printer_BTT_SKRat.cfg

# https://github.com/Travis90x/Klipper-configuration/tree/main
# BIG TEXT ASCII http://patorjk.com/software/taag/#p=display&c=bash&f=ANSI%20Shadow&t=BED%20MESH
## ######################################



[input_shaper]
shaper_freq_x: 96 # 85.7 # 54  85.7  # edit with your results
shaper_freq_y: 57 # 54  # 85.7
shaper_type_x: ei
shaper_type_y: ei

[output_pin relay]
PIN: PA2
value: 1


[include LED.cfg]
[include START.cfg]
[include macro.cfg]
[include mainsail.cfg]
[include timelapse.cfg] # Webcam timelapse





#  
#  ███╗   ███╗ ██████╗██╗   ██╗
#  ████╗ ████║██╔════╝██║   ██║
#  ██╔████╔██║██║     ██║   ██║
#  ██║╚██╔╝██║██║     ██║   ██║
#  ██║ ╚═╝ ██║╚██████╗╚██████╔╝
#  ╚═╝     ╚═╝ ╚═════╝ ╚═════╝ 
#                         
# mcu
# ######################################
# This file contains common pin mappings for MKS Robin Nano (v1.2.004) boards. To use this config, the firmware should be compiled for the
# STM32F103. When running "make menuconfig", enable "extra low-level configuration setup", select the 28KiB bootloader, disable "USB for
# communication", and select USART3 for the "Serial Port".
# Note that the "make flash" command does not work with MKS Robin boards. After running "make", run the following command:
#   ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano.bin
# Copy the file out/Robin_nano.bin to an SD card and then restart the printer with that SD card.
# See docs/Config_Reference.md for a description of parameters.
# KLIPPER CONFIG EXAMPLE
# https://github.com/Klipper3d/klipper/blob/master/docs/Config_Reference.md


[mcu]
# serial: /dev/ttyUSB0
# serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 
serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_4000150012504B4633373520-if00

# serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_btt-skrat-10-if00
# to find correct usb, in command type: sudo ls /dev/serial/by-id/*
restart_method: command


[temperature_sensor SKRat]
sensor_type: temperature_mcu
min_temp: 0
max_temp: 100





# ######################################
#   STEPPERS
# ######################################

#  ██╗  ██╗
#  ╚██╗██╔╝
#   ╚███╔╝ 
#   ██╔██╗ 
#  ██╔╝ ██╗
#  ╚═╝  ╚═╝


[stepper_x]
step_pin: PF9
dir_pin: PD7
enable_pin: !PD6
microsteps: 64
rotation_distance: 40

# endstop_pin: tmc2209_stepper_x:virtual_endstop  # Sensorless homing
endstop_pin: ^PB5  # Orange -  add ! if physic endstop - physical/optical endstop

homing_speed: 100
homing_retract_dist: 10.0 # retract as optical probe is long from the complete collision
homing_retract_speed: 100 #
second_homing_speed: 5  # useful for optical
# homing_retract_dist: 0  # sensorless homing = 0

# 310x310 BED 0,0 is your 0,0
# Measure Screw 4 (coordinate 35,35) if nozzle on X is over
# increase position endstop. If under, decrease
################
position_endstop: 304
################

position_min: 4  # position_endstop - how many mm you can "press" the endstop
position_max: 305

# Toolhead phisical limit with Diamond and Optical Endstop
# position_endstop: -1

# position_min: -1
# position_max: 300


[tmc2240 stepper_x]
cs_pin: PF10
diag1_pin: PB5
spi_software_mosi_pin: PC12
spi_software_miso_pin: PC11
spi_software_sclk_pin: PC10

# uart_pin: PA10
# uart_address: 3
# tx_pin: 
# sense_resistor: 0.110

interpolate: True # Reduce Noise. For best positional accuracy consider using spreadCycle mode and disable interpolation
run_current: 1

stealthchop_threshold: 0 # Max 999999
# The velocity (in mm/s) to set the "stealthChop" threshold to. 
# When set, "stealthChop" mode will be enabled if the stepper motor
# velocity is below this value. The default is 0, which disables "stealthChop" mode.

# diag_pin: ^PA15  # sensorless homing
# hold_current: 0.80  # Disable for sensorless Homing - The current for motor in idle: it's not recommended use it.
# If defined, TMC driver can reduce current to the stepper motor when it detects that the stepper is not moving.
# The switch from run_current to hold_current has a negative impact on precision.

# driver_SGTHRS: 100 # Sensorless homing, 0-255, high has more sensibility
# endstop_pin: tmc2209_stepper_x:virtual_endstop

#[temperature_sensor stepper_x]
#sensor_type: temperature_driver
#sensor_driver: tmc2240 stepper_x

#  ██╗   ██╗
#  ╚██╗ ██╔╝
#   ╚████╔╝ 
#    ╚██╔╝  
#     ██║   
#     ╚═╝   
  

[stepper_y]
step_pin: PD3
dir_pin: PD2
enable_pin: !PD5
microsteps: 64
rotation_distance: 40
# endstop_pin: tmc2209_stepper_y:virtual_endstop  # Sensorless homing
endstop_pin: ^PC1 # Blue  - add ! if physic endstop, remove if optical - physical/optical endstop

homing_speed: 100
homing_retract_dist: 10.0 # retract as optical probe is long from the complete collision
homing_retract_speed: 100 #
second_homing_speed: 5  # useful for optical

# 310x310 BED 0,0 is your 0,0
# Measure Screw 4 (coordinate 35,35) if nozzle on Y is over the screw
# increase position endstop. If under the screw, decrease.
################
position_endstop: -6
################

position_min: -12  # optical
position_max: 297 # position_endstop + how many mm you can "press" the endstop


[tmc2240 stepper_y]
cs_pin: PD4
spi_software_mosi_pin: PC12
spi_software_miso_pin: PC11
spi_software_sclk_pin: PC10
diag1_pin: PC1

# uart_pin: PA10
# uart_address: 2
# sense_resistor: 0.110

interpolate: True
run_current: 1

stealthchop_threshold: 0 # Max 999999
# diag_pin: ^PA12  # sensorless homing
# driver_SGTHRS: 100 # Sensorless homing, 0-255, high has more sensibility



#  ███████╗
#  ╚══███╔╝
#    ███╔╝ 
#   ███╔╝  
#  ███████╗
#  ╚══════╝


[stepper_z]
step_pin: PA15
dir_pin: !PF8
enable_pin: !PC9
microsteps: 16
rotation_distance: 8
# endstop_pin = probe:z_virtual_endstop   # for Endstop Z with BL Touch
endstop_pin: ^PC0   # 1st Green on Robin Nano 1.2 - disable with BLtouch as endstop -  endstop pin PB3 without >!<
#############################################################################################################
# disable with bltouch as endstop
#position_endstop: 315

# increase for nozzle far from bed at Z0
#(nozzle touch bed in negative value)

position_min: -2.5  # your 0-position_endstop
position_max: 316  # 330 with oldham and stepper lowered with thicknesses
# 320 with Pom anti backlash, oldham and stepper lowered with thicknesses
homing_speed: 50
homing_retract_dist: 10.0 # retract as optical/physic probe is long
homing_retract_speed: 10 # 
second_homing_speed: 2  # increase precision


[tmc2209 stepper_z]
uart_pin: PC8
# uart_address: 1
diag_pin: PC0
interpolate: True
run_current: 0.9
sense_resistor: 0.110
stealthchop_threshold: 0 
# don't use 0.1 = stealthchop enabled only when the bed is static
# avoid to switch spreadcycle to stealthchop and viceversa during printing


#  ███████╗ ██╗
#  ╚══███╔╝███║
#    ███╔╝ ╚██║
#   ███╔╝   ██║
#  ███████╗ ██║
#  ╚══════╝ ╚═╝


[stepper_z1]
step_pin: PC7
dir_pin: !PC6
enable_pin: !PD9
microsteps: 16
rotation_distance: 8
endstop_pin: ^PF4 # 2nd Green
# endstop_pin: PA11 # as Z0

# not supported on Z1:
# position_endstop: 
# position_min: -1.5 # not supported on Z1
# position_max: 330 # not supported on Z1
# homing_speed: 15
# second_homing_speed:5


[tmc2209 stepper_z1]
uart_pin: PD8
# uart_address: 0
diag_pin: PF4
interpolate: True
run_current: 0.9
sense_resistor: 0.110
stealthchop_threshold: 0

