diff --git a/locales/en/messages.json b/locales/en/messages.json index 5c39013a55b..2e498ac51f6 100755 --- a/locales/en/messages.json +++ b/locales/en/messages.json @@ -691,7 +691,7 @@ "message": "Contributing" }, "defaultContributingText": { - "message": "If you would like to help make Betaflight even better you can help in many ways, including:
" + "message": "If you would like to help make Betaflight even better you can help in many ways, including:
" }, "defaultFacebookText": { "message": "We also have a Facebook Group.
Join us to get a place to talk about Betaflight, ask configuration questions, or just hang out with fellow pilots." @@ -731,10 +731,10 @@ "message": "Documentation / Manual" }, "defaultDocumentation": { - "message": "Betaflight documentation is available in release notes and wiki.

" + "message": "Betaflight documentation is available in release notes and support.

" }, "defaultDocumentation1": { - "message": "The Betaflight wiki is a great resource for information, it can be found here." + "message": "Betaflight support is a great resource for information, it can be found here." }, "defaultDocumentation2": { "message": "The release notes for the firmware can be read at GitHub releases page, here." @@ -749,13 +749,13 @@ "message": "Developer" }, "defaultSupport": { - "message": "For support please search the forums and wiki first or contact your vendor.

" + "message": "For support please search the forums and support first or contact your vendor.

" }, "defaultSupport1": { "message": "RC Groups thread" }, "defaultSupport2": { - "message": "Betaflight Wiki" + "message": "Betaflight Support" }, "defaultSupport3": { "message": "Joshua Bardwell Betaflight 4.3 Videos" @@ -943,7 +943,7 @@ "message": "Arming Allowed" }, "initialSetupArmingDisableFlagsTooltip": { - "message": "List of flags indicating why arming is currently not allowed. Pass the mouse over the flag or refer to the Wiki ('Arming Sequence & Safety' page) for more info." + "message": "List of flags indicating why arming is currently not allowed. Pass the mouse over the flag or refer to the Support ('Arming Sequence & Safety' page) for more info." }, "initialSetupArmingDisableFlagsTooltipNO_GYRO": { "message": "A gyro was not detected", @@ -3034,7 +3034,7 @@ "message": "Safety notice
Remove all propellers to prevent injury!
The motors will spin up!" }, "motorsRemapDialogExplanations": { - "message": "Information notice
Motors will spin up one by one and you will be able to select which motor is spinning. The battery should be plugged in, correct ESC protocol should be selected. This utility can only re-arrange currently active motors. More complex re-mapping requires the CLI Resource command. Refer to this Wiki page." + "message": "Information notice
Motors will spin up one by one and you will be able to select which motor is spinning. The battery should be plugged in, correct ESC protocol should be selected. This utility can only re-arrange currently active motors. More complex re-mapping requires the CLI Resource command. Refer to this support page." }, "motorsRemapDialogSave": { "message": "Save" @@ -3106,7 +3106,7 @@ "message": "Feature works with DSHOT ESCs only.
Verify that your ESC (electric speed controller) supports DSHOT protocol and change it on $t(tabMotorTesting.message) tab." }, "escDshotDirectionDialog-WrongMixerText": { - "message": "Number of motors is 0.
Verify the current Mixer on $t(tabMotorTesting.message) tab or setup a custom one through CLI. Refer to this Wiki page." + "message": "Number of motors is 0.
Verify the current Mixer on $t(tabMotorTesting.message) tab or setup a custom one through CLI. Refer to this Support page." }, "escDshotDirectionDialog-WrongFirmwareText": { "message": "Update the firmware.
Make sure you are using the latest firmware: Betaflight 4.3 or newer." @@ -3569,7 +3569,7 @@ "message": "Recovery / Lost communication" }, "firmwareFlasherRecoveryText": { - "message": "If you have lost communication with your board follow these steps to restore communication: " + "message": "If you have lost communication with your board follow these steps to restore communication: " }, "firmwareFlasherButtonLeave": { "message": "Leave Firmware Flasher" @@ -4506,7 +4506,7 @@ "message": "Vbat Sag Compensation" }, "pidTuningVbatSagCompensationHelp": { - "message": "Gives consistent throttle and PID performance over the usable battery voltage range by increasing motor output as battery voltage falls.

