-
Notifications
You must be signed in to change notification settings - Fork 18
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
889LM flashing red and yellow on ratgdo command #68
Comments
Yes 889LM should work (mine does). ratgdo should hear the serial data and stop emulation mode (which you can see happening in your log). What I can't tell is what's causing the 889LM to drop off and restart it's sync. I see you sent a number of mqtt commands, how long did you wait between each one? |
i wasnt sure how to add a good timestamp in the logs, so near the end where there is a lot of looped output, i waited for a full cycle:
the time between 6 and 7 was at least 5 minutes. the wall panel reset 2 or 3 times before it finally went solid yellow. I can get another log tonight. let me know if you want me to try any other steps or a different sequence. In my testing yesterday this was always constant:
|
wanted to add that this is a post-recall 889LM (manufactured Sep 2023) |
Just moved to the esphome secplus 1 to see if that would help and i still have the same behavior here. The logging through the esphome build doesnt seem to be quite as detailed as what i was pulling of the serial console. Status is all reported fine, obstruction, open/close, light, but if i issue a command the wall panel reboots a few times. |
log output from esphome
wall panel was rebooting for about two minutes before the log output started again |
I spent some time trying to grab some logs to help troubleshoot this as I believe I'm having the same issue. Sequence of events:The door takes approx 13 seconds to open and also to close Power cycled ratgdo (changed from wall power to laptop)....MQTT Open 1: esp-web-tools-logs - MQTT Open 1.txt
MQTT Close 1: esp-web-tools-logs - MQTT Close 1.txt
MQTT Open 2: esp-web-tools-logs - MQTT Open 2.txt
MQTT Close 2: esp-web-tools-logs - MQTT Close 2.txt
Power Cycle Garage Door (ratgdo remained on): esp-web-tools-logs - GDO Power Cycle.txt
MQTT Open 3: esp-web-tools-logs - MQTT Open 3.txt
MQTT Close 3: esp-web-tools-logs - MQTT Close 3.txt
Power Cycle ratgdo: esp-web-tools-logs - ratgdo Power Cycle.txtMQTT Open 4: esp-web-tools-logs - MQTT Open 4.txt
MQTT Close 4: esp-web-tools-logs - MQTT Close 4.txt
Panel Open: esp-web-tools-logs - Panel Open.txt
Panel Close: esp-web-tools-logs - Panel Close.txt
MQTT Open 5: esp-web-tools-logs - MQTT Open 5.txt
MQTT Closed 5: esp-web-tools-logs - MQTT Close 5.txt
Note: It would be very helpful if a timestamp or some other counter could be added to the logs |
I can second this. A couple of days ago, I switched out my old wall panel for an 889LM. After charging, it worked for a bit, then started randomly opening and closing, with the incompatible lights flashing. Finally, it stopped midway, at which point I disconnected the power and reconnected my old panel. Unfortunately, since I only had a little bit of time, I couldnt get any logs (also my ratgdo wont reconnect after a reboot without me toggling between channels 6 and 11 on my 2.4ghz network.) Following this issue therefore. thanks! |
still having this issue on 2024.7.0 esphome and a build date of today. Im hoping maybe this PR will help ratgdo/esphome-ratgdo#304
|
Hi, I have 4 ratgdo installed, 1 is security 2.0 and 3 are security+. Everything is working on emulation mode, but I just moved one of the security+ wall panels from a doorbell to an 889LM to test it out (emulation mode worked for all doors)
When i hooked up the 889LM it flashes quickly red+yellow (manual indicates this is charging it battery) then the light goes solid yellow. During this time the ratgdo correctly shows all status updates in home assistant/mqtt. Wall panel works, wireless remote works. When I issue commands over mqtt, the wall panel flashes slowly red+yellow (manual indicates this wall panel isnt compatible with my opener). After a few reboots of the wall panel, it eventually goes solid yellow and everything works again.
edit* i also reflashed with 2.57 and erased everything just to be sure it was setup correct.
I can go back to emulation mode, but I expected this to work? Logs are attached.
garage-south-889LM-log.txt
The text was updated successfully, but these errors were encountered: