Update 5.4-2.1.x-imx to v5.4.73 from stable #160
Merged
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[ Upstream commit a81072a ] Inside __scif_pin_pages(), when map_flags != SCIF_MAP_KERNEL it will call pin_user_pages_fast() to map nr_pages. However, pin_user_pages_fast() might fail with a return value -ERRNO. The return value is stored in pinned_pages->nr_pages. which in turn is passed to unpin_user_pages(), which expects pinned_pages->nr_pages >=0, else disaster. Fix this by assigning pinned_pages->nr_pages to 0 if pin_user_pages_fast() returns -ERRNO. Fixes: ba612aa ("misc: mic: SCIF memory registration and unregistration") Cc: John Hubbard <[email protected]> Cc: Ira Weiny <[email protected]> Cc: Dan Carpenter <[email protected]> Reviewed-by: John Hubbard <[email protected]> Signed-off-by: Souptick Joarder <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 2759caa ] Recently we applied a fix to cover the whole OSS sequencer ioctls with the mutex for dealing with the possible races. This works fine in general, but in theory, this may lead to unexpectedly long stall if an ioctl like SNDCTL_SEQ_SYNC is issued and an event with the far future timestamp was queued. For fixing such a potential stall, this patch changes the mutex lock applied conditionally excluding such an ioctl command. Also, change the mutex_lock() with the interruptible version for user to allow escaping from the big-hammer mutex. Fixes: 80982c7 ("ALSA: seq: oss: Serialize ioctls") Suggested-by: Pavel Machek <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 362b939 ] When booting up on a Raspberry Pi 4 with Control Flow Integrity checking enabled, the following warning/panic happens: [ 1.626435] CFI failure (target: dwc2_set_bcm_params+0x0/0x4): [ 1.632408] WARNING: CPU: 0 PID: 32 at kernel/cfi.c:30 __cfi_check_fail+0x54/0x5c [ 1.640021] Modules linked in: [ 1.643137] CPU: 0 PID: 32 Comm: kworker/0:1 Not tainted 5.8.0-rc6-next-20200724-00051-g89ba619726de Freescale#1 [ 1.652693] Hardware name: Raspberry Pi 4 Model B Rev 1.2 (DT) [ 1.658637] Workqueue: events deferred_probe_work_func [ 1.663870] pstate: 60000005 (nZCv daif -PAN -UAO BTYPE=--) [ 1.669542] pc : __cfi_check_fail+0x54/0x5c [ 1.673798] lr : __cfi_check_fail+0x54/0x5c [ 1.678050] sp : ffff8000102bbaa0 [ 1.681419] x29: ffff8000102bbaa0 x28: ffffab09e21c7000 [ 1.686829] x27: 0000000000000402 x26: ffff0000f6e7c228 [ 1.692238] x25: 00000000fb7cdb0d x24: 0000000000000005 [ 1.697647] x23: ffffab09e2515000 x22: ffffab09e069a000 [ 1.703055] x21: 4c550309df1cf4c1 x20: ffffab09e2433c60 [ 1.708462] x19: ffffab09e160dc50 x18: ffff0000f6e8cc78 [ 1.713870] x17: 0000000000000041 x16: ffffab09e0bce6f8 [ 1.719278] x15: ffffab09e1c819b7 x14: 0000000000000003 [ 1.724686] x13: 00000000ffffefff x12: 0000000000000000 [ 1.730094] x11: 0000000000000000 x10: 00000000ffffffff [ 1.735501] x9 : c932f7abfc4bc600 x8 : c932f7abfc4bc600 [ 1.740910] x7 : 077207610770075f x6 : ffff0000f6c38f00 [ 1.746317] x5 : 0000000000000000 x4 : 0000000000000000 [ 1.751723] x3 : 0000000000000000 x2 : 0000000000000000 [ 1.757129] x1 : ffff8000102bb7d8 x0 : 0000000000000032 [ 1.762539] Call trace: [ 1.765030] __cfi_check_fail+0x54/0x5c [ 1.768938] __cfi_check+0x5fa6c/0x66afc [ 1.772932] dwc2_init_params+0xd74/0xd78 [ 1.777012] dwc2_driver_probe+0x484/0x6ec [ 1.781180] platform_drv_probe+0xb4/0x100 [ 1.785350] really_probe+0x228/0x63c [ 1.789076] driver_probe_device+0x80/0xc0 [ 1.793247] __device_attach_driver+0x114/0x160 [ 1.797857] bus_for_each_drv+0xa8/0x128 [ 1.801851] __device_attach.llvm.14901095709067289134+0xc0/0x170 [ 1.808050] bus_probe_device+0x44/0x100 [ 