controller
-#define BOARD_MINGDA_MPX_ARM_MINI 4063 // STM32F103ZE Mingda MD-16
-#define BOARD_GTM32_PRO_VD 4064 // STM32F103VE controller
-#define BOARD_ZONESTAR_ZM3E2 4065 // Zonestar ZM3E2 (STM32F103RC)
-#define BOARD_ZONESTAR_ZM3E4 4066 // Zonestar ZM3E4 V1 (STM32F103VC)
-#define BOARD_ZONESTAR_ZM3E4V2 4067 // Zonestar ZM3E4 V2 (STM32F103VC)
-#define BOARD_ERYONE_ERY32_MINI 4068 // Eryone Ery32 mini (STM32F103VE)
-#define BOARD_PANDA_PI_V29 4069 // Panda Pi V2.9 - Standalone (STM32F103RC)
+#define BOARD_MALYAN_M200_V2 5000 // STM32F070CB controller
+#define BOARD_MALYAN_M300 5001 // STM32F070-based delta
+#define BOARD_STM32F103RE 5002 // STM32F103RE Libmaple-based STM32F1 controller
+#define BOARD_MALYAN_M200 5003 // STM32C8 Libmaple-based STM32F1 controller
+#define BOARD_STM3R_MINI 5004 // STM32F103RE Libmaple-based STM32F1 controller
+#define BOARD_GTM32_PRO_VB 5005 // STM32F103VE controller
+#define BOARD_GTM32_MINI 5006 // STM32F103VE controller
+#define BOARD_GTM32_MINI_A30 5007 // STM32F103VE controller
+#define BOARD_GTM32_REV_B 5008 // STM32F103VE controller
+#define BOARD_MORPHEUS 5009 // STM32F103C8 / STM32F103CB Libmaple-based STM32F1 controller
+#define BOARD_CHITU3D 5010 // Chitu3D (STM32F103RE)
+#define BOARD_MKS_ROBIN 5011 // MKS Robin (STM32F103ZE)
+#define BOARD_MKS_ROBIN_MINI 5012 // MKS Robin Mini (STM32F103VE)
+#define BOARD_MKS_ROBIN_NANO 5013 // MKS Robin Nano (STM32F103VE)
+#define BOARD_MKS_ROBIN_NANO_V2 5014 // MKS Robin Nano V2 (STM32F103VE)
+#define BOARD_MKS_ROBIN_LITE 5015 // MKS Robin Lite/Lite2 (STM32F103RC)
+#define BOARD_MKS_ROBIN_LITE3 5016 // MKS Robin Lite3 (STM32F103RC)
+#define BOARD_MKS_ROBIN_PRO 5017 // MKS Robin Pro (STM32F103ZE)
+#define BOARD_MKS_ROBIN_E3 5018 // MKS Robin E3 (STM32F103RC)
+#define BOARD_MKS_ROBIN_E3_V1_1 5019 // MKS Robin E3 V1.1 (STM32F103RC)
+#define BOARD_MKS_ROBIN_E3D 5020 // MKS Robin E3D (STM32F103RC)
+#define BOARD_MKS_ROBIN_E3D_V1_1 5021 // MKS Robin E3D V1.1 (STM32F103RC)
+#define BOARD_MKS_ROBIN_E3P 5022 // MKS Robin E3P (STM32F103VE)
+#define BOARD_BTT_SKR_MINI_V1_1 5023 // BigTreeTech SKR Mini v1.1 (STM32F103RC)
+#define BOARD_BTT_SKR_MINI_E3_V1_0 5024 // BigTreeTech SKR Mini E3 (STM32F103RC)
+#define BOARD_BTT_SKR_MINI_E3_V1_2 5025 // BigTreeTech SKR Mini E3 V1.2 (STM32F103RC)
+#define BOARD_BTT_SKR_MINI_E3_V2_0 5026 // BigTreeTech SKR Mini E3 V2.0 (STM32F103RC / STM32F103RE)
+#define BOARD_BTT_SKR_MINI_MZ_V1_0 5027 // BigTreeTech SKR Mini MZ V1.0 (STM32F103RC)
+#define BOARD_BTT_SKR_E3_DIP 5028 // BigTreeTech SKR E3 DIP V1.0 (STM32F103RC / STM32F103RE)
+#define BOARD_BTT_SKR_CR6 5029 // BigTreeTech SKR CR6 v1.0 (STM32F103RE)
+#define BOARD_JGAURORA_A5S_A1 5030 // JGAurora A5S A1 (STM32F103ZE)
+#define BOARD_FYSETC_AIO_II 5031 // FYSETC AIO_II (STM32F103RC)
+#define BOARD_FYSETC_CHEETAH 5032 // FYSETC Cheetah (STM32F103RC)
+#define BOARD_FYSETC_CHEETAH_V12 5033 // FYSETC Cheetah V1.2 (STM32F103RC)
+#define BOARD_LONGER3D_LK 5034 // Longer3D LK1/2 - Alfawise U20/U20+/U30 (STM32F103VE)
+#define BOARD_CCROBOT_MEEB_3DP 5035 // ccrobot-online.com MEEB_3DP (STM32F103RC)
+#define BOARD_CHITU3D_V5 5036 // Chitu3D TronXY X5SA V5 Board (STM32F103ZE)
+#define BOARD_CHITU3D_V6 5037 // Chitu3D TronXY X5SA V6 Board (STM32F103ZE)
+#define BOARD_CHITU3D_V9 5038 // Chitu3D TronXY X5SA V9 Board (STM32F103ZE)
+#define BOARD_CREALITY_V4 5039 // Creality v4.x (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V422 5040 // Creality v4.2.2 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V423 5041 // Creality v4.2.3 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V425 5042 // Creality v4.2.5 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V427 5043 // Creality v4.2.7 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V4210 5044 // Creality v4.2.10 (STM32F103RC / STM32F103RE) as found in the CR-30
+#define BOARD_CREALITY_V431 5045 // Creality v4.3.1 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V431_A 5046 // Creality v4.3.1a (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V431_B 5047 // Creality v4.3.1b (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V431_C 5048 // Creality v4.3.1c (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V431_D 5049 // Creality v4.3.1d (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V452 5050 // Creality v4.5.2 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V453 5051 // Creality v4.5.3 (STM32F103RC / STM32F103RE)
+#define BOARD_CREALITY_V521 5052 // Creality v5.2.1 (STM32F103VE) as found in the SV04
+#define BOARD_CREALITY_V24S1 5053 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7
+#define BOARD_CREALITY_V24S1_301 5054 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1
+#define BOARD_CREALITY_V25S1 5055 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro
+#define BOARD_TRIGORILLA_PRO 5056 // Trigorilla Pro (STM32F103ZE)
+#define BOARD_FLY_MINI 5057 // FLYmaker FLY MINI (STM32F103RC)
+#define BOARD_FLSUN_HISPEED 5058 // FLSUN HiSpeedV1 (STM32F103VE)
+#define BOARD_BEAST 5059 // STM32F103RE Libmaple-based controller
+#define BOARD_MINGDA_MPX_ARM_MINI 5060 // STM32F103ZE Mingda MD-16
+#define BOARD_GTM32_PRO_VD 5061 // STM32F103VE controller
+#define BOARD_ZONESTAR_ZM3E2 5062 // Zonestar ZM3E2 (STM32F103RC)
+#define BOARD_ZONESTAR_ZM3E4 5063 // Zonestar ZM3E4 V1 (STM32F103VC)
+#define BOARD_ZONESTAR_ZM3E4V2 5064 // Zonestar ZM3E4 V2 (STM32F103VC)
+#define BOARD_ERYONE_ERY32_MINI 5065 // Eryone Ery32 mini (STM32F103VE)
+#define BOARD_PANDA_PI_V29 5066 // Panda Pi V2.9 - Standalone (STM32F103RC)
//
// ARM Cortex-M4F
//
-#define BOARD_TEENSY31_32 4100 // Teensy3.1 and Teensy3.2
-#define BOARD_TEENSY35_36 4101 // Teensy3.5 and Teensy3.6
+#define BOARD_TEENSY31_32 5100 // Teensy3.1 and Teensy3.2
+#define BOARD_TEENSY35_36 5101 // Teensy3.5 and Teensy3.6
//
// STM32 ARM Cortex-M4F
//
-#define BOARD_ARMED 4200 // Arm'ed STM32F4-based controller
-#define BOARD_RUMBA32_V1_0 4201 // RUMBA32 STM32F446VE based controller from Aus3D
-#define BOARD_RUMBA32_V1_1 4202 // RUMBA32 STM32F446VE based controller from Aus3D
-#define BOARD_RUMBA32_MKS 4203 // RUMBA32 STM32F446VE based controller from Makerbase
-#define BOARD_RUMBA32_BTT 4204 // RUMBA32 STM32F446VE based controller from BIGTREETECH
-#define BOARD_BLACK_STM32F407VE 4205 // BLACK_STM32F407VE
-#define BOARD_BLACK_STM32F407ZE 4206 // BLACK_STM32F407ZE
-#define BOARD_BTT_SKR_PRO_V1_1 4207 // BigTreeTech SKR Pro v1.1 (STM32F407ZG)
-#define BOARD_BTT_SKR_PRO_V1_2 4208 // BigTreeTech SKR Pro v1.2 (STM32F407ZG)
-#define BOARD_BTT_BTT002_V1_0 4209 // BigTreeTech BTT002 v1.0 (STM32F407VG)
-#define BOARD_BTT_E3_RRF 4210 // BigTreeTech E3 RRF (STM32F407VG)
-#define BOARD_BTT_SKR_V2_0_REV_A 4211 // BigTreeTech SKR v2.0 Rev A (STM32F407VG)
-#define BOARD_BTT_SKR_V2_0_REV_B 4212 // BigTreeTech SKR v2.0 Rev B (STM32F407VG/STM32F429VG)
-#define BOARD_BTT_GTR_V1_0 4213 // BigTreeTech GTR v1.0 (STM32F407IGT)
-#define BOARD_BTT_OCTOPUS_V1_0 4214 // BigTreeTech Octopus v1.0 (STM32F446ZE)
-#define BOARD_BTT_OCTOPUS_V1_1 4215 // BigTreeTech Octopus v1.1 (STM32F446ZE)
-#define BOARD_BTT_OCTOPUS_PRO_V1_0 4216 // BigTreeTech Octopus Pro v1.0 (STM32F446ZE / STM32F429ZG)
-#define BOARD_LERDGE_K 4217 // Lerdge K (STM32F407ZG)
-#define BOARD_LERDGE_S 4218 // Lerdge S (STM32F407VE)
-#define BOARD_LERDGE_X 4219 // Lerdge X (STM32F407VE)
-#define BOARD_VAKE403D 4220 // VAkE 403D (STM32F446VE)
-#define BOARD_FYSETC_S6 4221 // FYSETC S6 (STM32F446VE)
-#define BOARD_FYSETC_S6_V2_0 4222 // FYSETC S6 v2.0 (STM32F446VE)
-#define BOARD_FYSETC_SPIDER 4223 // FYSETC Spider (STM32F446VE)
-#define BOARD_FLYF407ZG 4224 // FLYmaker FLYF407ZG (STM32F407ZG)
-#define BOARD_MKS_ROBIN2 4225 // MKS_ROBIN2 (STM32F407ZE)
-#define BOARD_MKS_ROBIN_PRO_V2 4226 // MKS Robin Pro V2 (STM32F407VE)
-#define BOARD_MKS_ROBIN_NANO_V3 4227 // MKS Robin Nano V3 (STM32F407VG)
-#define BOARD_MKS_ROBIN_NANO_V3_1 4228 // MKS Robin Nano V3.1 (STM32F407VE)
-#define BOARD_MKS_MONSTER8_V1 4229 // MKS Monster8 V1 (STM32F407VE)
-#define BOARD_MKS_MONSTER8_V2 4230 // MKS Monster8 V2 (STM32F407VE)
-#define BOARD_ANET_ET4 4231 // ANET ET4 V1.x (STM32F407VG)
-#define BOARD_ANET_ET4P 4232 // ANET ET4P V1.x (STM32F407VG)
-#define BOARD_FYSETC_CHEETAH_V20 4233 // FYSETC Cheetah V2.0 (STM32F401RC)
-#define BOARD_TH3D_EZBOARD_V2 4234 // TH3D EZBoard v2.0 (STM32F405RG)
-#define BOARD_OPULO_LUMEN_REV3 4235 // Opulo Lumen PnP Controller REV3 (STM32F407VE / STM32F407VG)
-#define BOARD_MKS_ROBIN_NANO_V1_3_F4 4236 // MKS Robin Nano V1.3 and MKS Robin Nano-S V1.3 (STM32F407VE)
-#define BOARD_MKS_EAGLE 4237 // MKS Eagle (STM32F407VE)
-#define BOARD_ARTILLERY_RUBY 4238 // Artillery Ruby (STM32F401RC)
-#define BOARD_FYSETC_SPIDER_V2_2 4239 // FYSETC Spider V2.2 (STM32F446VE)
-#define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4
-#define BOARD_OPULO_LUMEN_REV4 4241 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG)
-#define BOARD_FYSETC_SPIDER_KING407 4242 // FYSETC Spider King407 (STM32F407ZG)
-#define BOARD_MKS_SKIPR_V1 4243 // MKS SKIPR v1.0 all-in-one board (STM32F407VE)
-#define BOARD_TRONXY_V10 4244 // TRONXY V10 (STM32F446ZE)
-
-//
-// ARM Cortex M7
-//
-
-#define BOARD_REMRAM_V1 5000 // RemRam v1
-#define BOARD_TEENSY41 5001 // Teensy 4.1
-#define BOARD_T41U5XBB 5002 // T41U5XBB Teensy 4.1 breakout board
-#define BOARD_NUCLEO_F767ZI 5003 // ST NUCLEO-F767ZI Dev Board
-#define BOARD_BTT_SKR_SE_BX_V2 5004 // BigTreeTech SKR SE BX V2.0 (STM32H743II)
-#define BOARD_BTT_SKR_SE_BX_V3 5005 // BigTreeTech SKR SE BX V3.0 (STM32H743II)
-#define BOARD_BTT_SKR_V3_0 5006 // BigTreeTech SKR V3.0 (STM32H743VG)
-#define BOARD_BTT_SKR_V3_0_EZ 5007 // BigTreeTech SKR V3.0 EZ (STM32H743VG)
+#define BOARD_ARMED 5200 // Arm'ed STM32F4-based controller
+#define BOARD_RUMBA32_V1_0 5201 // RUMBA32 STM32F446VE based controller from Aus3D
+#define BOARD_RUMBA32_V1_1 5202 // RUMBA32 STM32F446VE based controller from Aus3D
+#define BOARD_RUMBA32_MKS 5203 // RUMBA32 STM32F446VE based controller from Makerbase
+#define BOARD_RUMBA32_BTT 5204 // RUMBA32 STM32F446VE based controller from BIGTREETECH
+#define BOARD_BLACK_STM32F407VE 5205 // BLACK_STM32F407VE
+#define BOARD_BLACK_STM32F407ZE 5206 // BLACK_STM32F407ZE
+#define BOARD_BTT_SKR_MINI_E3_V3_0_1 5207 // BigTreeTech SKR Mini E3 V3.0.1 (STM32F401RC)
+#define BOARD_BTT_SKR_PRO_V1_1 5208 // BigTreeTech SKR Pro v1.1 (STM32F407ZG)
+#define BOARD_BTT_SKR_PRO_V1_2 5209 // BigTreeTech SKR Pro v1.2 (STM32F407ZG)
+#define BOARD_BTT_BTT002_V1_0 5210 // BigTreeTech BTT002 v1.0 (STM32F407VG)
+#define BOARD_BTT_E3_RRF 5211 // BigTreeTech E3 RRF (STM32F407VG)
+#define BOARD_BTT_SKR_V2_0_REV_A 5212 // BigTreeTech SKR v2.0 Rev A (STM32F407VG)
+#define BOARD_BTT_SKR_V2_0_REV_B 5213 // BigTreeTech SKR v2.0 Rev B (STM32F407VG/STM32F429VG)
+#define BOARD_BTT_GTR_V1_0 5214 // BigTreeTech GTR v1.0 (STM32F407IGT)
+#define BOARD_BTT_OCTOPUS_V1_0 5215 // BigTreeTech Octopus v1.0 (STM32F446ZE)
+#define BOARD_BTT_OCTOPUS_V1_1 5216 // BigTreeTech Octopus v1.1 (STM32F446ZE)
+#define BOARD_BTT_OCTOPUS_PRO_V1_0 5217 // BigTreeTech Octopus Pro v1.0 (STM32F446ZE / STM32F429ZG)
+#define BOARD_LERDGE_K 5218 // Lerdge K (STM32F407ZG)
+#define BOARD_LERDGE_S 5219 // Lerdge S (STM32F407VE)
+#define BOARD_LERDGE_X 5220 // Lerdge X (STM32F407VE)
+#define BOARD_VAKE403D 5221 // VAkE 403D (STM32F446VE)
+#define BOARD_FYSETC_S6 5222 // FYSETC S6 (STM32F446VE)
+#define BOARD_FYSETC_S6_V2_0 5223 // FYSETC S6 v2.0 (STM32F446VE)
+#define BOARD_FYSETC_SPIDER 5224 // FYSETC Spider (STM32F446VE)
+#define BOARD_FLYF407ZG 5225 // FLYmaker FLYF407ZG (STM32F407ZG)
+#define BOARD_MKS_ROBIN2 5226 // MKS_ROBIN2 (STM32F407ZE)
+#define BOARD_MKS_ROBIN_PRO_V2 5227 // MKS Robin Pro V2 (STM32F407VE)
+#define BOARD_MKS_ROBIN_NANO_V3 5228 // MKS Robin Nano V3 (STM32F407VG)
+#define BOARD_MKS_ROBIN_NANO_V3_1 5229 // MKS Robin Nano V3.1 (STM32F407VE)
+#define BOARD_MKS_MONSTER8_V1 5230 // MKS Monster8 V1 (STM32F407VE)
+#define BOARD_MKS_MONSTER8_V2 5231 // MKS Monster8 V2 (STM32F407VE)
+#define BOARD_ANET_ET4 5232 // ANET ET4 V1.x (STM32F407VG)
+#define BOARD_ANET_ET4P 5233 // ANET ET4P V1.x (STM32F407VG)
+#define BOARD_FYSETC_CHEETAH_V20 5234 // FYSETC Cheetah V2.0 (STM32F401RC)
+#define BOARD_TH3D_EZBOARD_V2 5235 // TH3D EZBoard v2.0 (STM32F405RG)
+#define BOARD_OPULO_LUMEN_REV3 5236 // Opulo Lumen PnP Controller REV3 (STM32F407VE / STM32F407VG)
+#define BOARD_MKS_ROBIN_NANO_V1_3_F4 5237 // MKS Robin Nano V1.3 and MKS Robin Nano-S V1.3 (STM32F407VE)
+#define BOARD_MKS_EAGLE 5238 // MKS Eagle (STM32F407VE)
+#define BOARD_ARTILLERY_RUBY 5239 // Artillery Ruby (STM32F401RC)
+#define BOARD_FYSETC_SPIDER_V2_2 5240 // FYSETC Spider V2.2 (STM32F446VE)
+#define BOARD_CREALITY_V24S1_301F4 5241 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4
+#define BOARD_OPULO_LUMEN_REV4 5242 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG)
+#define BOARD_FYSETC_SPIDER_KING407 5243 // FYSETC Spider King407 (STM32F407ZG)
+#define BOARD_MKS_SKIPR_V1 5244 // MKS SKIPR v1.0 all-in-one board (STM32F407VE)
+#define BOARD_TRONXY_V10 5245 // TRONXY V10 (STM32F446ZE)
+
+//
+// ARM Cortex-M7
+//
+
+#define BOARD_REMRAM_V1 6000 // RemRam v1
+#define BOARD_TEENSY41 6001 // Teensy 4.1
+#define BOARD_T41U5XBB 6002 // T41U5XBB Teensy 4.1 breakout board
+#define BOARD_NUCLEO_F767ZI 6003 // ST NUCLEO-F767ZI Dev Board
+#define BOARD_BTT_SKR_SE_BX_V2 6004 // BigTreeTech SKR SE BX V2.0 (STM32H743II)
+#define BOARD_BTT_SKR_SE_BX_V3 6005 // BigTreeTech SKR SE BX V3.0 (STM32H743II)
+#define BOARD_BTT_SKR_V3_0 6006 // BigTreeTech SKR V3.0 (STM32H743VG)
+#define BOARD_BTT_SKR_V3_0_EZ 6007 // BigTreeTech SKR V3.0 EZ (STM32H743VG)
//
// Espressif ESP32 WiFi
//
-#define BOARD_ESPRESSIF_ESP32 6000 // Generic ESP32
-#define BOARD_MRR_ESPA 6001 // MRR ESPA based on ESP32 (native pins only)
-#define BOARD_MRR_ESPE 6002 // MRR ESPE based on ESP32 (with I2S stepper stream)
-#define BOARD_E4D_BOX 6003 // E4d@BOX
-#define BOARD_RESP32_CUSTOM 6004 // Rutilea ESP32 custom board
-#define BOARD_FYSETC_E4 6005 // FYSETC E4
-#define BOARD_PANDA_ZHU 6006 // Panda_ZHU
-#define BOARD_PANDA_M4 6007 // Panda_M4
-#define BOARD_MKS_TINYBEE 6008 // MKS TinyBee based on ESP32 (with I2S stepper stream)
-#define BOARD_ENWI_ESPNP 6009 // enwi ESPNP based on ESP32 (with I2S stepper stream)
+#define BOARD_ESPRESSIF_ESP32 7000 // Generic ESP32
+#define BOARD_MRR_ESPA 7001 // MRR ESPA based on ESP32 (native pins only)
+#define BOARD_MRR_ESPE 7002 // MRR ESPE based on ESP32 (with I2S stepper stream)
+#define BOARD_E4D_BOX 7003 // E4d@BOX
+#define BOARD_RESP32_CUSTOM 7004 // Rutilea ESP32 custom board
+#define BOARD_FYSETC_E4 7005 // FYSETC E4
+#define BOARD_PANDA_ZHU 7006 // Panda_ZHU
+#define BOARD_PANDA_M4 7007 // Panda_M4
+#define BOARD_MKS_TINYBEE 7008 // MKS TinyBee based on ESP32 (with I2S stepper stream)
+#define BOARD_ENWI_ESPNP 7009 // enwi ESPNP based on ESP32 (with I2S stepper stream)
//
-// SAMD51 ARM Cortex M4
+// SAMD51 ARM Cortex-M4
//
-#define BOARD_AGCM4_RAMPS_144 6100 // RAMPS 1.4.4
-#define BOARD_BRICOLEMON_V1_0 6101 // Bricolemon
-#define BOARD_BRICOLEMON_LITE_V1_0 6102 // Bricolemon Lite
+#define BOARD_AGCM4_RAMPS_144 7100 // RAMPS 1.4.4
+#define BOARD_BRICOLEMON_V1_0 7101 // Bricolemon
+#define BOARD_BRICOLEMON_LITE_V1_0 7102 // Bricolemon Lite
//
-// SAMD21 ARM Cortex M4
+// SAMD21 ARM Cortex-M4
//
-#define BOARD_MINITRONICS20 6103 // Minitronics v2.0
+#define BOARD_MINITRONICS20 7103 // Minitronics v2.0
//
// Custom board
diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h
index e0ec241faf9c4..18bb7dba58271 100644
--- a/Marlin/src/pins/pins.h
+++ b/Marlin/src/pins/pins.h
@@ -545,6 +545,16 @@
#include "stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_USB env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt_maple env:STM32F103RC_btt_USB_maple env:STM32F103RE_btt_maple env:STM32F103RE_btt_USB_maple
#elif MB(BTT_SKR_MINI_E3_V3_0)
#include "stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M4P_V1_0)
+ #include "stm32g0/pins_BTT_MANTA_M4P_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M5P_V1_0)
+ #include "stm32g0/pins_BTT_MANTA_M5P_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_E3_EZ_V1_0)
+ #include "stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M8P_V1_0)
+ #include "stm32g0/pins_BTT_MANTA_M8P_V1_0.h" // STM32G0 env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer
+#elif MB(BTT_MANTA_M8P_V1_1)
+ #include "stm32g0/pins_BTT_MANTA_M8P_V1_1.h" // STM32G0 env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer
#elif MB(BTT_SKR_MINI_E3_V3_0_1)
#include "stm32f4/pins_BTT_SKR_MINI_E3_V3_0_1.h"// STM32F4 env:STM32F401RC_btt
#elif MB(BTT_SKR_MINI_MZ_V1_0)
diff --git a/Marlin/src/pins/stm32g0/env_validate.h b/Marlin/src/pins/stm32g0/env_validate.h
new file mode 100644
index 0000000000000..a7be76bd8bb16
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/env_validate.h
@@ -0,0 +1,26 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#if NOT_TARGET(STM32G0xx) || NOT_TARGET(STM32G0B1xx)
+ #error "Oops! Select an STM32G0 board in 'Tools > Board.'"
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h b/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h
index fc2be5401e107..cdd85a6d751c1 100644
--- a/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h
+++ b/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h
@@ -21,6 +21,8 @@
*/
#pragma once
+#include "env_validate.h"
+
/** CAUTION **
* This board definition is to facilitate support for a Filament Extrusion
* devices, used to convert waste plastic into 3D printable filament.
