FB logo bootscreen

Marlin/Configuration.h

@@ -37,6 +37,12 @@
  */
 #define CONFIGURATION_H_VERSION 02010200
 
+
+#define DIAG_JUMPERS_REMOVED
+//#define MOTHERBOARD BOARD_LINUX_RAMPS
+
+
+
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
@@ -60,8 +66,8 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
-//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
+#define STRING_CONFIG_H_AUTHOR "adequator" // Who made the changes.
+#define CUSTOM_VERSION_FILE version.h // Path from the root directory (no quotes)
 
 /**
  * *** VENDORS PLEASE READ ***
@@ -98,7 +104,12 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT -1
+#define SERIAL_PORT 0
+
+#if MOTHERBOARD == BOARD_MKS_ROBIN_NANO_V3
+  #define SERIAL_PORT -1
+#endif
+
 
 /**
  * Serial Port Baud Rate
@@ -1773,7 +1784,11 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-#define FILAMENT_RUNOUT_SENSOR
+
+#if MOTHERBOARD == BOARD_MKS_ROBIN_NANO_V3
+  #define FILAMENT_RUNOUT_SENSOR
+#endif
+
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
@@ -3012,7 +3027,7 @@
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extui'.
 //
-#define EXTENSIBLE_UI
+//#define EXTENSIBLE_UI
 
 #if ENABLED(EXTENSIBLE_UI)
   //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
@@ -3109,17 +3124,21 @@
 //#define TFT_GENERIC
 #if ENABLED(TFT_GENERIC)
   // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
-  #define TFT_DRIVER AUTO
+  #define TFT_DRIVER ST7796
 
   // Interface. Enable one of the following options:
   //#define TFT_INTERFACE_FSMC
-  //#define TFT_INTERFACE_SPI
+  #define TFT_INTERFACE_SPI
 
   // TFT Resolution. Enable one of the following options:
   //#define TFT_RES_320x240
   //#define TFT_RES_480x272
   //#define TFT_RES_480x320
+  #define TFT_RES_320x480
   //#define TFT_RES_1024x600
+
+  #define TFT_DEFAULT_ORIENTATION  TFT_INVERT_Y
+
 #endif
 
 /**
@@ -3133,13 +3152,16 @@
  *   root of your SD card, together with the compiled firmware.
  */
 //#define TFT_CLASSIC_UI
-//#define TFT_COLOR_UI
-#define TFT_LVGL_UI
+#define TFT_COLOR_UI
+//#define TFT_LVGL_UI
 
 #if ENABLED(TFT_LVGL_UI)
-  #define MKS_WIFI_MODULE  // MKS WiFi module
+  //#define MKS_WIFI_MODULE  // MKS WiFi module
 #endif
 
+
+#define COLOR_BACKGROUND COLOR_BLACK
+
 /**
  * TFT Rotation. Set to one of the following values:
  *
@@ -3148,7 +3170,7 @@
  *   TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  *   TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  */
-#define TFT_ROTATION TFT_ROTATE_270
+//#define TFT_ROTATION TFT_ROTATE_270
 
 //=============================================================================
 //============================  Other Controllers  ============================
@@ -3174,7 +3196,7 @@
   //#define DISABLE_ENCODER         // Disable the click encoder, if any
   //#define TOUCH_IDLE_SLEEP_MINS 5 // (minutes) Display Sleep after a period of inactivity. Set with M255 S.
 
-  #define TOUCH_SCREEN_CALIBRATION
+  //#define TOUCH_SCREEN_CALIBRATION
 
   //#define TOUCH_CALIBRATION_X 12316
   //#define TOUCH_CALIBRATION_Y -8981

Marlin/Configuration_adv.h

@@ -638,7 +638,11 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN PC14
+
+#if MOTHERBOARD == BOARD_MKS_ROBIN_NANO_V3
+  #define E0_AUTO_FAN_PIN PC14
+#endif
+
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -706,7 +710,11 @@
  */
 #define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
+
+#if MOTHERBOARD == BOARD_MKS_ROBIN_NANO_V3
   #define CASE_LIGHT_PIN PE6                  // Override the default pin if needed
+#endif
+
   #define INVERT_CASE_LIGHT true              // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
@@ -1477,9 +1485,9 @@
   //#define SET_INTERACTION_TIME          // Add 'C' parameter to set time until next filament change or other user interaction
   #if ENABLED(SET_INTERACTION_TIME)
     #define SHOW_INTERACTION_TIME         // Display time until next user interaction ('C' = filament change)
-    #endif
-  //#define M73_REPORT                    // Report progress to host with 'M73'
   #endif
+  //#define M73_REPORT                    // Report progress to host with 'M73'
+#endif
 
 // LCD Print Progress options, multiple can be rotated depending on screen layout
 #if HAS_DISPLAY && EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY)
@@ -2622,7 +2630,11 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-#define ADVANCED_PAUSE_FEATURE
+
+#if MOTHERBOARD == BOARD_MKS_ROBIN_NANO_V3
+  #define ADVANCED_PAUSE_FEATURE
+#endif
+
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.

Marlin/Version.h

@@ -28,7 +28,7 @@
 /**
  * Marlin release version identifier
  */
-//#define SHORT_BUILD_VERSION "bugfix-2.1.x"
+#define SHORT_BUILD_VERSION "FBG6-2.1.1"
 
 /**
  * Verbose version identifier which should contain a reference to the location
@@ -46,15 +46,15 @@
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.
  */
-//#define MACHINE_NAME "3D Printer"
+#define MACHINE_NAME "Flying Bear Ghost 6"
 
 /**
  * The SOURCE_CODE_URL is the location where users will find the Marlin Source
  * Code which is installed on the device. In most cases —unless the manufacturer
  * has a distinct Github fork— the Source Code URL should just be the main
  * Marlin repository.
  */
-//#define SOURCE_CODE_URL "github.com/MarlinFirmware/Marlin"
+#define SOURCE_CODE_URL "github.com/adequator/Marlin-FBG6"
 
 /**
  * Default generic printer UUID.

Marlin/src/inc/Conditionals_LCD.h

@@ -1523,8 +1523,10 @@
     #define TFT_TOUCH_DEVICE_GT911
   #endif
 #elif ENABLED(TFT_GENERIC)
-  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
-  #if NONE(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320, TFT_RES_1024x600)
+  #ifndef TFT_DEFAULT_ORIENTATION
+    #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
+  #endif
+  #if NONE(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320, TFT_RES_320x480, TFT_RES_1024x600)
     #define TFT_RES_320x240
   #endif
   #if NONE(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI)

Marlin/src/inc/SanityCheck.h

@@ -3073,7 +3073,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   #endif
 #endif
 
-#if EITHER(MKS_TS35_V2_0, BTT_TFT35_SPI_V1_0, MKS_TS35_V2_0_VERTICAL) && SD_CONNECTION_IS(LCD)
+#if ANY(MKS_TS35_V2_0, BTT_TFT35_SPI_V1_0, MKS_TS35_V2_0_VERTICAL) && SD_CONNECTION_IS(LCD)
   #error "SDCARD_CONNECTION cannot be set to LCD for the enabled TFT. No available SD card reader."
 #endif
 

Marlin/src/lcd/extui/ui_api.cpp

@@ -1181,6 +1181,87 @@ namespace ExtUI {
     #endif
   }
 
+  void onStartup() {
+    /* Initialize the display module here. The following
+     * routines are available for access to the GPIO pins:
+     *
+     *   SET_OUTPUT(pin)
+     *   SET_INPUT_PULLUP(pin)
+     *   SET_INPUT(pin)
+     *   WRITE(pin,value)
+     *   READ(pin)
+     */
+  }
+  void onIdle() {}
+  void onPrinterKilled(FSTR_P const error, FSTR_P const component) {}
+  void onMediaInserted() {}
+  void onMediaError() {}
+  void onMediaRemoved() {}
+  void onPlayTone(const uint16_t frequency, const uint16_t duration) {}
+  void onPrintTimerStarted() {}
+  void onPrintTimerPaused() {}
+  void onPrintTimerStopped() {}
+  void onFilamentRunout(const extruder_t extruder) {}
+  void onUserConfirmRequired(const char * const msg) {}
+  void onStatusChanged(const char * const msg) {}
+
+  void onHomingStart() {}
+  void onHomingDone() {}
+  void onPrintDone() {}
+
+  void onFactoryReset() {}
+
+  void onStoreSettings(char *buff) {
+    // Called when saving to EEPROM (i.e. M500). If the ExtUI needs
+    // permanent data to be stored, it can write up to eeprom_data_size bytes
+    // into buff.
+
+    // Example:
+    //  static_assert(sizeof(myDataStruct) <= eeprom_data_size);
+    //  memcpy(buff, &myDataStruct, sizeof(myDataStruct));
+  }
+
+  void onLoadSettings(const char *buff) {
+    // Called while loading settings from EEPROM. If the ExtUI
+    // needs to retrieve data, it should copy up to eeprom_data_size bytes
+    // from buff
+
+    // Example:
+    //  static_assert(sizeof(myDataStruct) <= eeprom_data_size);
+    //  memcpy(&myDataStruct, buff, sizeof(myDataStruct));
+  }
+
+  void onPostprocessSettings() {
+    // Called after loading or resetting stored settings
+  }
+
+  void onSettingsStored(bool success) {
+    // Called after the entire EEPROM has been written,
+    // whether successful or not.
+  }
+
+  void onSettingsLoaded(bool success) {
+    // Called after the entire EEPROM has been read,
+    // whether successful or not.
+  }
+
+  #if HAS_PID_HEATING
+    void onPidTuning(const result_t rst) {
+      // Called for temperature PID tuning result
+      switch (rst) {
+        case PID_STARTED:          break;
+        case PID_BAD_EXTRUDER_NUM: break;
+        case PID_TEMP_TOO_HIGH:    break;
+        case PID_TUNING_TIMEOUT:   break;
+        case PID_DONE:             break;
+      }
+    }
+  #endif
+
+  void onSteppersDisabled() {}
+  void onSteppersEnabled()  {}
+
+
 } // namespace ExtUI
 
 // At the moment we hook into MarlinUI methods, but this could be cleaned up in the future