Skip to content

Latest commit

 

History

History
169 lines (129 loc) · 7.09 KB

INSTALL.rst

File metadata and controls

169 lines (129 loc) · 7.09 KB

Installation

1. INTRODUCTION

Ignore the installation instructions in this file if you have a pre-installed binary package. When upgrading from older versions of FreeRADIUS, you should read ALL of this file, especially the section on "UPGRADING" below which gives information on how to update your configuration.

Whether you are installing from source or a pre-built binary package, you should read the section below "RUNNING THE SERVER".

2. SIMPLE INSTALLATION

If you do not need to modify the default configuration, then take the following steps to build and install the server:

$ ./configure
$ make
$ make install

3. CUSTOM INSTALLATION

FreeRADIUS has autoconf support. This means you have to run ./configure, and then run make. To see which configuration options are supported, run ./configure --help, and read it's output. The following list is a selection from the available flags:

--enable-shared[=PKGS]  build shared libraries [default=yes]
--enable-static[=PKGS]  build static libraries [default=yes]
--with-logdir=DIR       Directory for logfiles [LOCALSTATEDIR/log]
--with-radacctdir=PATH  Directory for detail files [LOGDIR/radacct]
--with-raddbdir=DIR     Directory for config files [SYSCONFDIR/raddb]
--with-threads          Use threads, if available.  (default=yes)
--with-snmp             Compile in SNMP support. (default=yes)
--with-dhcp             Compile in DHCP support. (default=yes)
--with-experimental-modules  Use experimental and unstable modules.
                             (default=no)
--enable-developer      Turns on super-duper-extra-compile-warnings
                        when using gcc, as well as experimental modules.

The make install stage will install the binaries, the 'man' pages, and MAY install the configuration files. If you have not installed a RADIUS server before, then the configuration files for FreeRADIUS will be installed. If you already have a RADIUS server installed, then

FreeRADIUS WILL NOT over-write your current configuration.

The make install process will warn you about the files it could not install.

If you see a warning message about files that could not be installed, then you MUST ensure that the new server is using the new configuration files, and not the old configuration files. The initial output from running in debugging mode (radiusd -X) will tell you which configuration files are being used. See UPGRADING above for information about upgrading from older versions. There MAY be changes in the dictionary files which are REQUIRED for a new version of the software. These files will NOT be installed over your current configuration, so you MUST verify and install any problem files by hand, for example using diff(1) to check for changes.

It is EXTREMELY helpful to read the output of both ./configure, make, and make install. If a particular module you expected to be installed was not installed, then the output of the ./configure; make; make install sequence will tell you why that module was not installed. Please do NOT post questions to the FreeRADIUS users list without first carefully reading the output of this process.

4. UPGRADING

The installation process will not over-write your existing configuration files. It will, however, warn you about the files it did not install.

For users upgrading from any older version to 3.0, it is NOT possible to use the older configuration as-is. However, the version 2.x configuration is largely compatible, so upgrading the configuration should not be too difficult. For details on what has changed, see raddb/README.rst.

We STRONGLY recommend that 3.0 be installed in a different location than any existing 1.x or 2.x installation. Any local policies can then be migrated gradually to the new 3.0 configuration. The number of differences in the new configuration mean that is is both simpler and safer to migrate your configurations rather than to try and just get the old configuration to work.

5. RUNNING THE SERVER

If the server builds and installs, but doesn't run correctly, then you should use debugging mode (radiusd -X) to figure out the problem.

This is your BEST HOPE for understanding the problem. Read ALL of the messages which are printed to the screen, the answer to your problem will often be in a warning or error message.

We really can't emphasize that last sentence enough. Configuring a RADIUS server for complex local authentication isn't a trivial task. Your ONLY method for debugging it is to read the debug messages, where the server will tell you exactly what it's doing, and why. You should then compare its behaviour to what you intended, and edit the configuration files as appropriate.

If you don't use debugging mode, and ask questions on the mailing list, then the responses will all tell you to use debugging mode. The server prints out a lot of information in this mode, including suggestions for fixes to common problems. Look especially for "WARNING" in the output, and read the related messages.

Since the main developers of FreeRADIUS use debugging mode to track down their configuration problems with the server, it's a good idea for you to use it, too. If you don't, there is little hope for you to solve ANY configuration problem related to the server.

To start the server in debugging mode, do:

$ radiusd -X

You should see a lot of text printed on the screen as it starts up. If you don't, or if you see error messages, please read the FAQ:

http://www.freeradius.org/faq/

If the server says "Ready to process requests.", then it is running properly. From another shell (or another window), type:

$ radtest test test localhost 0 testing123

You should see the server print out more messages as it receives the request, and responds to it. The 'radtest' program should receive the response within a few seconds. It doesn't matter if the authentication request is accepted or rejected, what matters is that the server received the request, and responded to it.

You can now edit the configuration files for your local system. You will usually want to start with sites-enabled/default. To set which NASes (clients) can communicate with this server, edit clients.conf. Please read the configuration files carefully, as many configuration options are only documented in comments in the file.

Note that is is HIGHLY recommended that you use some sort of version control system to manage your configuration, such as git or Subversion. You should then make small changes to the configuration, checking in and testing as you go. When a config change causes the server to stop working, you will be able to easily step back and find out what update broke the configuraiton.

Configuring and running the server MAY be complicated. Many modules have man pages. See man rlm_pap, or man rlm_* for information. Please read the documentation in the doc/ directory. The comments in the configuration files also contain a lot of documentation.

If you have any additional issues, the FAQ is also a good place to start.