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h
new file mode 100644
index 0000000000000..54c2c4c77b2dd
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h
@@ -0,0 +1,340 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#include "env_validate.h"
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BTT Manta E3 EZ V1.0"
+#endif
+
+#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+ #undef NO_EEPROM_SELECTED
+ #ifndef FLASH_EEPROM_EMULATION
+ #define FLASH_EEPROM_EMULATION
+ #endif
+ #define EEPROM_PAGE_SIZE (0x800UL) // 2K
+ #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+ #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
+#endif
+
+//
+// Servos
+//
+#define SERVO0_PIN PA7 // BLTouch
+
+//
+// Probe enable
+//
+#if ENABLED(PROBE_ENABLE_DISABLE)
+ #ifndef PROBE_ENABLE_PIN
+ #define PROBE_ENABLE_PIN SERVO0_PIN
+ #endif
+#endif
+
+//
+// Trinamic StallGuard pins
+//
+#define X_DIAG_PIN PC4 // X-STOP
+#define Y_DIAG_PIN PB0 // Y-STOP
+#define Z_DIAG_PIN PC6 // Z-STOP
+#define E0_DIAG_PIN PC5 // E0-DET
+#define E1_DIAG_PIN PB1 // E1-DET
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN X_DIAG_PIN // X-STOP
+#define Y_STOP_PIN Y_DIAG_PIN // Y-STOP
+#define Z_STOP_PIN Z_DIAG_PIN // Z-STOP
+
+//
+// Z Probe (when not Z_STOP_PIN)
+//
+#define Z_MIN_PROBE_PIN PA6 // BLTouch
+
+//
+// Filament Runout Sensor
+//
+#ifndef FIL_RUNOUT_PIN
+ #define FIL_RUNOUT_PIN E0_DIAG_PIN // E0-DET
+#endif
+#ifndef FIL_RUNOUT2_PIN
+ #define FIL_RUNOUT2_PIN E1_DIAG_PIN // E1-DET
+#endif
+
+//
+// Power Supply Control
+//
+#ifndef PS_ON_PIN
+ #define PS_ON_PIN PA9 // PS-ON
+#endif
+
+//
+// Power Loss Detection
+//
+#ifndef POWER_LOSS_PIN
+ #define POWER_LOSS_PIN PB9 // PWRDET
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN PA14
+#define X_DIR_PIN PA10
+#define X_ENABLE_PIN PA13
+#ifndef X_CS_PIN
+ #define X_CS_PIN PB8
+#endif
+
+#define Y_STEP_PIN PC8
+#define Y_DIR_PIN PA15
+#define Y_ENABLE_PIN PC14
+#ifndef Y_CS_PIN
+ #define Y_CS_PIN PC9
+#endif
+
+#define Z_STEP_PIN PD2
+#define Z_DIR_PIN PD4
+#define Z_ENABLE_PIN PD3
+#ifndef Z_CS_PIN
+ #define Z_CS_PIN PD0
+#endif
+
+#define E0_STEP_PIN PD5
+#define E0_DIR_PIN PD6
+#define E0_ENABLE_PIN PB3
+#ifndef E0_CS_PIN
+ #define E0_CS_PIN PD1
+#endif
+
+#define E1_STEP_PIN PB7
+#define E1_DIR_PIN PB6
+#define E1_ENABLE_PIN PB4
+#ifndef E1_CS_PIN
+ #define E1_CS_PIN PB5
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+ #ifndef TMC_SW_MOSI
+ #define TMC_SW_MOSI PC12 // Shared with SPI header, Pin 5 (SPI3)
+ #endif
+ #ifndef TMC_SW_MISO
+ #define TMC_SW_MISO PC11 // Shared with SPI header, Pin 6 (SPI3)
+ #endif
+ #ifndef TMC_SW_SCK
+ #define TMC_SW_SCK PC10 // Shared with SPI header, Pin 4 (SPI3)
+ #endif
+#endif
+
+#if HAS_TMC_UART
+ #define X_SERIAL_TX_PIN PB8 // X_CS_PIN
+ #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
+
+ #define Y_SERIAL_TX_PIN PC9 // Y_CS_PIN
+ #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
+
+ #define Z_SERIAL_TX_PIN PD0 // Z_CS_PIN
+ #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
+
+ #define E0_SERIAL_TX_PIN PD1 // E0_CS_PIN
+ #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
+
+ #define E1_SERIAL_TX_PIN PB5 // E1_CS_PIN
+ #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN PA4 // Analog Input "TH0"
+#define TEMP_1_PIN PA5 // Analog Input "TH1"
+#define TEMP_BED_PIN PA3 // Analog Input "TB"
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN PB11 // "HE0"
+#define HEATER_1_PIN PB10 // "HE1"
+#define HEATER_BED_PIN PB2 // "HB"
+
+#define FAN_PIN PA8 // "FAN0"
+#define FAN1_PIN PB15 // "FAN1"
+#define FAN2_PIN PB14 // "FAN2"
+
+//
+// Auto fans
+//
+#if HOTENDS == 2
+ #ifndef E0_AUTO_FAN_PIN
+ #define E0_AUTO_FAN_PIN FAN1_PIN
+ #endif
+ #ifndef E1_AUTO_FAN_PIN
+ #define E1_AUTO_FAN_PIN FAN2_PIN
+ #endif
+#else
+ #ifndef E0_AUTO_FAN_PIN
+ #define E0_AUTO_FAN_PIN FAN1_PIN
+ #endif
+ #ifndef CONTROLLER_FAN_PIN
+ #define CONTROLLER_FAN_PIN FAN2_PIN
+ #endif
+#endif
+
+/**
+ * Manta E3 EZ V1.0
+ * ------
+ * (BEEPER) PC1 | 1 2 | PC2 (BTN_ENC)
+ * (BTN_EN1) PC3 | 3 4 | RESET
+ * (BTN_EN2) PC0 5 6 | PA0 (LCD_D4)
+ * (LCD_RS) PA2 | 7 8 | PA1 (LCD_EN)
+ * GND | 9 10 | 5V
+ * ------
+ * EXP1
+ */
+#define EXP1_01_PIN PC1
+#define EXP1_02_PIN PC2
+#define EXP1_03_PIN PC3
+#define EXP1_04_PIN -1
+#define EXP1_05_PIN PC0
+#define EXP1_06_PIN PA0
+#define EXP1_07_PIN PA2
+#define EXP1_08_PIN PA1
+#define EXP1_09_PIN -1
+#define EXP1_10_PIN -1
+
+#if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI
+ #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING
+ #error "CAUTION! Ender-3 V2 display requires a custom cable with TX = PA0, RX = PC2. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)"
+ #endif
+
+ /**
+ * Ender-3 V2 display Manta E3 EZ V1.0 Ender-3 V2 display --> Manta E3 EZ V1.0
+ * ------ ------ RX 3 --> 5 P0_15
+ * -- | 1 2 | -- (BEEPER) PC1 | 1 2 | PC2 (BTN_ENC) TX 4 --> 9 P0_16
+ * (MANTA TX1) RX | 3 4 | TX (MANTA RX1) (BTN_EN1) PC3 | 3 4 | RESET BEEPER 6 --> 10 P2_08
+ * (BTN_ENC) ENT 5 6 | BEEPER (BTN_EN2) PC0 5 6 | PA0 (LCD_D4)
+ * (BTN_E2) B | 7 8 | A (BTN_E1) (LCD_RS) PA2 | 7 8 | PA1 (LCD_EN)
+ * GND | 9 10 | 5V GND | 9 10 | 5V
+ * ------ ------
+ */
+
+ #define BEEPER_PIN EXP1_01_PIN
+ #define BTN_EN1 EXP1_08_PIN
+ #define BTN_EN2 EXP1_07_PIN
+ #define BTN_ENC EXP1_05_PIN
+
+#elif HAS_WIRED_LCD
+
+ #if ENABLED(CR10_STOCKDISPLAY)
+
+ #define BEEPER_PIN EXP1_01_PIN
+
+ #define BTN_EN1 EXP1_03_PIN
+ #define BTN_EN2 EXP1_05_PIN
+ #define BTN_ENC EXP1_02_PIN
+
+ #define LCD_PINS_RS EXP1_07_PIN
+ #define LCD_PINS_ENABLE EXP1_08_PIN
+ #define LCD_PINS_D4 EXP1_06_PIN
+
+ #elif ENABLED(ZONESTAR_LCD) // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD!
+
+ #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING
+ #error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)"
+ #endif
+
+ #define LCD_PINS_RS EXP1_06_PIN
+ #define LCD_PINS_ENABLE EXP1_02_PIN
+ #define LCD_PINS_D4 EXP1_07_PIN
+ #define LCD_PINS_D5 EXP1_05_PIN
+ #define LCD_PINS_D6 EXP1_03_PIN
+ #define LCD_PINS_D7 EXP1_01_PIN
+ #define ADC_KEYPAD_PIN PA7 // Repurpose default SERVO0_PIN for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD!
+
+ #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
+
+ #define BTN_EN1 EXP1_03_PIN
+ #define BTN_EN2 EXP1_05_PIN
+ #define BTN_ENC EXP1_02_PIN
+
+ #define DOGLCD_CS EXP1_07_PIN
+ #define DOGLCD_A0 EXP1_06_PIN
+ #define DOGLCD_SCK EXP1_01_PIN
+ #define DOGLCD_MOSI EXP1_08_PIN
+ #define FORCE_SOFT_SPI
+ #define LCD_BACKLIGHT_PIN -1
+
+ #else
+
+ #error "Only ZONESTAR_LCD, MKS_MINI_12864, ENDER2_STOCKDISPLAY, and CR10_STOCKDISPLAY are currently supported on the BTT_MANTA_E3_EZ_V1_0."
+
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+//
+// SD Support
+//
+
+#ifndef SDCARD_CONNECTION
+ #define SDCARD_CONNECTION ONBOARD
+#endif
+
+#define SD_DETECT_PIN -1
+
+#if SD_CONNECTION_IS(LCD) && (BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050) || IS_TFTGLCD_PANEL)
+ #define SD_SS_PIN EXP1_05_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+ #error "SD CUSTOM_CABLE is not compatible with Manta E3 EZ."
+#endif
+
+#define ONBOARD_SPI_DEVICE 3 // SPI3 -> used only by HAL/STM32F1...
+#define ONBOARD_SD_CS_PIN PC13 // Chip select for "System" SD card
+
+#define ENABLE_SPI3
+#define SDSS ONBOARD_SD_CS_PIN
+#define SD_SS_PIN ONBOARD_SD_CS_PIN
+#define SD_SCK_PIN PC10
+#define SD_MISO_PIN PC11
+#define SD_MOSI_PIN PC12
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+ #define NEOPIXEL_PIN PC7 // RGB
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h
new file mode 100644
index 0000000000000..876475f883555
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h
@@ -0,0 +1,313 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#include "env_validate.h"
+
+//#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BTT Manta M4P V1.0"
+#endif
+
+#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+ #undef NO_EEPROM_SELECTED
+ #ifndef FLASH_EEPROM_EMULATION
+ #define FLASH_EEPROM_EMULATION
+ #endif
+ #define EEPROM_PAGE_SIZE (0x800UL) // 2K
+ #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+ #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
+#endif
+
+//
+// Servos
+//
+#define SERVO0_PIN PA1 // SERVOS
+
+//
+// Probe enable
+//
+#if ENABLED(PROBE_ENABLE_DISABLE)
+ #ifndef PROBE_ENABLE_PIN
+ #define PROBE_ENABLE_PIN SERVO0_PIN
+ #endif
+#endif
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN PC0 // X-STOP
+#define Y_STOP_PIN PC1 // Y-STOP
+#define Z_STOP_PIN PC2 // Z-STOP
+
+//
+// Z Probe must be this pin
+//
+#define Z_MIN_PROBE_PIN PC14 // PROBE
+
+//
+// Filament Runout Sensor
+//
+#ifndef FIL_RUNOUT_PIN
+ #define FIL_RUNOUT_PIN PC15 // E0-STOP
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN PC6
+#define X_DIR_PIN PA14
+#define X_ENABLE_PIN PC7
+#ifndef X_CS_PIN
+ #define X_CS_PIN PB12
+#endif
+
+#define Y_STEP_PIN PB10
+#define Y_DIR_PIN PB2
+#define Y_ENABLE_PIN PB11
+#ifndef Y_CS_PIN
+ #define Y_CS_PIN PC10
+#endif
+
+#define Z_STEP_PIN PB0
+#define Z_DIR_PIN PC5
+#define Z_ENABLE_PIN PB1
+#ifndef Z_CS_PIN
+ #define Z_CS_PIN PC9
+#endif
+
+#define E0_STEP_PIN PB3
+#define E0_DIR_PIN PB4
+#define E0_ENABLE_PIN PD5
+#ifndef E0_CS_PIN
+ #define E0_CS_PIN PA13
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+ #ifndef TMC_SW_MOSI
+ #define TMC_SW_MOSI PB15
+ #endif
+ #ifndef TMC_SW_MISO
+ #define TMC_SW_MISO PB14
+ #endif
+ #ifndef TMC_SW_SCK
+ #define TMC_SW_SCK PB13
+ #endif
+#endif
+
+#if HAS_TMC_UART
+ #define X_SERIAL_TX_PIN PB12
+ #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
+
+ #define Y_SERIAL_TX_PIN PC10
+ #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
+
+ #define Z_SERIAL_TX_PIN PC9
+ #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
+
+ #define E0_SERIAL_TX_PIN PA13
+ #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN PA0 // Analog Input "TH0"
+#define TEMP_BED_PIN PC4 // Analog Input "TB0"
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN PC8 // "HE"
+#define HEATER_BED_PIN PD8 // "HB"
+
+#define FAN_PIN PD2 // "FAN0"
+#define FAN1_PIN PD3 // "FAN1"
+#define FAN2_PIN PD4 // "FAN2"
+
+/**
+ * ------ ------
+ * (BEEPER) PD6 | 1 2 | PB8 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK)
+ * (LCD_EN) PB9 | 3 4 | PC3 (LCD_RS) (BTN_EN1) PC11 | 3 4 | PA8 (SD_SS)
+ * (LCD_D4) PA15 | 5 6 PA10 (LCD_D5) (BTN_EN2) PC12 | 5 6 PB15 (MOSI)
+ * (LCD_D6) PA9 | 7 8 | PB5 (LCD_D7) (SD_DETECT) PC13 | 7 8 | RESET
+ * GND | 9 10 | 5V GND | 9 10 | --
+ * ------ ------
+ * EXP1 EXP2
+ */
+#define EXP1_01_PIN PD6
+#define EXP1_02_PIN PB8
+#define EXP1_03_PIN PB9
+#define EXP1_04_PIN PC3
+#define EXP1_05_PIN PA15
+#define EXP1_06_PIN PA10
+#define EXP1_07_PIN PA9
+#define EXP1_08_PIN PB5
+
+#define EXP2_01_PIN PB14
+#define EXP2_02_PIN PB13
+#define EXP2_03_PIN PC11
+#define EXP2_04_PIN PA8
+#define EXP2_05_PIN PC12
+#define EXP2_06_PIN PB15
+#define EXP2_07_PIN PC13
+#define EXP2_08_PIN -1
+
+//
+// Onboard SD card
+// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
+//
+#if SD_CONNECTION_IS(LCD)
+ #define SDSS EXP2_04_PIN
+ #define SD_SS_PIN SDSS
+ #define SD_SCK_PIN EXP2_02_PIN
+ #define SD_MISO_PIN EXP2_01_PIN
+ #define SD_MOSI_PIN EXP2_06_PIN
+ #define SD_DETECT_PIN EXP2_07_PIN
+#elif SD_CONNECTION_IS(ONBOARD)
+ #define SD_SCK_PIN PA5
+ #define SD_MISO_PIN PA6
+ #define SD_MOSI_PIN PA7
+ #define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card
+ #define SD_SS_PIN ONBOARD_SD_CS_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+ #error "No custom SD drive cable defined for this board."