############################################################
#    
#  ███████╗██╗  ██╗████████╗██████╗ ██╗   ██╗██████╗ ███████╗██████╗ 
#  ██╔════╝╚██╗██╔╝╚══██╔══╝██╔══██╗██║   ██║██╔══██╗██╔════╝██╔══██╗
#  █████╗   ╚███╔╝    ██║   ██████╔╝██║   ██║██║  ██║█████╗  ██████╔╝
#  ██╔══╝   ██╔██╗    ██║   ██╔══██╗██║   ██║██║  ██║██╔══╝  ██╔══██╗
#  ███████╗██╔╝ ██╗   ██║   ██║  ██║╚██████╔╝██████╔╝███████╗██║  ██║
#  ╚══════╝╚═╝  ╚═╝   ╚═╝   ╚═╝  ╚═╝ ╚═════╝ ╚═════╝ ╚══════╝╚═╝  ╚═╝
#    
# EXTRUDER
############################################################

[extruder]
# invert direction  !PB4 Nema17

step_pin: PB10
dir_pin: !PE15
enable_pin: !PA8
microsteps: 16


# ROTATION DISTANCE = full steps per rotation (200) * microsteps / steps per mm / Gear ratio
# rotation_distance: 22.65 # diminuisci se sottoestrude - 
# 23.3 = Sherpa Mini + Moon 14 8th
# rotation_distance: 22  # diminuisci se sottoestrude 20 25  -- 22.5 = 10cm microsteps: 32 microstep 32 -> 23 # microstep 64 -> 45
rotation_distance: 22.6 # Vz-Hextrudort-Low # 23.23 default
# rotation_distance: 22.65 # Libra mini


full_steps_per_rotation: 200  # 200 for 1.8 degree Motor  - 400 for 0.9 deg # Default 200
gear_ratio: 50:8 # 50:17 for BMG clone extruder otherwise 3:1 
# 50:8 Moon 8t # 50:10 Moon 10 tooths
# 50:8 8th and Sherpa Mini, Libra Mini, Vz-Hextrudort
nozzle_diameter: 0.400

filament_diameter: 1.750
#
max_extrude_only_distance: 1400.0
max_extrude_only_accel: 1700 #  mm/s^2
max_extrude_only_velocity: 100.0  # G1 EX mm/s
# Maximum velocity (in mm/s) and acceleration (in mm/s^2) of the extruder motor for retractions and extrude-only moves
# max_extrude_only_velocity:  75 # SHERPA MINI 
# max_extrude_only_accel: 1500  # SHERPA MINI 
# https://github.com/Annex-Engineering/Sherpa_Mini-Extruder/blob/master/Klipper_Config_Block.txt
max_extrude_cross_section: 100.0 # The default is: 4x nozzle_diameter^2



heater_pin: PD12 # Default PC3

### Heater Sensor  MAX31865 ###
sensor_type: MAX31865
sensor_pin: PA4 # CS SPI1_NSS MAX31865
spi_bus: spi1  # SCK PA5 - MISO PA6 - MOSI PA7
# spi_software_sclk_pin: PA5
# spi_software_miso_pin: PA6
# spi_software_mosi_pin: PA7
# rtd_use_50Hz_filter: True
#rtd_nominal_r: 1000
#rtd_reference_r: 4300
#rtd_num_of_wires: 2
# min_temp: -273.15
# max_temp: 9999999999
# spi_speed: 100000


# sensor_pin: PC1  # Black TH2 PC1  - Violet TH1 PC2
# sensor_type: PT1000
# pullup_resistor: 4700
# sensor_type: DYZE
# sensor_type: EPCOS 100K B57560G104F
# sensor_type: ATC Semitec 104GT-2 #stock
# sensor_type: ATC Semitec 104NT-4-R025H42G
# sensor_type: Generic 3950
# sensor_type: Honeywell 100K 135-104LAG-J01
# sensor_type: NTC 100K MGB18-104F39050L32
# sensor_type: SliceEngineering 450
# sensor_type: TDK NTCG104LH104JT1

# pullup_resistor: 4700
min_temp: 0.15 # min is -273.15  # debug
max_temp: 310 # 350 #
min_extrude_temp: 10.15  # 140 # min 5.15 # debug

####################
# PID EXTRUDER
####################

pwm_cycle_time: 0.02 # default pwm_cycle_time: 0.1 (10Hz,the max for SSR)
max_power: 1.0
smooth_time: 0.5  # default 1.0


# NF CRAZY VOL CO HF 70W 2x 4020 100%
# smooth 0.1 cycle_time: 0.02
#control: pid
#pid_kp: 44.661
#pid_ki: 5.838
#pid_kd: 85.415

# NF CRAZY VOL CO HF 70W 2x 4020 100%
# smooth 1.0 cycle_time: 0.1
# control: pid
# pid_kp: 18
# pid_ki: 1.3
# pid_kd: 62

# 10Hz NF CRAZY VOL CO HF 70W 2x 4020 100%
# control: pid
# pid_kp: 26.948
# pid_ki: 7.811
# pid_kd: 23.243

# NF CRAZY VOL CO HF 70W 2x 4020 50%  pid_Kp=23.744 pid_Ki=11.307 pid_Kd=12.466


# NF CRAZY VOL CO HF 50W 2x 4020 100%
# pid_kp = 46.506
# pid_ki = 103.346
# pid_kd = 5.232

# control = pid
# PID EPCOS 100K B57560G104F
# pid_Kp: 30.425
# pid_Ki: 2.359
# pid_Kd: 98.120

#########################
pressure_advance: 0.05
# PLA 0.045 100mm/s
# PLA 0.08 40mm/s
# PETG
#########################



[tmc2209 extruder]
uart_pin: PB11   # NB extruder on 3rd Position to use same Fan of XY
# uart_address: 0
interpolate: False
run_current: 0.9 # 0.9 for stock motor nema 17 - 0.35 nema 14 sth17 or fysetc clone- 0.85 nema 14 STH20 or moons CSE14HRA1L410A-02
#run_current: 0.35 #per motore nema 14 STH17 o clone fysetc
#run_current: 0.85 #per motore nema 14 STH20 o moons
# hold_current: 0.85 #  Disable for sensroless Homing -  0.85 for nema 14 STH20 or moons motor #0.35 for nema 14 STH17 or fysetc clone motor
sense_resistor: 0.110
stealthchop_threshold: 0

#######################################
#   
#  ██████╗ ██╗  ████████╗ ██████╗ ██╗   ██╗ ██████╗██╗  ██╗
#  ██╔══██╗██║  ╚══██╔══╝██╔═══██╗██║   ██║██╔════╝██║  ██║
#  ██████╔╝██║     ██║   ██║   ██║██║   ██║██║     ███████║
#  ██╔══██╗██║     ██║   ██║   ██║██║   ██║██║     ██╔══██║
#  ██████╔╝███████╗██║   ╚██████╔╝╚██████╔╝╚██████╗██║  ██║
#  ╚═════╝ ╚══════╝╚═╝    ╚═════╝  ╚═════╝  ╚═════╝╚═╝  ╚═╝
#   
#   BLTOUCH
#######################################

# SCREWS
# 1-----2
# |  X  |
# 4-----3

[bltouch]
sensor_pin: ^PE5  # prefix or remove  !  to reverse the logic TRIGGERED/OPEN
# Mt_Det2 pin Robin Nano 1.2 - prefix with ^ to pullup if you haven't a pullup resistor on signal
control_pin: PE6 # PA8 -> PB2 ALERT: check correct pin for your Robin Nano
# PA8 stock servo 3pin
# use PB2 as secondary Servo Pin
# set_output_mode: 5V
pin_move_time: 0.680
stow_on_each_sample: True # BL gp UP every point
# probe_with_touch_mode: True # True if BL Touch > v3  - true with filtered capacitor on pin
# pin_up_reports_not_triggered: False    # On clone with query issue
# pin_up_touch_mode_reports_triggered: False   #On clone with query issue

#######################################
x_offset: 0 

y_offset: 38 

z_offset: 3   # >0.0 - increase if Z bed mesh is positive  
# PROBE on the center position
# If negative, move the endstops position

speed: 5
samples: 3
###################
sample_retract_dist: 6.0 # the distance (in mm) to lift the toolhead between each sample 
###################
samples_result: average
samples_tolerance: 0.050
samples_tolerance_retries: 0
lift_speed: 20

