Skip to content

Latest commit

 

History

History
132 lines (86 loc) · 5.32 KB

Nema11DRV8825.md

File metadata and controls

132 lines (86 loc) · 5.32 KB
Raw

Bipolar Nema11 Stepper motor with DRV8825 Driver Carrier

ScreenShot Nema ScreenShot DRV8825

Hardware

Nema 11 Stepper Motor:

see A4988 Nema Section

DRV8825:

Info.

DRV8825 at pololu

DRV8825 Datasheet

The DRV8825 is a very common and inexpensive stepper motor controller, designed by pololu. Other than the controller and motor it only requires one other part, a decoupling capacitor that is mounted physically close to the controller.
With a heatsink the device can handle up to 1.5 amps per coil. Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

Pinout of the DRV8825 module:

ScreenShot DRV8825 pinout

We see the following pins:

  • VMOT – The motor DC supply voltage (positive). The maximum voltage is 35 volts.
  • GND – The motor supply voltage ground.
  • 2B, 2A – The connections to coil 2 of the bipolar stepper motor.
  • 1A, 1B – The connections to coil 1 of the bipolar stepper motor.
  • GND – The logic supply ground.
  • FLT - Logic low when in fault condition (overtemp, overcurrent)
  • ENABLE – Logic high to disable device outputs and indexer operation, logic low to enable. Internal pulldown.
  • MS0, MS1, MS2 – These three connections determine the microstepping mode of the DRV8825 module. By setting the logic levels here you can set the motor to Full, Half, Quarter, Eighth, Sixteenth or 1/32 steps.
  • RESET – Active-low reset input initializes the indexer logic and disables the H-bridge outputs. Internal pulldown.
  • SLEEP – Logic high to enable device, logic low to enter low-power sleep Internal pulldown.
  • STEP – This is how you drive the motor from an external microcontroller or square wave oscillator. Each pulse sent here steps the motor by whatever number of steps or microsteps that has been set by MSX settings. The faster you pulse this the faster the motor will travel.
  • DIR – The direction control A high input here drives the motor clockwise, a low will drive it counterclockwise.

DRV8825 wiring diagram:

ScreenShot DRV8825 wiring diagram

Make sure to observe the motor connections, described in Motor section above the DRV8825 is conveniently laid out to match the 4-pin connector that is common on several bipolar motors but you should check your motor connections to be sure they are correct.

Connect 5 GPIO pins to MS0, MS1, MS2, STEP and DIR. NOTE in this figure MS pins are not connected.

Connect pi gnd to DRV8825 at GND. Connect Reset and sleep together and to pi 5V.

Note that there is an additional component not shown , in this circuit. This is essential to decouple the power supply. Any value from 47uf up will suffice, try and mount the capacitor as close to the DRV8825 VMOT and GND pins as possible. Connect up capacitor and Motor leads

Advisable to carry out a DRV8825 Current Adjustment before using motor see info links at top of section.

Also do not disconnect motor when in operation, as it will damage controller.

It is also possible and valid to connect up the DRV8825 in another alternative minimal wiring type as per A4988 section see first info links at top of section bottom of page.

ScreenShot DRV8825 mircostep data

There are 6 step modes for DRV8825, NOTE the DRV8825 only goes as far as 1/32 step Above is the step-resolution of Motor step per degree,

  • Full mode: 200 steps is one revolution. 1.8 degree per step = 360
  • Half mode: 400 steps is one revolution 0.9 degree per step = 360
  • ... and so on.

Resolution truth table used in code.

ScreenShot DRV8825 truth table data

Software

The library file RpiMotorLib.py contains the class which controls the motor. The class is called A4988Nema. This class handles both A4988 and Drv8825. The only difference from a user POV is when you instantiate the class the user passes the motor type and also user can now use 1/32 microstep for DRV8825.

See for more details A4988 software Section

Example: Should do a 180 degree turn. To run A stepper motor clockwise in Full mode for 100 steps. for step delay of .01 second. verbose output off , with 50mS init delay.

 
import RPi.GPIO as GPIO

# import the library
from RpiMotorLib import RpiMotorLib
    
#define GPIO pins
GPIO_pins = (14, 15, 18) # Microstep Resolution MS1-MS3 -> GPIO Pin
direction= 20       # Direction -> GPIO Pin
step = 21      # Step -> GPIO Pin

# Declare a instance of class pass GPIO pins numbers and the motor type
mymotortest = RpiMotorLib.A4988Nema(direction, step, GPIO_pins, "DRV8825")


# call the function, pass the arguments
mymotortest.motor_go(False, "Full" , 100, .01, False, .05)

# good practise to cleanup GPIO at some point before exit
GPIO.cleanup()