+#endif
+
+//
+// LCDs and Controllers
+//
+#if IS_TFTGLCD_PANEL
+
+ #if ENABLED(TFTGLCD_PANEL_SPI)
+ #define TFTGLCD_CS EXP2_03_PIN
+ #endif
+
+#elif HAS_WIRED_LCD
+
+ #define BEEPER_PIN EXP1_01_PIN
+ #define BTN_ENC EXP1_02_PIN
+
+ #if ENABLED(CR10_STOCKDISPLAY)
+
+ #define LCD_PINS_RS EXP1_07_PIN
+
+ #define BTN_EN1 EXP1_03_PIN
+ #define BTN_EN2 EXP1_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_08_PIN
+ #define LCD_PINS_D4 EXP1_06_PIN
+
+ #elif ENABLED(MKS_MINI_12864)
+
+ #define DOGLCD_A0 EXP1_07_PIN
+ #define DOGLCD_CS EXP1_06_PIN
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #else
+
+ #define LCD_PINS_RS EXP1_04_PIN
+
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_03_PIN
+ #define LCD_PINS_D4 EXP1_05_PIN
+
+ #if ENABLED(FYSETC_MINI_12864)
+ #define DOGLCD_CS EXP1_03_PIN
+ #define DOGLCD_A0 EXP1_04_PIN
+ //#define LCD_BACKLIGHT_PIN -1
+
+ #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
+ // results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+ #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally.
+ #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+ #ifndef RGB_LED_R_PIN
+ #define RGB_LED_R_PIN EXP1_06_PIN
+ #endif
+ #ifndef RGB_LED_G_PIN
+ #define RGB_LED_G_PIN EXP1_07_PIN
+ #endif
+ #ifndef RGB_LED_B_PIN
+ #define RGB_LED_B_PIN EXP1_08_PIN
+ #endif
+ #elif ENABLED(FYSETC_MINI_12864_2_1)
+ #define NEOPIXEL_PIN EXP1_06_PIN
+ #endif
+ #endif // !FYSETC_MINI_12864
+
+ #if IS_ULTIPANEL
+ #define LCD_PINS_D5 EXP1_06_PIN
+ #define LCD_PINS_D6 EXP1_07_PIN
+ #define LCD_PINS_D7 EXP1_08_PIN
+
+ #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
+ #endif
+
+ #endif
+
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+// Alter timing for graphical display
+#if IS_U8GLIB_ST7920
+ #ifndef BOARD_ST7920_DELAY_1
+ #define BOARD_ST7920_DELAY_1 120
+ #endif
+ #ifndef BOARD_ST7920_DELAY_2
+ #define BOARD_ST7920_DELAY_2 80
+ #endif
+ #ifndef BOARD_ST7920_DELAY_3
+ #define BOARD_ST7920_DELAY_3 580
+ #endif
+#endif
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+ #define NEOPIXEL_PIN PD0
+#endif
+
+#ifndef NEOPIXEL2_PIN
+ #define NEOPIXEL2_PIN PD1
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h
new file mode 100644
index 0000000000000..f4ce5a16d3b00
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h
@@ -0,0 +1,341 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#include "env_validate.h"
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BTT Manta M5P V1.0"
+#endif
+
+#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+ #undef NO_EEPROM_SELECTED
+ #ifndef FLASH_EEPROM_EMULATION
+ #define FLASH_EEPROM_EMULATION
+ #endif
+ #define EEPROM_PAGE_SIZE (0x800UL) // 2K
+ #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+ #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
+#endif
+
+//
+// Servos
+//
+#define SERVO0_PIN PC15 // PROBE
+
+//
+// Probe enable
+//
+#if ENABLED(PROBE_ENABLE_DISABLE)
+ #ifndef PROBE_ENABLE_PIN
+ #define PROBE_ENABLE_PIN SERVO0_PIN
+ #endif
+#endif
+
+//
+// Trinamic StallGuard pins
+//
+#define X_DIAG_PIN PD3 // MIN1
+#define Y_DIAG_PIN PD2 // MIN2
+#define Z_DIAG_PIN PC3 // MIN3
+#define E0_DIAG_PIN PC2 // MIN4
+#define E1_DIAG_PIN -1
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN X_DIAG_PIN // MIN1
+#define Y_STOP_PIN Y_DIAG_PIN // MIN1
+#define Z_STOP_PIN Z_DIAG_PIN // MIN3
+
+//
+// Z Probe (when not Z_STOP_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+ #define Z_MIN_PROBE_PIN PC13 // PROBE
+ //#define Z_MIN_PROBE_PIN PC15 // IND-DET (with adjustable pullup set via jumper)
+#endif
+
+//
+// Filament Runout Sensor
+//
+#ifndef FIL_RUNOUT_PIN
+ #define FIL_RUNOUT_PIN E0_DIAG_PIN // MIN4
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN PC8
+#define X_DIR_PIN PC9
+#define X_ENABLE_PIN PA15
+#ifndef X_CS_PIN
+ #define X_CS_PIN PD9
+#endif
+
+#define Y_STEP_PIN PA10
+#define Y_DIR_PIN PA14
+#define Y_ENABLE_PIN PA13
+#ifndef Y_CS_PIN
+ #define Y_CS_PIN PD8
+#endif
+
+#define Z_STEP_PIN PC6
+#define Z_DIR_PIN PC7
+#define Z_ENABLE_PIN PA9
+#ifndef Z_CS_PIN
+ #define Z_CS_PIN PB10
+#endif
+
+#define E0_STEP_PIN PB12
+#define E0_DIR_PIN PB11
+#define E0_ENABLE_PIN PA8
+#ifndef E0_CS_PIN
+ #define E0_CS_PIN PB2
+#endif
+
+#define E1_STEP_PIN PB0
+#define E1_DIR_PIN PB1
+#define E1_ENABLE_PIN PC4
+#ifndef E1_CS_PIN
+ #define E1_CS_PIN PA6
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+ #ifndef TMC_SW_MOSI
+ #define TMC_SW_MOSI PB15 // Shared with SPI header, Pin 5 (SPI2)
+ #endif
+ #ifndef TMC_SW_MISO
+ #define TMC_SW_MISO PB14 // Shared with SPI header, Pin 6 (SPI2)
+ #endif
+ #ifndef TMC_SW_SCK
+ #define TMC_SW_SCK PB13 // Shared with SPI header, Pin 4 (SPI2)
+ #endif
+#endif
+
+#if HAS_TMC_UART
+ #define X_SERIAL_TX_PIN PD9 // X_CS_PIN
+ #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
+
+ #define Y_SERIAL_TX_PIN PD8 // Y_CS_PIN
+ #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
+
+ #define Z_SERIAL_TX_PIN PB10 // Z_CS_PIN
+ #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
+
+ #define E0_SERIAL_TX_PIN PB2 // E0_CS_PIN
+ #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
+
+ #define E1_SERIAL_TX_PIN PA6 // E1_CS_PIN
+ #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN PA1 // Analog Input "TH0"
+#define TEMP_1_PIN PA2 // Analog Input "TH1"
+#define TEMP_BED_PIN PA0 // Analog Input "TB"
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN PC5 // "HE0"
+#define HEATER_1_PIN PA7 // "HE1"
+#define HEATER_BED_PIN PA5 // "HB"
+
+#define FAN_PIN PA4 // "FAN0"
+#define FAN1_PIN PA3 // "FAN1"
+
+//
+// Auto fans
+//
+#ifndef E0_AUTO_FAN_PIN
+ #define E0_AUTO_FAN_PIN FAN1_PIN
+#endif
+
+/**
+ * ------ ------
+ * (BEEPER) PD5 | 1 2 | PD4 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK)
+ * (LCD_EN) PB3 | 3 4 | PD6 (LCD_RS) (BTN_EN1) PB8 | 3 4 | PB9 (SD_SS)
+ * (LCD_D4) PB5 | 5 6 PB4 (LCD_D5) (BTN_EN2) PC10 | 5 6 PB15 (MOSI)
+ * (LCD_D6) PB7 | 7 8 | PB6 (LCD_D7) (SD_DETECT) PC12 | 7 8 | PF2
+ * GND | 9 10 | 5V GND | 9 10 | --
+ * ------ ------
+ * EXP1 EXP2
+ */
+#define EXP1_01_PIN PD5
+#define EXP1_02_PIN PD4
+#define EXP1_03_PIN PB3
+#define EXP1_04_PIN PD6
+#define EXP1_05_PIN PB5
+#define EXP1_06_PIN PB4
+#define EXP1_07_PIN PB7
+#define EXP1_08_PIN PB6
+
+#define EXP2_01_PIN PB14
+#define EXP2_02_PIN PB13
+#define EXP2_03_PIN PB8
+#define EXP2_04_PIN PB9
+#define EXP2_05_PIN PC10
+#define EXP2_06_PIN PB15
+#define EXP2_07_PIN PC12
+#define EXP2_08_PIN -1
+
+//
+// Onboard SD card
+// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
+//
+#if SD_CONNECTION_IS(LCD)
+ #define SDSS EXP2_04_PIN
+ #define SD_SS_PIN SDSS
+ #define SD_SCK_PIN EXP2_02_PIN
+ #define SD_MISO_PIN EXP2_01_PIN
+ #define SD_MOSI_PIN EXP2_06_PIN
+ #define SD_DETECT_PIN EXP2_07_PIN
+#elif SD_CONNECTION_IS(ONBOARD)
+ #define SD_SCK_PIN PB13
+ #define SD_MISO_PIN PB14
+ #define SD_MOSI_PIN PB15
+ #define ONBOARD_SD_CS_PIN PC1 // Chip select for "System" SD card
+ #define SD_SS_PIN ONBOARD_SD_CS_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+ #error "No custom SD drive cable defined for this board."
+#endif
+
+//
+// LCDs and Controllers
+//
+#if IS_TFTGLCD_PANEL
+
+ #if ENABLED(TFTGLCD_PANEL_SPI)
+ #define TFTGLCD_CS EXP2_03_PIN
+ #endif
+
+#elif HAS_WIRED_LCD
+
+ #define BEEPER_PIN EXP1_01_PIN
+ #define BTN_ENC EXP1_02_PIN
+
+ #if ENABLED(CR10_STOCKDISPLAY)
+
+ #define LCD_PINS_RS EXP1_07_PIN
+
+ #define BTN_EN1 EXP1_03_PIN
+ #define BTN_EN2 EXP1_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_08_PIN
+ #define LCD_PINS_D4 EXP1_06_PIN
+
+ #elif ENABLED(MKS_MINI_12864)
+
+ #define DOGLCD_A0 EXP1_07_PIN
+ #define DOGLCD_CS EXP1_06_PIN
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #else
+
+ #define LCD_PINS_RS EXP1_04_PIN
+
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_03_PIN
+ #define LCD_PINS_D4 EXP1_05_PIN
+
+ #if ENABLED(FYSETC_MINI_12864)
+ #define DOGLCD_CS EXP1_03_PIN
+ #define DOGLCD_A0 EXP1_04_PIN
+ //#define LCD_BACKLIGHT_PIN -1
+
+ #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
+ // results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+ #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally.