# [safe_z_home]
# z_hop: 3           #  Move up
# z_hop_speed: 10
# home_xy_position: 0, 275 #  stepper_y{position_max} # Change coordinates to the center of your print bed
# speed: 100


#  ███╗   ███╗███████╗███████╗██╗  ██╗
#  ████╗ ████║██╔════╝██╔════╝██║  ██║
#  ██╔████╔██║█████╗  ███████╗███████║
#  ██║╚██╔╝██║██╔══╝  ╚════██║██╔══██║
#  ██║ ╚═╝ ██║███████╗███████║██║  ██║
#  ╚═╝     ╚═╝╚══════╝╚══════╝╚═╝  ╚═╝
#     

# SCREWS
# 1-----2
# |  X  |
# 4-----3

[bed_mesh]
probe_count: 9,9
speed: 200

mesh_min: 15, 30

# X_mesh_min = X coordinate + BL-Touch x_offset
# the result must be > Xmin position
# Y_mesh_min = Y coordinate + BL-Touch y_offset
# the result must be > Ymin position


mesh_max: 295, 280  # 275, 275 if the BED 0,0 is your 0,0
# X= X_Bed - X_mesh_min  (Ex: X bed 310, X_mesh_min=5  X_mesh_max= 305 )
# Y= Y_Bed -  Y_mesh_min (Ex: Y bed 310, Y_mesh_min=35  X_mesh_max= 275 )
# Y< Ymax Printer limit - Y BLtouch offset

###################
horizontal_move_z: 6  # >z_offset probe The Z coordinate the probe rises to prior to traveling between points.
###################

fade_start: 1.0
fade_end: 10.0
split_delta_z: .025
move_check_distance: 5.0
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: .2




[z_tilt]
z_positions:
    -15,150
    325,150
points:
    35,109  # 35, 150-(BL-Touch Y Offset)
    275,109
#     35,311     35,71     275,71     275,311
speed: 150
horizontal_move_z: 10
retries: 1
retry_tolerance: 0.01 # >0


#######################################
#  ██████╗ ███████╗██████╗ 
#  ██╔══██╗██╔════╝██╔══██╗
#  ██████╔╝█████╗  ██║  ██║
#  ██╔══██╗██╔══╝  ██║  ██║
#  ██████╔╝███████╗██████╔╝
#  ╚═════╝ ╚══════╝╚═════╝ 
#   BED
#######################################

[heater_bed]
heater_pin: PD13  # Default PA0
pullup_resistor: 4700  # default 4700
smooth_time: 1.0  # default 1.0
max_power: 1.0  #default 1.0
pwm_cycle_time: 0.1  #default 0.1 (10Hz, tha max for SSR relay)
sensor_type: EPCOS 100K B57560G104F
# sensor_type: NTC 100K beta 3950
sensor_pin: PB2 # lateral


min_temp: -273.15   #  min -273.15
max_temp: 150 # 130
# control: watermark
#control: pid
# Stock BED
# pid_Kp: 325.10
# pid_Ki: 63.35
# pid_Kd: 417.10

# AC BED
#pid_Kp: 48.731
#pid_Ki: 1.683
#pid_Kd: 352.688


#######################################
# 
#  ████████╗███████╗███╗   ███╗██████╗ 
#  ╚══██╔══╝██╔════╝████╗ ████║██╔══██╗
#     ██║   █████╗  ██╔████╔██║██████╔╝
#     ██║   ██╔══╝  ██║╚██╔╝██║██╔═══╝ 
#     ██║   ███████╗██║ ╚═╝ ██║██║     
#     ╚═╝   ╚══════╝╚═╝     ╚═╝╚═╝ 
#   TEMPERATURES
#######################################



#######################################
# 
#  ███████╗ █████╗ ███╗   ██╗
#  ██╔════╝██╔══██╗████╗  ██║
#  █████╗  ███████║██╔██╗ ██║
#  ██╔══╝  ██╔══██║██║╚██╗██║
#  ██║     ██║  ██║██║ ╚████║
#  ╚═╝     ╚═╝  ╚═╝╚═╝  ╚═══╝
#
#   FANS
#######################################


#FAN 3030 on Hotend
[heater_fan extruder]
heater: extruder
pin: PE11  # Default PB1
kick_start_time: 0.4
max_power: 1
off_below: 0.0
shutdown_speed: 1.0
cycle_time: 0.010
heater_temp: 65.0
fan_speed: 1
#tachometer_pin:
#tachometer_ppr: 2
#tachometer_poll_interval: 0.0015
#hardware_pwm: False
#enable_pin:



# 2x fan 4020 on FANDUCT
[fan]
pin: PE13
kick_start_time: 0.5
max_power: 1.0
off_below: 0


# [multi_pin dual_fan_extruder]
# pins:PB1,PB2


[board_pins fan_tmc]
aliases:
    fan_tmc_pin=PD15
    

[controller_fan driver_fan]
# Turn ON fan when a stepper/heater is ON

# if not declared, default is
# stepper: stepper_x, stepper_y, stepper_z, stepper_z1, ecc... , extruder
# heater: extruder

#   Name of the config section defining the heater/stepper that this fan
#   is associated with. If a comma separated list of heater/stepper names
#   is provided here, then the fan will be enabled when any of the given
#   heaters/steppers are enabled. The default heater is "extruder", the
#   default stepper is all of them.


pin: fan_tmc_pin # pwm fan pin
max_power: 1
shutdown_speed: 1.0 # in soft pwm is allowed 1 or 0
kick_start_time: 0.1
off_below: 0.40
idle_speed: 0.7 # Fan speed when stepper/heater are off
idle_timeout: 1 # Turn off fan after x secondos from stepper/heater is off

# to exclude activation fan with extruder
# I find a workaround creating a fake sensor and heater on an free pin, so:
# [duplicate_pin_override] # needed to use only 1 not connected PIN for FAKE_HEATER
# pins: PC2

# [heater_generic fake_heater]
# sensor_type: PT1000 # Put here whatever sensor you want
# heater_pin: PC2 # use a not connected PIN
# sensor_pin: PC2 # use a not connected PIN
# gcode_id: 1
# min_temp: -273.15   #  min -273.15
# max_temp: 9999
# control: watermark
# max_delta: 9999

# SENSOR TYPE not provided from Klipper
# you have to define 3 value of resistance/temperature, measure your temperature probe with a tester 
# [thermistor DYZE]
# https://www.aliexpress.com/item/4000591370691.html
# https://docs.dyzedesign.com/hotends.html#klipper-firmware
# dyze500 clone
# temperature1: 60
# resistance1: 666000 #450000
# temperature2: 162
# resistance2: 22200
# temperature3: 280
# resistance3: 1555




#######################################
# 
#  ██████╗ ██████╗ ██╗███╗   ██╗████████╗███████╗██████╗ 
#  ██╔══██╗██╔══██╗██║████╗  ██║╚══██╔══╝██╔════╝██╔══██╗
#  ██████╔╝██████╔╝██║██╔██╗ ██║   ██║   █████╗  ██████╔╝
#  ██╔═══╝ ██╔══██╗██║██║╚██╗██║   ██║   ██╔══╝  ██╔══██╗
#  ██║     ██║  ██║██║██║ ╚████║   ██║   ███████╗██║  ██║
#  ╚═╝     ╚═╝  ╚═╝╚═╝╚═╝  ╚═══╝   ╚═╝   ╚══════╝╚═╝  ╚═╝
# 
#   PRINTER
#######################################


[gcode_macro _CLIENT_VARIABLE]
variable_use_custom_pos   : True  ; use custom park coordinates for x,y [True/False]
variable_custom_park_x    : 150.0  ; custom x position; value must be within your defined min and max of X
variable_custom_park_y    : -10.0  ; custom y position; value must be within your defined min and max of Y
variable_custom_park_dz   : 2.0   ; custom dz value; the value in mm to lift the nozzle when move to park position
variable_retract          : 2.0   ; the value to retract while PAUSE
variable_cancel_retract   : 5.0   ; the value to retract while CANCEL_PRINT
variable_speed_retract    : 25.0  ; retract speed in mm/s
variable_unretract        : 2.0   ; the value to unretract while RESUME
variable_speed_unretract  : 25.0  ; unretract speed in mm/s
variable_speed_hop        : 15.0  ; z move speed in mm/s
variable_speed_move       : 150.0 ; move speed in mm/s
variable_park_at_cancel   : True  ; allow to move the toolhead to park while execute CANCEL_PRINT [True/False]
variable_park_at_cancel_x : 150.0 ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
variable_park_at_cancel_y : -10.0 ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
# !!! Caution [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True !!!
variable_use_fw_retract  : False ; use fw_retraction instead of the manual version [True/False]
gcode:


[exclude_object]

[firmware_retraction]
retract_length: 0.5   # default 0 mm
#   The length of filament (in mm) to retract when G10 is activated, and to unretract when G11 is activated (but see unretract_extra_length below). 
retract_speed: 35    # default is 20 mm/s
#   The speed of retraction, in mm/s.
#unretract_extra_length: 0
#   The length (in mm) of *additional* filament to add when unretracting.
unretract_speed: 35  # default is 10 mm/s.
#   The speed of unretraction, in mm/s. The default is 10 mm/s.




# SCREWS
# 1-----2
# |  X  |
# 4-----3

# 310x310 BED 0,0 is your 0,0
[bed_screws]
screw1: 35, 275
screw2: 275, 275
screw3: 275, 35
screw4: 35, 35

# if your 0,0 is the BED phisical limit of your printer with Diamond and enstop optical
# [bed_screws] 
# screw1: 26, 265
# screw2: 266, 265
# screw3: 266, 25
# screw4: 26, 25



### to enalbe M117
[display_status]

### to enable M118
[respond]
#default_type: echo
#   Sets the default prefix of the "M118" and "RESPOND" output to one
#   of the following:
#       echo: "echo: " (This is the default)
#       command: "// "
#       error: "!! "
default_prefix:
#   Directly sets the default prefix. If present, this value will
#   override the "default_type".

[pause_resume]

[gcode_arcs]
resolution: 0.5

[printer]
kinematics: corexy
#♥ kinematics: limited_corexy
# https://github.com/Piezoid/klipper/blob/work-peraxis/klippy/kinematics/limited_corexy.py
max_velocity: 300
# max_x_velocity: 250 # only on limited_cartesian.py
# max_y_velocity: 20
max_accel: 8000
max_accel_to_decel: 4000
# max_x_accel: 8000 # limited_corexy
# max_y_accel: 6000 # limited_corexy
max_z_velocity: 50
max_z_accel: 70
square_corner_velocity: 5

[force_move]
enable_force_move: True

[save_variables]
filename: /home/pi/printer_data/config/save_variables.cfg  # needed for Power Loss Recovery plr.cfg
# filename: ~/variable.cfg  # needed for Power Loss Recovery plr.cfg
# filename: /home/pi/printer_data/config/printer_variables.cfg
# filename: /home/pi/klipper_config/.variables.stb


# ATTENTION: if parameters in SAVE CONFIG was't found by Klipper, check in the code before '#*#' and delete

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [stepper_z]
#*# position_endstop = 314.715
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	0.380000, 0.420833, 0.448333, 0.493333, 0.510833, 0.504167, 0.470833, 0.413333, 0.400833
#*# 	0.370000, 0.402500, 0.444167, 0.485000, 0.443333, 0.456667, 0.455000, 0.377500, 0.363333
#*# 	0.307500, 0.362500, 0.383333, 0.384167, 0.369167, 0.422500, 0.394167, 0.368333, 0.334167
#*# 	0.331667, 0.378333, 0.424167, 0.413333, 0.395833, 0.376667, 0.342500, 0.323333, 0.287500
#*# 	0.347500, 0.425000, 0.435000, 0.433333, 0.453333, 0.429167, 0.404167, 0.345833, 0.315833
#*# 	0.345833, 0.420833, 0.426667, 0.492500, 0.463333, 0.423333, 0.404167, 0.355833, 0.333333
#*# 	0.410833, 0.414167, 0.441667, 0.515833, 0.527500, 0.492500, 0.421667, 0.419167, 0.347500
#*# 	0.429167, 0.457500, 0.495000, 0.548333, 0.535000, 0.536667, 0.487500, 0.439167, 0.491667
#*# 	0.390833, 0.432500, 0.520833, 0.538333, 0.484167, 0.519167, 0.465000, 0.436667, 0.428333
#*# x_count = 9
#*# y_count = 9
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 15.0
#*# max_x = 295.0
#*# min_y = 30.0
#*# max_y = 280.0
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 24.513
#*# pid_ki = 1.527
#*# pid_kd = 98.360
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 58.197
#*# pid_ki = 2.752
#*# pid_kd = 307.718