The amount of compensation can be varied between 0 and 100%. Full compensation (100%) is recommended.

Visit this wiki entry for more info." + "message": "Gives consistent throttle and PID performance over the usable battery voltage range by increasing motor output as battery voltage falls.

The amount of compensation can be varied between 0 and 100%. Full compensation (100%) is recommended.

Visit this support entry for more info." }, "pidTuningVbatSagValue": { "message": "%" @@ -4587,7 +4587,7 @@ "message": "Dynamic Idle Value [* 100 RPM]" }, "pidTuningIdleMinRpmHelp": { - "message": "Dynamic Idle improves control at low rpm and reduces risk of motor desyncs.

It improves PID authority, zero throttle stability, inverted hang time, and motor braking.

The Dynamic Idle min rpm should be set to around 3000 - 3500 rpm.

Visit this wiki entry for more info." + "message": "Dynamic Idle improves control at low rpm and reduces risk of motor desyncs.

It improves PID authority, zero throttle stability, inverted hang time, and motor braking.

The Dynamic Idle min rpm should be set to around 3000 - 3500 rpm.

Visit this support entry for more info." }, "pidTuningIdleMinRpmDisabled": { "message": "Dynamic Idle is DISABLED because Dshot Telemetry is OFF" @@ -4602,7 +4602,7 @@ "message": "Integrated Yaw" }, "pidTuningIntegratedYawCaution": { - "message": "CAUTION: if you enable this feature, you must adjust the YAW PID accordingly. More info here" + "message": "CAUTION: if you enable this feature, you must adjust the YAW PID accordingly. More info here" }, "pidTuningIntegratedYawHelp": { "message": "Integrated Yaw integrates yaw P, I and D values, allowing yaw P, I and D to be tuned a bit like you'd tune pitch and roll.

Very little I is required, because the integrated P acts like I, and integrated D acts like P.

NOTE: Integrated Yaw requires use of Absolute Control, since no I is needed with Integrated Yaw." @@ -6445,7 +6445,7 @@ "message": "Saved" }, "vtxHelp": { - "message": "Here you can configure the values for your Video Transmitter (VTX). You can view and change the transmission values, including the VTX Tables, if the flight controller and the VTX support it.
To set up your VTX use the following steps:
1. Go to this page;
2. Find the appropriate VTX configuration file for your country and your VTX model and download it;
3. Click '$t(vtxButtonLoadFile.message)' below, select the VTX configuration file, load it;
4. Verify that the settings are correct;
5. Click '$t(vtxButtonSave.message)' to store the VTX settings on the flight controller.
6. Optionally click '$t(vtxButtonSaveLua.message)' to save a lua configuration file you can use with the betaflight lua scripts (See more here.)", + "message": "Here you can configure the values for your Video Transmitter (VTX). You can view and change the transmission values, including the VTX Tables, if the flight controller and the VTX support it.
To set up your VTX use the following steps:
1. Go to this page;
2. Find the appropriate VTX configuration file for your country and your VTX model and download it;
3. Click '$t(vtxButtonLoadFile.message)' below, select the VTX configuration file, load it;
4. Verify that the settings are correct;
5. Click '$t(vtxButtonSave.message)' to store the VTX settings on the flight controller.
6. Optionally click '$t(vtxButtonSaveLua.message)' to save a lua configuration file you can use with the betaflight lua scripts (See more here.)", "description": "Introduction message in the VTX tab" }, "vtxMessageNotSupported": { @@ -6625,7 +6625,7 @@ "description": "Help for the number of power levels field of the VTX Table element in the VTX tab" }, "vtxTablePowerLevelsTableHelp": { - "message": "This table represents the different values of power that can be used for the VTX. They are divided into two:
- $t(vtxTablePowerLevelsValue.message): each power level requires a value that is defined by the hardware manufacturer. Ask your manufacturer for the correct value or consult the Betaflight wiki of VTX Tables to grab some samples.
- $t(vtxTablePowerLevelsLabel.message): you can put here the label you want for each power level value. It can be numbers (25, 200, 600, 1.2), letters (OFF, MIN, MAX) or a mix of them.