+ #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+ #ifndef RGB_LED_R_PIN
+ #define RGB_LED_R_PIN EXP1_06_PIN
+ #endif
+ #ifndef RGB_LED_G_PIN
+ #define RGB_LED_G_PIN EXP1_07_PIN
+ #endif
+ #ifndef RGB_LED_B_PIN
+ #define RGB_LED_B_PIN EXP1_08_PIN
+ #endif
+ #elif ENABLED(FYSETC_MINI_12864_2_1)
+ #define NEOPIXEL_PIN EXP1_06_PIN
+ #endif
+ #endif // !FYSETC_MINI_12864
+
+ #if IS_ULTIPANEL
+ #define LCD_PINS_D5 EXP1_06_PIN
+ #define LCD_PINS_D6 EXP1_07_PIN
+ #define LCD_PINS_D7 EXP1_08_PIN
+
+ #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
+ #endif
+
+ #endif
+
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+// Alter timing for graphical display
+#if IS_U8GLIB_ST7920
+ #ifndef BOARD_ST7920_DELAY_1
+ #define BOARD_ST7920_DELAY_1 120
+ #endif
+ #ifndef BOARD_ST7920_DELAY_2
+ #define BOARD_ST7920_DELAY_2 80
+ #endif
+ #ifndef BOARD_ST7920_DELAY_3
+ #define BOARD_ST7920_DELAY_3 580
+ #endif
+#endif
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+ #define NEOPIXEL_PIN PC11 // RGB1
+#endif
+
+#ifndef NEOPIXEL2_PIN
+ #define NEOPIXEL2_PIN PC14 // RGB2
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h
new file mode 100644
index 0000000000000..4f8d30b6b7faa
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h
@@ -0,0 +1,79 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+// Include common Manta M8P pins
+#include "pins_BTT_MANTA_M8P_common.h"
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BTT Manta M8P V1.0"
+#endif
+
+//
+// Steppers
+//
+
+#define E1_STEP_PIN PA10 // M6
+#define E1_DIR_PIN PD15
+#define E1_ENABLE_PIN PA15
+#ifndef E1_CS_PIN
+ #define E1_CS_PIN PF8
+#endif
+
+#define E2_STEP_PIN PD12 // M7
+#define E2_DIR_PIN PD11
+#define E2_ENABLE_PIN PD14
+#ifndef E2_CS_PIN
+ #define E2_CS_PIN PD13
+#endif
+
+#define E3_STEP_PIN PD10 // M8
+#define E3_DIR_PIN PD8
+#define E3_ENABLE_PIN PD9
+#ifndef E3_CS_PIN
+ #define E3_CS_PIN PC7
+#endif
+
+#if HAS_TMC_UART
+ #define E1_SERIAL_TX_PIN PF8
+ #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
+
+ #define E2_SERIAL_TX_PIN PD13
+ #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN
+
+ #define E3_SERIAL_TX_PIN PC7
+ #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+ #define NEOPIXEL_PIN PC6
+#endif
+
+#ifndef NEOPIXEL2_PIN
+ #define NEOPIXEL2_PIN PA9
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h
new file mode 100644
index 0000000000000..a21bb59e69c3a
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h
@@ -0,0 +1,78 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+// Include common Manta M8P pins
+#include "pins_BTT_MANTA_M8P_common.h"
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BTT Manta M8P V1.1"
+#endif
+
+//
+// Steppers
+//
+#define E1_STEP_PIN PA10 // M6
+#define E1_DIR_PIN PA14
+#define E1_ENABLE_PIN PA15
+#ifndef E1_CS_PIN
+ #define E1_CS_PIN PF8
+#endif
+
+#define E2_STEP_PIN PD11 // M7
+#define E2_DIR_PIN PD9
+#define E2_ENABLE_PIN PD15
+#ifndef E2_CS_PIN
+ #define E2_CS_PIN PD14
+#endif
+
+#define E3_STEP_PIN PD8 // M8
+#define E3_DIR_PIN PC6
+#define E3_ENABLE_PIN PC7
+#ifndef E3_CS_PIN
+ #define E3_CS_PIN PD10
+#endif
+
+#if HAS_TMC_UART
+ #define E1_SERIAL_TX_PIN PF8
+ #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
+
+ #define E2_SERIAL_TX_PIN PD14
+ #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN
+
+ #define E3_SERIAL_TX_PIN PD10
+ #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+ #define NEOPIXEL_PIN PA9
+#endif
+
+#ifndef NEOPIXEL2_PIN
+ #define NEOPIXEL2_PIN PB15
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h
new file mode 100644
index 0000000000000..0d4a74b6f95c4
--- /dev/null
+++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h
@@ -0,0 +1,397 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#include "env_validate.h"
+
+//#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4
+
+#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+ #undef NO_EEPROM_SELECTED
+ #ifndef FLASH_EEPROM_EMULATION
+ #define FLASH_EEPROM_EMULATION
+ #endif
+ #define EEPROM_PAGE_SIZE (0x800UL) // 2K
+ #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+ #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
+#endif
+
+//
+// Servos
+//
+#define SERVO0_PIN PB1 // PROBE
+
+//
+// Probe enable
+//
+#if ENABLED(PROBE_ENABLE_DISABLE)
+ #ifndef PROBE_ENABLE_PIN
+ #define PROBE_ENABLE_PIN SERVO0_PIN
+ #endif
+#endif
+
+//
+// Trinamic Stallguard pins
+//
+#define X_DIAG_PIN PF3 // MIN1
+#define Y_DIAG_PIN PF4 // MIN2
+#define Z_DIAG_PIN PF5 // MIN3
+#define Z2_DIAG_PIN PC0 // MIN4
+#define E0_DIAG_PIN PC1 // MIN5
+#define E1_DIAG_PIN PC2 // MIN6
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+ #define Z_MIN_PROBE_PIN PB2 // PROBE
+ //#define Z_MIN_PROBE_PIN PF6 // IND-PROBE (with adjustable voltage & pullup set via jumpers)
+#endif
+
+//
+// Check for additional used endstop pins
+//
+#if HAS_EXTRA_ENDSTOPS
+ #define _ENDSTOP_IS_ANY(ES) X2_USE_ENDSTOP == ES || Y2_USE_ENDSTOP == ES || Z2_USE_ENDSTOP == ES || Z3_USE_ENDSTOP == ES || Z4_USE_ENDSTOP == ES
+ #if _ENDSTOP_IS_ANY(_XMIN_) || _ENDSTOP_IS_ANY(_XMAX_)
+ #define NEEDS_X_MINMAX 1
+ #endif
+ #if _ENDSTOP_IS_ANY(_YMIN_) || _ENDSTOP_IS_ANY(_YMAX_)
+ #define NEEDS_Y_MINMAX 1
+ #endif
+ #undef _ENDSTOP_IS_ANY
+#endif
+
+//
+// Limit Switches
+//
+#ifdef X_STALL_SENSITIVITY
+ #define X_STOP_PIN X_DIAG_PIN
+ #if X_HOME_TO_MIN
+ #define X_MAX_PIN E0_DIAG_PIN // MIN5
+ #else
+ #define X_MIN_PIN E0_DIAG_PIN // MIN5
+ #endif
+#elif EITHER(DUAL_X_CARRIAGE, NEEDS_X_MINMAX)
+ #ifndef X_MIN_PIN
+ #define X_MIN_PIN X_DIAG_PIN // MIN1
+ #endif
+ #ifndef X_MAX_PIN
+ #define X_MAX_PIN E0_DIAG_PIN // MIN5
+ #endif
+#else
+ #define X_STOP_PIN X_DIAG_PIN // MIN1
+#endif
+
+#ifdef Y_STALL_SENSITIVITY
+ #define Y_STOP_PIN Y_DIAG_PIN
+ #if Y_HOME_TO_MIN
+ #define Y_MAX_PIN E1_DIAG_PIN // MIN6
+ #else
+ #define Y_MIN_PIN E1_DIAG_PIN // MIN6
+ #endif
+#elif NEEDS_Y_MINMAX
+ #ifndef Y_MIN_PIN
+ #define Y_MIN_PIN Y_DIAG_PIN // MIN2
+ #endif
+ #ifndef Y_MAX_PIN
+ #define Y_MAX_PIN E1_DIAG_PIN // MIN6
+ #endif
+#else
+ #define Y_STOP_PIN Y_DIAG_PIN // MIN2
+#endif
+
+#define Z_STOP_PIN Z_DIAG_PIN // MIN3
+
+#undef NEEDS_X_MINMAX
+#undef NEEDS_Y_MINMAX
+
+//
+// Filament Runout Sensors
+//
+#define FIL_RUNOUT_PIN PC1 // MIN5
+#define FIL_RUNOUT2_PIN PC2 // MIN6
+
+#ifndef PS_ON_PIN
+ #define PS_ON_PIN PC3 // PS-ON
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN PE2 // M1
+#define X_DIR_PIN PB4
+#define X_ENABLE_PIN PC11
+#ifndef X_CS_PIN
+ #define X_CS_PIN PC10
+#endif
+
+#define Y_STEP_PIN PF12 // M2
+#define Y_DIR_PIN PF11
+#define Y_ENABLE_PIN PB3
+#ifndef Y_CS_PIN
+ #define Y_CS_PIN PF13
+#endif
+
+#define Z_STEP_PIN PD7 // M3
+#define Z_DIR_PIN PD6
+#define Z_ENABLE_PIN PF10
+#ifndef Z_CS_PIN
+ #define Z_CS_PIN PF9
+#endif
+
+#define Z2_STEP_PIN PD3 // M4
+#define Z2_DIR_PIN PD2
+#define Z2_ENABLE_PIN PD5
+#ifndef Z2_CS_PIN
+ #define Z2_CS_PIN PD4
+#endif
+
+#define E0_STEP_PIN PC9 // M5
+#define E0_DIR_PIN PC8
+#define E0_ENABLE_PIN PD1
+#ifndef E0_CS_PIN
+ #define E0_CS_PIN PD0
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+ #ifndef TMC_SW_MOSI
+ #define TMC_SW_MOSI PA7
+ #endif
+ #ifndef TMC_SW_MISO
+ #define TMC_SW_MISO PA6
+ #endif
+ #ifndef TMC_SW_SCK
+ #define TMC_SW_SCK PA5
+ #endif
+#endif
+
+#if HAS_TMC_UART
+ #define X_SERIAL_TX_PIN PC10
+ #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
+
+ #define Y_SERIAL_TX_PIN PF13
+ #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
+
+ #define Z_SERIAL_TX_PIN PF9
+ #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
+
+ #define Z2_SERIAL_TX_PIN PD4
+ #define Z2_SERIAL_RX_PIN Z2_SERIAL_TX_PIN
+
+ #define E0_SERIAL_TX_PIN PD0
+ #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
+
+ // Reduce baud rate to improve software serial reliability
+ #define TMC_BAUD_RATE 19200
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_BED_PIN PA0 // TB
+#define TEMP_0_PIN PA1 // TH0
+#define TEMP_1_PIN PA2 // TH1
+#define TEMP_2_PIN PA3 // TH2
+#define TEMP_3_PIN PA4 // TH3
+
+//
+// Heaters / Fans
+//
+#define HEATER_BED_PIN PB7 // BED-OUT
+#define HEATER_0_PIN PE3 // HE0
+#define HEATER_1_PIN PB5 // HE1
+#define HEATER_2_PIN PB6 // HE2
+#define HEATER_3_PIN PE1 // HE3
+
+#define FAN_PIN PE6 // FAN0
+#define FAN1_PIN PE0 // FAN1
+#define FAN2_PIN PC12 // FAN2
+#define FAN3_PIN PE5 // FAN3
+#define FAN4_PIN PE4 // FAN4
+#define FAN5_PIN PB8 // FAN5
+#define FAN6_PIN PB9 // FAN6
+
+//
+// SD Support
+//
+#ifndef SDCARD_CONNECTION
+ #if HAS_WIRED_LCD
+ #define SDCARD_CONNECTION LCD
+ #else
+ #define SDCARD_CONNECTION ONBOARD
+ #endif
+#endif
+
+/**
+ * ------ ------
+ * (BEEPER) PE9 | 1 2 | PE10 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK)
+ * (LCD_EN) PE11 | 3 4 | PE12 (LCD_RS) (BTN_EN1) PF7 | 3 4 | PB12 (SD_SS)
+ * (LCD_D4) PE13 | 5 6 PE14 (LCD_D5) (BTN_EN2) PE7 | 5 6 PB11 (MOSI)
+ * (LCD_D6) PE15 | 7 8 | PB10 (LCD_D7) (SD_DETECT) PE8 | 7 8 | RESET
+ * GND | 9 10 | 5V GND | 9 10 | --
+ * ------ ------
+ * EXP1 EXP2
+ */
+#define EXP1_01_PIN PE9
+#define EXP1_02_PIN PE10
+#define EXP1_03_PIN PE11
+#define EXP1_04_PIN PE12
+#define EXP1_05_PIN PE13
+#define EXP1_06_PIN PE14
+#define EXP1_07_PIN PE15
+#define EXP1_08_PIN PB10
+
+#define EXP2_01_PIN PB14
+#define EXP2_02_PIN PB13
+#define EXP2_03_PIN PF7
+#define EXP2_04_PIN PB12
+#define EXP2_05_PIN PE7
+#define EXP2_06_PIN PB11
+#define EXP2_07_PIN PE8
+#define EXP2_08_PIN -1
+
+//
+// Onboard SD card
+// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
+//
+#if SD_CONNECTION_IS(LCD)
+ #define SDSS EXP2_04_PIN
+ #define SD_SS_PIN SDSS
+ #define SD_SCK_PIN EXP2_02_PIN
+ #define SD_MISO_PIN EXP2_01_PIN
+ #define SD_MOSI_PIN EXP2_06_PIN
+ #define SD_DETECT_PIN EXP2_07_PIN
+#elif SD_CONNECTION_IS(ONBOARD)
+ #define SD_DETECT_PIN PE8
+ #define SD_SCK_PIN PB13
+ #define SD_MISO_PIN PB14
+ #define SD_MOSI_PIN PB11
+ #define ONBOARD_SD_CS_PIN PB14 // Chip select for "System" SD card
+ #define SD_SS_PIN ONBOARD_SD_CS_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+ #error "No custom SD drive cable defined for this board."
