This repository provides Repo manifests to setup the Yocto build system for supported Gumstix products.
Note: If you already have a Yocto Project setup and want only the Gumstix BSP layer, use the meta-gumstix repository found here: git://github.com/gumstix/meta-gumstix.git.
The Yocto Project allows the creation of custom linux distributions for embedded systems, including Gumstix-based systems. It is a collection of git repositories known as layers each of which provides recipes to build software packages as well as configuration information.
Repo is a tool that enables the management of many git repositories given a single manifest file. Tell repo to fetch a manifest from this repository and it will fetch the git repositories specified in the manifest and, by doing so, setup a Yocto Project build environment for you!
1. Install Repo.
Download the Repo script:
$ curl http://commondatastorage.googleapis.com/git-repo-downloads/repo > repo
Make it executable:
$ chmod a+x repo
Move it on to your system path:
$ sudo mv repo /usr/local/bin/
If it is correctly installed, you should see a Usage message when invoked with the help flag.
$ repo --help
2. Initialize a Repo client.
Create an empty directory to hold your working files:
$ mkdir yocto
$ cd yocto
Tell Repo where to find the manifest:
$ repo init -u git://github.com/gumstix/yocto-manifest.git -b <branch>
A successful initialization will end with a message stating that Repo is initialized in your working directory. Your directory should now contain a .repo directory where repo control files such as the manifest are stored but you should not need to touch this directory.
Note: You can use the -b switch to specify the branch of the repository to use. We develop on the guaranteed-to-break warrior branch. Most people should use the morty branch, which should at least compile.
The -m switch selects the manifest file (default is default.xml). Our default.xml on morty is designed to be stable as it pins particular commits.
To test out the bleeding edge, type:
$ repo init -u git://github.com/gumstix/yocto-manifest.git -b warrior
$ repo sync
Note that the default settings for bblayers.conf and local.conf may change between branches. If the environment was originally setup with e.g. TEMPLATECONF=meta-gumstix-extras/conf, check the *.sample files in that directory for any corresponding changes needed to the settings in build/conf/.
To get back to the known stable version, type:
$ repo init -u git://github.com/gumstix/yocto-manifest.git -b morty
$ repo sync
Also you can get a specific version of Yocto Project:
For example,
$ repo init -u git://github.com/gumstix/yocto-manifest.git -b refs/tags/morty
To learn more about repo, look at Repo Command Reference
3. Fetch all the repositories:
$ repo sync
Now go turn on the coffee machine as this may take 20 minutes depending on your connection.
4. Initialize the Yocto Project Build Environment.
$ export TEMPLATECONF=meta-gumstix-extras/conf
$ source ./poky/oe-init-build-env
This copies default configuration information into the poky/build/conf
directory and sets up some environment variables for the build system. This configuration
directory is not under revision control; you may wish to edit these configuration
files for your specific setup. In particular, change the MACHINE variable in conf/local.conf if you are
not building for the Overo (default).
5. Build an image:
This process downloads several gigabytes of source code and then proceeds to do an awful lot of compilation so make sure you have plenty of space (25GB minimum), and expect a day or so of build time depending on your network connection. Don't worry---it is just the first build that takes a while.
$ bitbake gumstix-console-image
If everything goes well, you should have a compressed root filesystem tarball as well as kernel and bootloader binaries available in your tmp/deploy/images/{ overo | duovero | pepper } directory. If you run into problems, the most likely candidate is missing software packages. Check out The Build Host Packages for the list of required packages for operating system. Also, take a look to be sure your operating system is supported: Distribution Supported List
6. Create a bootable micro SD card:
You are one step closer to booting your Gumstix with the new image you built!
Usually you have to create two partitions in your uSD: boot and root, and copy the bootloader and the root file system.
Optionally you may want to create a swap partition.
You can follow the instructions given here: Create Bootable MicroSD Card
Hooray you are done!
To pick up the latest changes for all source repositories, run:
$ repo sync
Enter the Yocto Project build environment:
$ source poky/oe-init-build-env
If you forget to setup these environment variables prior to bitbaking, your
OS will complain that it can't find bitbake on the path. Don't try to
install bitbake using a package manager, just run the above command.
You can then rebuild as before:
$ bitbake gumstix-console-image
So something broke... what do you do now?
There are several degrees of starting fresh: individual packages can be rebuilt or the whole system can be reconstructed.
- clean a package: bitbake -c cleansstate
- re-download package: bitbake -c cleanall
- destroy everything but downloads: rm -rf build/sstate-cache build/tmp (or wherever your sstate and work directories are)
- destroy it all (not recommended): rm -rf build
Note: If you've made a change to a recipe and want the package to be rebuilt, just increment the recipe version (the PR variable); cleaning is not necessary.
To understand better how bitbake processes recipes, look at the excellent documentation: Yocto Project Reference Manual
To make sense of the differences between these cleaning methods, it is useful to understand that Yocto caches both the downloaded source files for all the packages it tries to build (the DL_DIR configuration parameter) and the packages once built (the SSTATE_DIR configuration parameter). Typically, deleting the downloaded source is a bad idea---this just means re-fetching gigabytes of code which wastes network bandwidth. Cleaning the sstate cache for a particular package ensures that it actually gets rebuilt from source rather than simply restored from the cache.
Sooner or later, you'll want to customize some aspect of the image either adding more packages, picking up some upstream patches, or tweaking your kernel. To this, you'll want to customize the Repo manifest to point at different repositories and branches or pull in additional meta-layers.
Clone this repository (or fork it on github):
$ git clone git://github.com/gumstix/yocto-manifest.git
Make your changes (and contribute them back if they are generally useful), and then re-initialize your repo client
$ repo init -u <file:///path/to/your/git/repository.git>
Please checkout Gumstix Yocto Project Wiki for tips on building and using the Gumstix images.