You must configure only the power levels that are legal at your country.", + "message": "This table represents the different values of power that can be used for the VTX. They are divided into two:
- $t(vtxTablePowerLevelsValue.message): each power level requires a value that is defined by the hardware manufacturer. Ask your manufacturer for the correct value or consult Betaflight support of VTX Tables to grab some samples.
- $t(vtxTablePowerLevelsLabel.message): you can put here the label you want for each power level value. It can be numbers (25, 200, 600, 1.2), letters (OFF, MIN, MAX) or a mix of them.

You must configure only the power levels that are legal at your country.", "description": "Help for the table of power levels (value-label) that appears in the VTX tab" }, "vtxTablePowerLevelsValue": { @@ -7218,9 +7218,9 @@ "message": "Cancel", "description": "Cancel button in the presets warning dialog" }, - "presetsWiki": { - "message": "Presets Wiki", - "description": "Button to open Presets Wiki link" + "presetsSupport": { + "message": "Presets Support", + "description": "Button to open Presets Support link" }, "presetsBackupSave": { "message": "Save backup", diff --git a/src/js/gui.js b/src/js/gui.js index 75b8d4927e3..6ad2fb6ecec 100644 --- a/src/js/gui.js +++ b/src/js/gui.js @@ -315,7 +315,7 @@ class GuiControl { $('div#content #button-documentation') .html(i18n.getMessage('betaflightSupportButton')) - .attr("href", `https://betaflight.com/docs/wiki/configurator/${tRex}-tab`); + .attr("href", `https://betaflight.com/docs/support/configurator/${tRex}-tab`); // loading tooltip $(function () { diff --git a/src/js/tabs/firmware_flasher.js b/src/js/tabs/firmware_flasher.js index af357c0459e..598235a320a 100644 --- a/src/js/tabs/firmware_flasher.js +++ b/src/js/tabs/firmware_flasher.js @@ -928,8 +928,8 @@ firmware_flasher.initialize = function (callback) { targetSupportInfo.on('click', function() { console.log('Support URL clicked:', self.selectedBoard); - let urlSupport = 'https://betaflight.com/docs/wiki/boards/missing'; // general board missing - const urlBoard = `https://betaflight.com/docs/wiki/boards/${self.selectedBoard}`; // board description + let urlSupport = 'https://betaflight.com/docs/support/boards/missing'; // general board missing + const urlBoard = `https://betaflight.com/docs/support/boards/${self.selectedBoard}`; // board description if (urlExists(urlBoard)) { urlSupport = urlBoard; } diff --git a/src/tabs/presets/presets.html b/src/tabs/presets/presets.html index 5b5873cfa28..64abf7761a8 100644 --- a/src/tabs/presets/presets.html +++ b/src/tabs/presets/presets.html @@ -3,7 +3,7 @@
- Presets Wiki + Presets Support
diff --git a/src/tabs/presets/presets.less b/src/tabs/presets/presets.less index 279e9c0d60d..8a518ba11f2 100644 --- a/src/tabs/presets/presets.less +++ b/src/tabs/presets/presets.less @@ -134,7 +134,7 @@ font-size: 10px; height: 17px; } -.presetsWikiButton { +.presetsSupportButton { margin-right: 0px; } #presets_list {