+#endif
+
+//
+// LCDs and Controllers
+//
+#if IS_TFTGLCD_PANEL
+
+ #if ENABLED(TFTGLCD_PANEL_SPI)
+ #define TFTGLCD_CS EXP2_03_PIN
+ #endif
+
+#elif HAS_WIRED_LCD
+
+ #define BEEPER_PIN EXP1_01_PIN
+ #define BTN_ENC EXP1_02_PIN
+
+ #if ENABLED(CR10_STOCKDISPLAY)
+
+ #define LCD_PINS_RS EXP1_07_PIN
+
+ #define BTN_EN1 EXP1_03_PIN
+ #define BTN_EN2 EXP1_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_08_PIN
+ #define LCD_PINS_D4 EXP1_06_PIN
+
+ #elif ENABLED(MKS_MINI_12864)
+
+ #define DOGLCD_A0 EXP1_07_PIN
+ #define DOGLCD_CS EXP1_06_PIN
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #else
+
+ #define LCD_PINS_RS EXP1_04_PIN
+
+ #define BTN_EN1 EXP2_03_PIN
+ #define BTN_EN2 EXP2_05_PIN
+
+ #define LCD_PINS_ENABLE EXP1_03_PIN
+ #define LCD_PINS_D4 EXP1_05_PIN
+
+ #if ENABLED(FYSETC_MINI_12864)
+ #define DOGLCD_CS EXP1_03_PIN
+ #define DOGLCD_A0 EXP1_04_PIN
+ //#define LCD_BACKLIGHT_PIN -1
+
+ #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
+ // results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+ #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally.
+ #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+ #ifndef RGB_LED_R_PIN
+ #define RGB_LED_R_PIN EXP1_06_PIN
+ #endif
+ #ifndef RGB_LED_G_PIN
+ #define RGB_LED_G_PIN EXP1_07_PIN
+ #endif
+ #ifndef RGB_LED_B_PIN
+ #define RGB_LED_B_PIN EXP1_08_PIN
+ #endif
+ #elif ENABLED(FYSETC_MINI_12864_2_1)
+ #define NEOPIXEL_PIN EXP1_06_PIN
+ #endif
+ #endif // !FYSETC_MINI_12864
+
+ #if IS_ULTIPANEL
+ #define LCD_PINS_D5 EXP1_06_PIN
+ #define LCD_PINS_D6 EXP1_07_PIN
+ #define LCD_PINS_D7 EXP1_08_PIN
+
+ #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+ #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
+ #endif
+
+ #endif
+
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+// Alter timing for graphical display
+#if IS_U8GLIB_ST7920
+ #ifndef BOARD_ST7920_DELAY_1
+ #define BOARD_ST7920_DELAY_1 120
+ #endif
+ #ifndef BOARD_ST7920_DELAY_2
+ #define BOARD_ST7920_DELAY_2 80
+ #endif
+ #ifndef BOARD_ST7920_DELAY_3
+ #define BOARD_ST7920_DELAY_3 580
+ #endif
+#endif
diff --git a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h
index f931d9924acfd..f71b7b40ebd19 100644
--- a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h
+++ b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h
@@ -21,6 +21,8 @@
*/
#pragma once
+#include "env_validate.h"
+
//#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4
#ifndef BOARD_INFO_NAME
diff --git a/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json b/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json
new file mode 100644
index 0000000000000..a3ac6ea6793a5
--- /dev/null
+++ b/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json
@@ -0,0 +1,47 @@
+{
+ "build": {
+ "core": "stm32",
+ "cpu": "cortex-m0plus",
+ "extra_flags": "-DSTM32G0xx -DSTM32G0B1xx",
+ "f_cpu": "64000000L",
+ "framework_extra_flags": {
+ "arduino": "-D__CORTEX_SC=0"
+ },
+ "mcu": "stm32g0b1vet6",
+ "product_line": "STM32G0B1xx",
+ "variant": "MARLIN_G0B1VE"
+ },
+ "debug": {
+ "default_tools": [
+ "stlink"
+ ],
+ "jlink_device": "STM32G0B1VE",
+ "onboard_tools": [
+ "stlink"
+ ],
+ "openocd_target": "stm32g0x",
+ "svd_path": "STM32G0B1.svd"
+ },
+ "frameworks": [
+ "arduino",
+ "cmsis",
+ "libopencm3",
+ "stm32cube",
+ "zephyr"
+ ],
+ "name": "STM32G0B1VE",
+ "upload": {
+ "maximum_ram_size": 147456,
+ "maximum_size": 524288,
+ "protocol": "stlink",
+ "protocols": [
+ "stlink",
+ "jlink",
+ "cmsis-dap",
+ "blackmagic",
+ "mbed"
+ ]
+ },
+ "url": "https://www.st.com/content/st_com/en/products/microcontrollers-microprocessors/stm32-32-bit-arm-cortex-mcus/stm32-mainstream-mcus/stm32g0-series/stm32g0x1.html",
+ "vendor": "ST"
+}
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c
index eb95de1495f72..3187367a2d997 100644
--- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c
@@ -218,6 +218,7 @@ WEAK const PinMap PinMap_UART_TX[] = {
{PC_12, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
{PD_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
{PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
{PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)},
{NC, NP, 0}
};
@@ -252,6 +253,7 @@ WEAK const PinMap PinMap_UART_RX[] = {
{PC_11_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)},
{PD_2, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
{PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
{NC, NP, 0}
};
#endif
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp
index d18509f35f712..fa4ebfa713293 100644
--- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp
@@ -130,14 +130,7 @@ WEAK void SystemClock_Config(void)
RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
// Reset clock registers (in case bootloader has changed them)
- RCC->CR |= RCC_CR_HSION;
- while (!(RCC->CR & RCC_CR_HSIRDY))
- ;
- RCC->CFGR = 0x00000000;
- RCC->CR = RCC_CR_HSION;
- while (RCC->CR & RCC_CR_PLLRDY)
- ;
- RCC->PLLCFGR = 0x00001000;
+ SystemInit();
/** Configure the main internal regulator output voltage
*/
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h
index 6a26baff45dbb..23cecd371a289 100644
--- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h
@@ -158,6 +158,9 @@
#endif
// UART Definitions
+//#define ENABLE_HWSERIAL1 done automatically by the #define SERIAL_UART_INSTANCE below
+#define ENABLE_HWSERIAL3
+
#ifndef SERIAL_UART_INSTANCE
#define SERIAL_UART_INSTANCE 2
#endif
@@ -171,6 +174,15 @@
#define PIN_SERIAL_TX PA2
#endif
+// Optional PIN_SERIALn_RX and PIN_SERIALn_TX where 'n' is the U(S)ART number
+// Used when user instantiate a hardware Serial using its peripheral name.
+// Example: HardwareSerial mySerial(USART3);
+// will use PIN_SERIAL3_RX and PIN_SERIAL3_TX if defined.
+#define PIN_SERIAL1_RX PA3
+#define PIN_SERIAL1_TX PA2
+#define PIN_SERIAL3_RX PD9
+#define PIN_SERIAL3_TX PD8
+
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c
new file mode 100644
index 0000000000000..a6b1e44237188
--- /dev/null
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c
@@ -0,0 +1,480 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2020-2021, STMicroelectronics
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ *******************************************************************************
+ */
+/*
+ * Automatically generated from STM32G0B1V(B-C-E)Ix.xml, STM32G0B1V(B-C-E)Tx.xml
+ * STM32G0B1V(C-E)Ix.xml, STM32G0B1V(C-E)Tx.xml
+ * STM32G0C1V(C-E)Ix.xml, STM32G0C1V(C-E)Tx.xml
+ * CubeMX DB release 6.0.30
+ */
+#if !defined(CUSTOM_PERIPHERAL_PINS)
+#include "Arduino.h"
+#include "PeripheralPins.h"
+
+/* =====
+ * Notes:
+ * - The pins mentioned Px_y_ALTz are alternative possibilities which use other
+ * HW peripheral instances. You can use them the same way as any other "normal"
+ * pin (i.e. analogWrite(PA7_ALT1, 128);).
+ *
+ * - Commented lines are alternative possibilities which are not used per default.
+ * If you change them, you will have to know what you do
+ * =====
+ */
+
+//*** ADC ***
+
+#ifdef HAL_ADC_MODULE_ENABLED
+WEAK const PinMap PinMap_ADC[] = {
+ {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
+ {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
+ {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
+ {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
+ {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
+ {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
+ {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
+ {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
+ {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
+ {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
+ {PB_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
+ {PB_10, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
+ {PB_11, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
+ {PB_12, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // ADC1_IN16
+ {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)}, // ADC1_IN17
+ {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC1_IN18
+ {NC, NP, 0}
+};
+#endif
+
+//*** DAC ***
+
+#ifdef HAL_DAC_MODULE_ENABLED
+WEAK const PinMap PinMap_DAC[] = {
+ {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC1_OUT1
+ {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC1_OUT2
+ {NC, NP, 0}
+};
+#endif
+
+//*** I2C ***
+
+#ifdef HAL_I2C_MODULE_ENABLED
+WEAK const PinMap PinMap_I2C_SDA[] = {
+ {PA_6, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_6_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)},
+ {PA_10, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PA_10_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_10_R, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PA_10_R_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_12, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PB_4, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PB_4_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)},
+ {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PB_14, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PC_1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_I2C_MODULE_ENABLED
+WEAK const PinMap PinMap_I2C_SCL[] = {
+ {PA_7, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_7_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)},
+ {PA_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PA_9_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_9_R, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PA_9_R_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PA_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)},
+ {PB_3_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)},
+ {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)},
+ {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PB_13, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)},
+ {PC_0, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** TIM ***
+
+#ifdef HAL_TIM_MODULE_ENABLED
+WEAK const PinMap PinMap_TIM[] = {
+ {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+ {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2
+ {PA_1_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)}, // TIM15_CH1N
+ {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3
+ {PA_2_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 0)}, // TIM15_CH1
+ {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4
+ {PA_3_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 2, 0)}, // TIM15_CH2
+ {PA_4, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1
+ {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+ {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+ {PA_6_ALT1, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM16, 1, 0)}, // TIM16_CH1
+ {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N
+ {PA_7_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+ {PA_7_ALT2, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1
+ {PA_7_ALT3, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM17, 1, 0)}, // TIM17_CH1
+ {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1
+ {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2
+ {PA_9_R, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2
+ {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3
+ {PA_10_R, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3
+ {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4
+ {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+ {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N
+ {PB_0_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3
+ {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N
+ {PB_1_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4
+ {PB_1_ALT2, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM14, 1, 0)}, // TIM14_CH1
+ {PB_3, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
+ {PB_3_ALT1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2
+ {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+ {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+ {PB_6, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
+ {PB_6_ALT1, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 1, 0)}, // TIM4_CH1
+ {PB_6_ALT2, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 1)}, // TIM16_CH1N
+ {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 2, 0)}, // TIM4_CH2
+ {PB_7_ALT1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 1)}, // TIM17_CH1N
+ {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 3, 0)}, // TIM4_CH3
+ {PB_8_ALT1, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1
+ {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 4, 0)}, // TIM4_CH4
+ {PB_9_ALT1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1
+ {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3
+ {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4
+ {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N
+ {PB_13_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)}, // TIM15_CH1N
+ {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N
+ {PB_14_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 0)}, // TIM15_CH1
+ {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N
+ {PB_15_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM15, 1, 1)}, // TIM15_CH1N
+ {PB_15_ALT2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 2, 0)}, // TIM15_CH2
+ {PC_1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 1, 0)}, // TIM15_CH1
+ {PC_2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 2, 0)}, // TIM15_CH2
+ {PC_4, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+ {PC_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2
+ {PC_6, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3
+ {PC_6_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+ {PC_7, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4
+ {PC_7_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+ {PC_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1
+ {PC_8_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3
+ {PC_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2
+ {PC_9_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4
+ {PC_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3
+ {PC_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4
+ {PC_12, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM14, 1, 0)}, // TIM14_CH1
+ {PD_0, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1
+ {PD_1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1
+ {PD_2, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N
+ {PD_3, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N
+ {PD_4, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N
+ {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
+ {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
+ {PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
+ {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
+ {PE_0, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM16, 1, 0)}, // TIM16_CH1
+ {PE_1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM17, 1, 0)}, // TIM17_CH1
+ {PE_3, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+ {PE_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+ {PE_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3
+ {PE_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4
+ {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
+ {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
+ {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
+ {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
+ {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
+ {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
+ {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
+ {PF_0, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM14, 1, 0)}, // TIM14_CH1
+ {PF_1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 1, 1)}, // TIM15_CH1N
+ {PF_12, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 1, 0)}, // TIM15_CH1
+ {PF_13, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 2, 0)}, // TIM15_CH2
+ {NC, NP, 0}
+};
+#endif
+
+//*** UART ***
+
+#ifdef HAL_UART_MODULE_ENABLED
+WEAK const PinMap PinMap_UART_TX[] = {
+ {PA_0, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+ {PA_2, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)},
+ {PA_2_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PA_4, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {PA_5, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_9_R, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_14, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PA_14_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PB_0, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)},
+ {PB_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PB_6, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PB_6_ALT1, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+ {PB_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_8_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+ {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_11, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PC_0, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PC_0_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART6)},
+ {PC_1, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PC_4, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PC_4_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PC_6, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PC_10_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)},
+ {PC_12, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PD_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PE_8, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)},
+ {PE_10, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)},
+ {PF_4, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PF_9, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+WEAK const PinMap PinMap_UART_RX[] = {
+ {PA_1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+ {PA_3, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)},
+ {PA_3_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PA_5, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_10_R, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_13, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PA_15, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PB_0, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)},
+ {PB_4, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PB_7, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PB_7_ALT1, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+ {PB_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_9_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+ {PB_10, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PB_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PC_0, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PC_1, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PC_1_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART6)},
+ {PC_5, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PC_5_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PC_7, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PC_11_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)},
+ {PD_2, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PE_9, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)},
+ {PE_11, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PF_3, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)},
+ {PF_5, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PF_10, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+WEAK const PinMap PinMap_UART_RTS[] = {
+ {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PA_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_15, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_USART3)},
+ {PA_15_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+ {PB_1, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)},
+ {PB_1_ALT1, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PB_1_ALT2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_3, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},
+ {PB_5, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)},
+ {PB_12, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_14_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+ {PC_9, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PD_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_4_ALT1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PD_12, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PD_15, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)},
+ {PE_7, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PF_3, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {PF_6, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PF_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+WEAK const PinMap PinMap_UART_CTS[] = {
+ {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PA_6, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)},
+ {PA_6_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PA_6_ALT2, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PB_0, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)},
+ {PB_4, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},
+ {PB_6, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)},
+ {PB_7, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+ {PB_13, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PB_13_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PB_15, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
+ {PC_8, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)},
+ {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)},
+ {PD_5, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PD_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)},
+ {PD_14, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)},
+ {PF_7, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)},
+ {PF_7_ALT1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)},
+ {PF_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** SPI ***
+
+#ifdef HAL_SPI_MODULE_ENABLED
+WEAK const PinMap PinMap_SPI_MOSI[] = {
+ {PA_2, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PA_10_R, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PA_12, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_5_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)},
+ {PB_7, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PB_11, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)},
+ {PD_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PD_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)},
+ {PE_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+WEAK const PinMap PinMap_SPI_MISO[] = {
+ {PA_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)},
+ {PA_9_R, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)},
+ {PA_11, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_4_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)},
+ {PB_6, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)},
+ {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)},
+ {PD_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PD_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)},
+ {PE_14, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+WEAK const PinMap PinMap_SPI_SCLK[] = {
+ {PA_0, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PA_1, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_3_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)},
+ {PB_8, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+ {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)},
+ {PD_1, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PD_8, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)},
+ {PE_13, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+WEAK const PinMap PinMap_SPI_SSEL[] = {
+ {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_4_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)},
+ {PA_8, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_15_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)},
+ {PB_0, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+ {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PD_0, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {PD_9, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)},
+ {PE_12, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** FDCAN ***
+
+#ifdef HAL_FDCAN_MODULE_ENABLED
+WEAK const PinMap PinMap_CAN_RD[] = {
+ {PA_11, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PB_0, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PB_5, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PB_8, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PB_12, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PC_2, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PC_4, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_0, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_12, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_14, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_FDCAN_MODULE_ENABLED
+WEAK const PinMap PinMap_CAN_TD[] = {
+ {PA_12, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PB_1, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PB_6, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PB_9, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PB_13, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PC_3, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {PC_5, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_1, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_13, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)},
+ {PD_15, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** No ETHERNET ***
+
+//*** No QUADSPI ***
+
+//*** USB ***
+
+#if defined(HAL_PCD_MODULE_ENABLED) || defined(HAL_HCD_MODULE_ENABLED)
+WEAK const PinMap PinMap_USB_DRD_FS[] = {
+ {PA_4, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE
+ {PA_11, USB_DRD_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DM
+ {PA_12, USB_DRD_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DP
+ {PA_13, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE
+ {PA_15, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USB)}, // USB_NOE
+ {PC_9, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USB)}, // USB_NOE
+ {NC, NP, 0}
+};
+#endif
+
+//*** No SD ***
+
+#endif /* !CUSTOM_PERIPHERAL_PINS */
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h
new file mode 100644
index 0000000000000..7d35869fe7ddf
--- /dev/null
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h
@@ -0,0 +1,91 @@
+/* Remap pin name */
+PA_9_R = PA_9 | PREMAP,
+PA_10_R = PA_10 | PREMAP,
+
+/* Alternate pin name */
+PA_1_ALT1 = PA_1 | ALT1,
+PA_2_ALT1 = PA_2 | ALT1,
+PA_3_ALT1 = PA_3 | ALT1,
+PA_4_ALT1 = PA_4 | ALT1,
+PA_6_ALT1 = PA_6 | ALT1,
+PA_6_ALT2 = PA_6 | ALT2,
+PA_7_ALT1 = PA_7 | ALT1,
+PA_7_ALT2 = PA_7 | ALT2,
+PA_7_ALT3 = PA_7 | ALT3,
+PA_9_ALT1 = PA_9 | ALT1,
+PA_9_R_ALT1 = PA_9_R | ALT1,
+PA_10_ALT1 = PA_10 | ALT1,
+PA_10_R_ALT1 = PA_10_R | ALT1,
+PA_14_ALT1 = PA_14 | ALT1,
+PA_15_ALT1 = PA_15 | ALT1,
+PB_0_ALT1 = PB_0 | ALT1,
+PB_1_ALT1 = PB_1 | ALT1,
+PB_1_ALT2 = PB_1 | ALT2,
+PB_3_ALT1 = PB_3 | ALT1,
+PB_4_ALT1 = PB_4 | ALT1,
+PB_5_ALT1 = PB_5 | ALT1,
+PB_6_ALT1 = PB_6 | ALT1,
+PB_6_ALT2 = PB_6 | ALT2,
+PB_7_ALT1 = PB_7 | ALT1,
+PB_8_ALT1 = PB_8 | ALT1,
+PB_9_ALT1 = PB_9 | ALT1,
+PB_13_ALT1 = PB_13 | ALT1,
+PB_14_ALT1 = PB_14 | ALT1,
+PB_15_ALT1 = PB_15 | ALT1,
+PB_15_ALT2 = PB_15 | ALT2,
+PC_0_ALT1 = PC_0 | ALT1,
+PC_1_ALT1 = PC_1 | ALT1,
+PC_4_ALT1 = PC_4 | ALT1,
+PC_5_ALT1 = PC_5 | ALT1,
+PC_6_ALT1 = PC_6 | ALT1,
+PC_7_ALT1 = PC_7 | ALT1,
+PC_8_ALT1 = PC_8 | ALT1,
+PC_9_ALT1 = PC_9 | ALT1,
+PC_10_ALT1 = PC_10 | ALT1,
+PC_11_ALT1 = PC_11 | ALT1,
+PD_4_ALT1 = PD_4 | ALT1,
+PF_7_ALT1 = PF_7 | ALT1,
+
+/* SYS_WKUP */
+#ifdef PWR_WAKEUP_PIN1
+ SYS_WKUP1 = PA_0,
+#endif
+#ifdef PWR_WAKEUP_PIN2
+ SYS_WKUP2 = PC_13,
+#endif
+#ifdef PWR_WAKEUP_PIN3
+ SYS_WKUP3 = PE_6,
+#endif
+#ifdef PWR_WAKEUP_PIN4
+ SYS_WKUP4 = PA_2,
+#endif
+#ifdef PWR_WAKEUP_PIN5
+ SYS_WKUP5 = PC_5,
+#endif
+#ifdef PWR_WAKEUP_PIN6
+ SYS_WKUP6 = PB_5,
+#endif
+#ifdef PWR_WAKEUP_PIN7
+ SYS_WKUP7 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN8
+ SYS_WKUP8 = NC,
+#endif
+
+/* USB */
+#ifdef USBCON
+ USB_DM = PA_11,
+ USB_DP = PA_12,
+ #ifdef USB_NOE_PA_4
+ USB_NOE = PA_4,
+ #endif
+ #ifdef USB_NOE_PA_13
+ USB_NOE = PA_13,
+ #endif
+ #ifdef USB_NOE_PA_15
+ USB_NOE = PA_15,
+ #endif
+ #ifdef USB_NOE_PC_9
+ USB_NOE = PC_9,
+ #endif
+#endif
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld
new file mode 100644
index 0000000000000..db07355fb7443
--- /dev/null
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld
@@ -0,0 +1,177 @@
+/**
+ ******************************************************************************
+ * @file LinkerScript.ld
+ * @author Auto-generated by STM32CubeIDE
+ * @brief Linker script for STM32G0B1VETx Device from STM32G0 series
+ * 512Kbytes FLASH
+ * 144Kbytes RAM
+ *
+ * Set heap size, stack size and stack location according
+ * to application requirements.
+ *
+ * Set memory bank area and size if external memory is used
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2020 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE
+ FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET
+}
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : {
+ . = ALIGN(4);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM : {
+ . = ALIGN(4);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(4);
+ } >FLASH
+
+ .preinit_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .init_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .fini_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp
new file mode 100644
index 0000000000000..8bf88aed49bfa
--- /dev/null
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp
@@ -0,0 +1,213 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2020-2021, STMicroelectronics
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ *******************************************************************************
+ */
+
+#if defined(STM32G0B1xx)
+#include "pins_arduino.h"
+
+// Digital PinName array
+const PinName digitalPin[] = {
+ PA_0, // D0/A0
+ PA_1, // D1/A1
+ PA_2, // D2/A2
+ PA_3, // D3/A3
+ PA_4, // D4/A4
+ PA_5, // D5/A5
+ PA_6, // D6/A6
+ PA_7, // D7/A7
+ PA_8, // D8
+ PA_9, // D9
+ PA_10, // D10
+ PA_11, // D11
+ PA_12, // D12
+ PA_13, // D13
+ PA_14, // D14
+ PA_15, // D15
+ PB_0, // D16/A8
+ PB_1, // D17/A9
+ PB_2, // D18/A10
+ PB_3, // D19
+ PB_4, // D20
+ PB_5, // D21
+ PB_6, // D22
+ PB_7, // D23
+ PB_8, // D24
+ PB_9, // D25
+ PB_10, // D26/A11
+ PB_11, // D27/A12
+ PB_12, // D28/A13
+ PB_13, // D29
+ PB_14, // D30
+ PB_15, // D31
+ PC_0, // D32
+ PC_1, // D33
+ PC_2, // D34
+ PC_3, // D35
+ PC_4, // D36/A14
+ PC_5, // D37/A15
+ PC_6, // D38
+ PC_7, // D39
+ PC_8, // D40
+ PC_9, // D41
+ PC_10, // D42
+ PC_11, // D43
+ PC_12, // D44
+ PC_13, // D45
+ PC_14, // D46
+ PC_15, // D47
+ PD_0, // D48
+ PD_1, // D49
+ PD_2, // D50
+ PD_3, // D51
+ PD_4, // D52
+ PD_5, // D53
+ PD_6, // D54
+ PD_7, // D55
+ PD_8, // D56
+ PD_9, // D57
+ PD_10, // D58
+ PD_11, // D59
+ PD_12, // D60
+ PD_13, // D61
+ PD_14, // D62
+ PD_15, // D63
+ PE_0, // D64
+ PE_1, // D65
+ PE_2, // D66
+ PE_3, // D67
+ PE_4, // D68
+ PE_5, // D69
+ PE_6, // D70
+ PE_7, // D71
+ PE_8, // D72
+ PE_9, // D73
+ PE_10, // D74
+ PE_11, // D75
+ PE_12, // D76
+ PE_13, // D77
+ PE_14, // D78
+ PE_15, // D79
+ PF_0, // D80
+ PF_1, // D81
+ PF_2, // D82
+ PF_3, // D83
+ PF_4, // D84
+ PF_5, // D85
+ PF_6, // D86
+ PF_7, // D87
+ PF_8, // D88
+ PF_9, // D89
+ PF_10, // D90
+ PF_11, // D91
+ PF_12, // D92
+ PF_13, // D93
+ PA_9_R, // D94
+ PA_10_R // D95
+};
+
+// Analog (Ax) pin number array
+const uint32_t analogInputPin[] = {
+ 0, // A0, PA0
+ 1, // A1, PA1
+ 2, // A2, PA2
+ 3, // A3, PA3
+ 4, // A4, PA4
+ 5, // A5, PA5
+ 6, // A6, PA6
+ 7, // A7, PA7
+ 16, // A8, PB0
+ 17, // A9, PB1
+ 18, // A10, PB2
+ 26, // A11, PB10
+ 27, // A12, PB11
+ 28, // A13, PB12
+ 36, // A14, PC4
+ 37 // A15, PC5
+};
+
+// ----------------------------------------------------------------------------
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follows :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 64000000
+ * HCLK(Hz) = 64000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 1
+ * PLL_M = 1
+ * PLL_N = 24
+ * PLL_R = 3
+ * PLL_P = 2
+ * PLL_Q = 4
+ * USB(Hz) = 48000000 (PLLQ)
+ * @param None
+ * @retval None
+ */
+WEAK void SystemClock_Config(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+ RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+ RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+ // Reset clock registers (in case bootloader has changed them)
+ SystemInit();
+
+ /** Configure the main internal regulator output voltage
+ */
+ HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+ /** Initializes the RCC Oscillators according to the specified parameters
+ * in the RCC_OscInitTypeDef structure.
+ */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1;
+ RCC_OscInitStruct.PLL.PLLN = 24;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV4;
+ RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV3;
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+ {
+ Error_Handler();
+ }
+ /** Initializes the CPU, AHB and APB buses clocks
+ */
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+ |RCC_CLOCKTYPE_PCLK1;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
+ {
+ Error_Handler();
+ }
+ /** Initializes the peripherals clocks
+ */
+ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL;
+ if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+ {
+ Error_Handler();
+ }
+}
+
+#ifdef __cplusplus
+}
+#endif
+#endif /* STM32G0B1xx */
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h
new file mode 100644
index 0000000000000..e6f2251db0595
--- /dev/null
+++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h
@@ -0,0 +1,258 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2020-2021, STMicroelectronics
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ *******************************************************************************
+ */
+#pragma once
+
+/*----------------------------------------------------------------------------
+ * STM32 pins number
+ *----------------------------------------------------------------------------*/
+#define PA0 PIN_A0
+#define PA1 PIN_A1
+#define PA2 PIN_A2
+#define PA3 PIN_A3
+#define PA4 PIN_A4
+#define PA5 PIN_A5
+#define PA6 PIN_A6
+#define PA7 PIN_A7
+#define PA8 8
+#define PA9 9
+#define PA10 10
+#define PA11 11
+#define PA12 12
+#define PA13 13
+#define PA14 14
+#define PA15 15
+#define PB0 PIN_A8
+#define PB1 PIN_A9
+#define PB2 PIN_A10
+#define PB3 19
+#define PB4 20
+#define PB5 21
+#define PB6 22
+#define PB7 23
+#define PB8 24
+#define PB9 25
+#define PB10 PIN_A11
+#define PB11 PIN_A12
+#define PB12 PIN_A13
+#define PB13 29
+#define PB14 30
+#define PB15 31
+#define PC0 32
+#define PC1 33
+#define PC2 34
+#define PC3 35
+#define PC4 PIN_A14
+#define PC5 PIN_A15
+#define PC6 38
+#define PC7 39
+#define PC8 40
+#define PC9 41
+#define PC10 42
+#define PC11 43
+#define PC12 44
+#define PC13 45
+#define PC14 46
+#define PC15 47
+#define PD0 48
+#define PD1 49
+#define PD2 50
+#define PD3 51
+#define PD4 52
+#define PD5 53
+#define PD6 54
+#define PD7 55
+#define PD8 56
+#define PD9 57
+#define PD10 58
+#define PD11 59
+#define PD12 60
+#define PD13 61
+#define PD14 62
+#define PD15 63
+#define PE0 64
+#define PE1 65
+#define PE2 66
+#define PE3 67
+#define PE4 68
+#define PE5 69
+#define PE6 70
+#define PE7 71
+#define PE8 72
+#define PE9 73
+#define PE10 74
+#define PE11 75
+#define PE12 76
+#define PE13 77
+#define PE14 78
+#define PE15 79
+#define PF0 80
+#define PF1 81
+#define PF2 82
+#define PF3 83
+#define PF4 84
+#define PF5 85
+#define PF6 86
+#define PF7 87
+#define PF8 88
+#define PF9 89
+#define PF10 90
+#define PF11 91
+#define PF12 92
+#define PF13 93
+#define PA9_R 94
+#define PA10_R 95
+
+// Alternate pins number
+#define PA1_ALT1 (PA1 | ALT1)
+#define PA2_ALT1 (PA2 | ALT1)
+#define PA3_ALT1 (PA3 | ALT1)
+#define PA4_ALT1 (PA4 | ALT1)
+#define PA6_ALT1 (PA6 | ALT1)
+#define PA6_ALT2 (PA6 | ALT2)
+#define PA7_ALT1 (PA7 | ALT1)
+#define PA7_ALT2 (PA7 | ALT2)
+#define PA7_ALT3 (PA7 | ALT3)
+#define PA9_ALT1 (PA9 | ALT1)
+#define PA9_R_ALT1 (PA9_R | ALT1)
+#define PA10_ALT1 (PA10 | ALT1)
+#define PA10_R_ALT1 (PA10_R | ALT1)
+#define PA14_ALT1 (PA14 | ALT1)
+#define PA15_ALT1 (PA15 | ALT1)
+#define PB0_ALT1 (PB0 | ALT1)
+#define PB1_ALT1 (PB1 | ALT1)
+#define PB1_ALT2 (PB1 | ALT2)
+#define PB3_ALT1 (PB3 | ALT1)
+#define PB4_ALT1 (PB4 | ALT1)
+#define PB5_ALT1 (PB5 | ALT1)
+#define PB6_ALT1 (PB6 | ALT1)
+#define PB6_ALT2 (PB6 | ALT2)
+#define PB7_ALT1 (PB7 | ALT1)
+#define PB8_ALT1 (PB8 | ALT1)
+#define PB9_ALT1 (PB9 | ALT1)
+#define PB13_ALT1 (PB13 | ALT1)
+#define PB14_ALT1 (PB14 | ALT1)
+#define PB15_ALT1 (PB15 | ALT1)
+#define PB15_ALT2 (PB15 | ALT2)
+#define PC0_ALT1 (PC0 | ALT1)
+#define PC1_ALT1 (PC1 | ALT1)
+#define PC4_ALT1 (PC4 | ALT1)
+#define PC5_ALT1 (PC5 | ALT1)
+#define PC6_ALT1 (PC6 | ALT1)
+#define PC7_ALT1 (PC7 | ALT1)
+#define PC8_ALT1 (PC8 | ALT1)
+#define PC9_ALT1 (PC9 | ALT1)
+#define PC10_ALT1 (PC10 | ALT1)
+#define PC11_ALT1 (PC11 | ALT1)
+#define PD4_ALT1 (PD4 | ALT1)
+#define PF7_ALT1 (PF7 | ALT1)
+
+#define NUM_DIGITAL_PINS 96
+#define NUM_REMAP_PINS 2
+#define NUM_ANALOG_INPUTS 16
+
+// On-board LED pin number
+#ifndef LED_BUILTIN
+ #define LED_BUILTIN PNUM_NOT_DEFINED
+#endif
+
+// On-board user button
+#ifndef USER_BTN
+ #define USER_BTN PNUM_NOT_DEFINED
+#endif
+
+// SPI definitions
+#ifndef PIN_SPI_SS
+ #define PIN_SPI_SS PA4
+#endif
+#ifndef PIN_SPI_SS1
+ #define PIN_SPI_SS1 PA15
+#endif
+#ifndef PIN_SPI_SS2
+ #define PIN_SPI_SS2 PB0
+#endif
+#ifndef PIN_SPI_SS3
+ #define PIN_SPI_SS3 PD9
+#endif
+#ifndef PIN_SPI_MOSI
+ #define PIN_SPI_MOSI PA2
+#endif
+#ifndef PIN_SPI_MISO
+ #define PIN_SPI_MISO PA6
+#endif
+#ifndef PIN_SPI_SCK
+ #define PIN_SPI_SCK PA1
+#endif
+
+// I2C definitions
+#ifndef PIN_WIRE_SDA
+ #define PIN_WIRE_SDA PA6
+#endif
+#ifndef PIN_WIRE_SCL
+ #define PIN_WIRE_SCL PA7
+#endif
+
+// Timer Definitions
+// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin
+#ifndef TIMER_TONE
+ #define TIMER_TONE TIM6
+#endif
+#ifndef TIMER_SERVO
+ #define TIMER_SERVO TIM7
+#endif
+
+// UART Definitions
+#ifndef SERIAL_UART_INSTANCE
+ #define SERIAL_UART_INSTANCE 4
+#endif
+
+// Default pin used for generic 'Serial' instance
+// Mandatory for Firmata
+#ifndef PIN_SERIAL_RX
+ #define PIN_SERIAL_RX PA1
+#endif
+#ifndef PIN_SERIAL_TX
+ #define PIN_SERIAL_TX PA0
+#endif
+
+// Extra HAL modules
+#if !defined(HAL_DAC_MODULE_DISABLED)
+ #define HAL_DAC_MODULE_ENABLED
+#endif
+
+/*----------------------------------------------------------------------------
+ * Arduino objects - C++ only
+ *----------------------------------------------------------------------------*/
+
+#ifdef __cplusplus
+ // These serial port names are intended to allow libraries and architecture-neutral
+ // sketches to automatically default to the correct port name for a particular type
+ // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
+ // the first hardware serial port whose RX/TX pins are not dedicated to another use.
+ //
+ // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
+ //
+ // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
+ //
+ // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
+ //
+ // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
+ //
+ // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
+ // pins are NOT connected to anything by default.
+ #ifndef SERIAL_PORT_MONITOR
+ #define SERIAL_PORT_MONITOR Serial
+ #endif
+ #ifndef SERIAL_PORT_HARDWARE
+ #define SERIAL_PORT_HARDWARE Serial
+ #endif
+#endif
diff --git a/ini/stm32g0.ini b/ini/stm32g0.ini
index 568d9c8e9f019..c8554741bceb0 100644
--- a/ini/stm32g0.ini
+++ b/ini/stm32g0.ini
@@ -41,7 +41,7 @@ upload_protocol = stlink
debug_tool = stlink
#
-# BigTreeTech SKR mini E3 V3.0 (STM32G0B1RET6 ARM Cortex-M0+)
+# BigTreeTech SKR Mini E3 V3.0 / Manta E3 EZ V1.0 / Manta M4P V1.0 / Manta M5P V1.0 (STM32G0B1RET6 ARM Cortex-M0+)
#
[env:STM32G0B1RE_btt]
extends = stm32_variant
@@ -59,6 +59,7 @@ upload_protocol = stlink
debug_tool = stlink
#
+# BigTreeTech SKR Mini E3 V3.0 / Manta E3 EZ V1.0 / Manta M4P V1.0 / Manta M5P V1.0 (STM32G0B1RET6 ARM Cortex-M0+)
# Custom upload to SD via Marlin with Binary Protocol
#
[env:STM32G0B1RE_btt_xfer]
@@ -67,3 +68,33 @@ build_flags = ${env:STM32G0B1RE_btt.build_flags} -DXFER_BUILD
extra_scripts = ${env:STM32G0B1RE_btt.extra_scripts}
pre:buildroot/share/scripts/upload.py
upload_protocol = custom
+
+#
+# BigTreeTech Manta M8P V1.x (STM32G0B1VET6 ARM Cortex-M0+)
+#
+[env:STM32G0B1VE_btt]
+extends = stm32_variant
+platform = ststm32@~14.1.0
+platform_packages = framework-arduinoststm32@https://github.com/stm32duino/Arduino_Core_STM32/archive/main.zip
+board = marlin_STM32G0B1VE
+board_build.offset = 0x2000
+board_upload.offset_address = 0x08002000
+build_flags = ${stm32_variant.build_flags}
+ -DPIN_SERIAL4_RX=PE_9 -DPIN_SERIAL4_TX=PE_8
+ -DPIN_SERIAL5_RX=PE_11 -DPIN_SERIAL5_TX=PE_10
+ -DSERIAL_RX_BUFFER_SIZE=1024 -DSERIAL_TX_BUFFER_SIZE=1024
+ -DTIMER_SERVO=TIM3 -DTIMER_TONE=TIM4
+ -DSTEP_TIMER_IRQ_PRIO=0
+upload_protocol = stlink
+debug_tool = stlink
+
+#
+# BigTreeTech Manta M8P V1.x (STM32G0B1VET6 ARM Cortex-M0+)
+# Custom upload to SD via Marlin with Binary Protocol
+#
+[env:STM32G0B1VE_btt_xfer]
+extends = env:STM32G0B1VE_btt
+build_flags = ${env:STM32G0B1VE_btt.build_flags} -DXFER_BUILD
+extra_scripts = ${env:STM32G0B1VE_btt.extra_scripts}
+ pre:buildroot/share/scripts/upload.py
+upload_protocol = custom