1.812044] deferred_probe_work_func+0x78/0xb8 [ 1.816656] process_one_work+0x204/0x3c4 [ 1.820736] worker_thread+0x2f0/0x4c4 [ 1.824552] kthread+0x174/0x184 [ 1.827837] ret_from_fork+0x10/0x18 CFI validates that all indirect calls go to a function with the same exact function pointer prototype. In this case, dwc2_set_bcm_params is the target, which has a parameter of type 'struct dwc2_hsotg *', but it is being implicitly cast to have a parameter of type 'void *' because that is the set_params function pointer prototype. Make the function pointer protoype match the definitions so that there is no more violation. Fixes: 7de1deb ("usb: dwc2: Remove platform static params") Link: ClangBuiltLinux#1107 Signed-off-by: Nathan Chancellor <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 3d3dc27 ] Freshly allocated memory contains garbage, better make sure to init all struct v2r1_disk_dqblk fields to avoid KMSAN report: BUG: KMSAN: uninit-value in qtree_entry_unused+0x137/0x1b0 fs/quota/quota_tree.c:218 CPU: 0 PID: 23373 Comm: syz-executor.1 Not tainted 5.9.0-rc4-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219 qtree_entry_unused+0x137/0x1b0 fs/quota/quota_tree.c:218 v2r1_mem2diskdqb+0x43d/0x710 fs/quota/quota_v2.c:285 qtree_write_dquot+0x226/0x870 fs/quota/quota_tree.c:394 v2_write_dquot+0x1ad/0x280 fs/quota/quota_v2.c:333 dquot_commit+0x4af/0x600 fs/quota/dquot.c:482 ext4_write_dquot fs/ext4/super.c:5934 [inline] ext4_mark_dquot_dirty+0x4d8/0x6a0 fs/ext4/super.c:5985 mark_dquot_dirty fs/quota/dquot.c:347 [inline] mark_all_dquot_dirty fs/quota/dquot.c:385 [inline] dquot_alloc_inode+0xc05/0x12b0 fs/quota/dquot.c:1755 __ext4_new_inode+0x8204/0x9d70 fs/ext4/ialloc.c:1155 ext4_tmpfile+0x41a/0x850 fs/ext4/namei.c:2686 vfs_tmpfile+0x2a2/0x570 fs/namei.c:3283 do_tmpfile fs/namei.c:3316 [inline] path_openat+0x4035/0x6a90 fs/namei.c:3359 do_filp_open+0x2b8/0x710 fs/namei.c:3395 do_sys_openat2+0xa88/0x1140 fs/open.c:1168 do_sys_open fs/open.c:1184 [inline] __do_compat_sys_openat fs/open.c:1242 [inline] __se_compat_sys_openat+0x2a4/0x310 fs/open.c:1240 __ia32_compat_sys_openat+0x56/0x70 fs/open.c:1240 do_syscall_32_irqs_on arch/x86/entry/common.c:80 [inline] __do_fast_syscall_32+0x129/0x180 arch/x86/entry/common.c:139 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:162 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:205 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c RIP: 0023:0xf7ff4549 Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90 RSP: 002b:00000000f55cd0cc EFLAGS: 00000296 ORIG_RAX: 0000000000000127 RAX: ffffffffffffffda RBX: 00000000ffffff9c RCX: 0000000020000000 RDX: 0000000000410481 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80 slab_alloc_node mm/slub.c:2907 [inline] slab_alloc mm/slub.c:2916 [inline] __kmalloc+0x2bb/0x4b0 mm/slub.c:3982 kmalloc include/linux/slab.h:559 [inline] getdqbuf+0x56/0x150 fs/quota/quota_tree.c:52 qtree_write_dquot+0xf2/0x870 fs/quota/quota_tree.c:378 v2_write_dquot+0x1ad/0x280 fs/quota/quota_v2.c:333 dquot_commit+0x4af/0x600 fs/quota/dquot.c:482 ext4_write_dquot fs/ext4/super.c:5934 [inline] ext4_mark_dquot_dirty+0x4d8/0x6a0 fs/ext4/super.c:5985 mark_dquot_dirty fs/quota/dquot.c:347 [inline] mark_all_dquot_dirty fs/quota/dquot.c:385 [inline] dquot_alloc_inode+0xc05/0x12b0 fs/quota/dquot.c:1755 __ext4_new_inode+0x8204/0x9d70 fs/ext4/ialloc.c:1155 ext4_tmpfile+0x41a/0x850 fs/ext4/namei.c:2686 vfs_tmpfile+0x2a2/0x570 fs/namei.c:3283 do_tmpfile fs/namei.c:3316 [inline] path_openat+0x4035/0x6a90 fs/namei.c:3359 do_filp_open+0x2b8/0x710 fs/namei.c:3395 do_sys_openat2+0xa88/0x1140 fs/open.c:1168 do_sys_open fs/open.c:1184 [inline] __do_compat_sys_openat fs/open.c:1242 [inline] __se_compat_sys_openat+0x2a4/0x310 fs/open.c:1240 __ia32_compat_sys_openat+0x56/0x70 fs/open.c:1240 do_syscall_32_irqs_on arch/x86/entry/common.c:80 [inline] __do_fast_syscall_32+0x129/0x180 arch/x86/entry/common.c:139 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:162 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:205 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c Fixes: 498c601 ("quota: Implement quota format with 64-bit space and inode limits") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Eric Dumazet <[email protected]> Cc: Jan Kara <[email protected]> Signed-off-by: Jan Kara <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit f97769f ] logical address can be either assigned by the SLIMBus controller or the core. Core uses IDA in cases where get_addr callback is not provided by the controller. Core already has this check while allocating IDR, however during absence reporting this is not checked. This patch fixes this issue. Fixes: 46a2bb5 ("slimbus: core: Add slim controllers support") Signed-off-by: Srinivas Kandagatla <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit df2c471 ] Let the controller logic decide when to enter into clock pause mode! Entering in to pause mode during unregistration does not really make sense as the controller is totally going down at that point in time. Fixes: 4b14e62 ("slimbus: Add support for 'clock-pause' feature") Signed-off-by: Srinivas Kandagatla <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 709ec3f ] In QMI new server notification we enable the NGD however during delete server notification we do not disable the NGD. This can lead to multiple instances of NGD being enabled, so make sure that we disable NGD in delete server callback to fix this issue! Fixes: 917809e ("slimbus: ngd: Add qcom SLIMBus NGD driver") Signed-off-by: Srinivas Kandagatla <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 22a1614 ] Instantiate snd_soc_dai_driver for independent symmetric control. Otherwise the symmetric setting may be overwritten by other instance. Fixes: 08fdf65 ("ASoC: fsl_sai: Add asynchronous mode support") Signed-off-by: Shengjiu Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Mark Brown <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 505f394 ] With commit 4f38821 hid-input started clearing of "ignored" usages to avoid using garbage that might have been left in them. However "battery strength" usages should not be ignored, as we do want to use them. Fixes: 4f38821 ("HID: hid-input: clear unmapped usages") Reported-by: Kenneth Albanowski <[email protected]> Tested-by: Kenneth Albanowski <[email protected]> Signed-off-by: Dmitry Torokhov <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
…ell() [ Upstream commit fc9eec4 ] Fix missing 'kfree_const(cell->name)' when call to nvmem_cell_info_to_nvmem_cell() in several places: * after nvmem_cell_info_to_nvmem_cell() failed during nvmem_add_cells() * during nvmem_device_cell_{read,write} when cell->name is kstrdup'ed() without calling kfree_const() at the end, but really there is no reason to do that 'dup, because the cell instance is allocated on the stack for some short period to be read/write without exposing it to the caller. So the new nvmem_cell_info_to_nvmem_cell_nodup() helper is introduced which is used to convert cell_info -> cell without name duplication as a lighweight version of nvmem_cell_info_to_nvmem_cell(). Fixes: e2a5402 ("nvmem: Add nvmem_device based consumer apis.") Reviewed-by: Srinivas Kandagatla <[email protected]> Acked-by: Srinivas Kandagatla <[email protected]> Signed-off-by: Vadym Kochan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 6c8b6e4 ] The SRG min and max offset won't present when SRG Information Present of SR control field of Spatial Reuse Parameter Set element set to 0. Per spec. IEEE802.11ax D7.0, SRG OBSS PD Min Offset ≤ SRG OBSS PD Max Offset. Hence fix the constrain check to allow same values in both offset and also call appropriate nla_get function to read the values. Fixes: 796e90f ("cfg80211: add support for parsing OBBS_PD attributes") Signed-off-by: Rajkumar Manoharan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 716f565 ] When coresight_build_path() fails on all the cpus, etm_setup_aux calls etm_free_aux() to free allocated event_data. WARN_ON(cpumask_empty(mask) will be triggered since cpu mask is empty. Check event_data->snk_config is not NULL first to avoid this warning. Fixes: f5200aa ("coresight: perf: Refactor function free_event_data()") Reviewed-by: Mike Leach <[email protected]> Reviewed-by: Suzuki K Poulose <[email protected]> Signed-off-by: Tingwei Zhang <[email protected]> Signed-off-by: Mathieu Poirier <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit b9cd795 ] Set up the speed according to crq->query_phys_parms.rsp.speed. Fix IBMVNIC_10GBPS typo. Fixes: f8d6ae0 ("ibmvnic: Report actual backing device speed and duplex values") Signed-off-by: Lijun Pan <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 63f6982 ] Currently if an unsupported iftype is detected the error return path does not free the cmd_skb leading to a resource leak. Fix this by free'ing cmd_skb. Addresses-Coverity: ("Resource leak") Fixes: 805b28c ("qtnfmac: prepare for AP_VLAN interface type support") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit c537d34 ] When the ADC is runtime suspended and starting a conversion, the stm32-adc driver calls pm_runtime_get_sync() that gets cascaded to the parent (e.g. runtime resume of stm32-adc-core driver). This also kicks the autosuspend delay (e.g. 2s) of the parent. Once the ADC is active, calling pm_runtime_get_sync() again (upon a new capture) won't kick the autosuspend delay for the parent (stm32-adc-core driver) as already active. Currently, this makes the stm32-adc-core driver go in suspend state every 2s when doing slow polling. As an example, doing a capture, e.g. cat in_voltageY_raw at a 0.2s rate, the auto suspend delay for the parent isn't refreshed. Once it expires, the parent immediately falls into runtime suspended state, in between two captures, as soon as the child driver falls into runtime suspend state: - e.g. after 2s, + child calls pm_runtime_put_autosuspend() + 100ms autosuspend delay of the child. - stm32-adc-core switches off regulators, clocks and so on. - They get switched on back again 100ms later in this example (at 2.2s). So, use runtime_idle() callback in stm32-adc-core driver to call pm_runtime_mark_last_busy() for the parent driver (stm32-adc-core), to avoid this. Fixes: 9bdbb11 ("iio: adc: stm32-adc: add power management support") Signed-off-by: Fabrice Gasnier <[email protected]> Reviewed-by: Ulf Hansson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jonathan Cameron <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit a53b59e ] enic_dev_wait() has a BUG_ON(in_interrupt()). Chasing the callers of enic_dev_wait() revealed the gems of enic_reset() and enic_tx_hang_reset() which are both invoked through work queues in order to be able to call rtnl_lock(). So far so good. After locking rtnl both functions acquire enic::enic_api_lock which serializes against the (ab)use from infiniband. This is where the trainwreck starts. enic::enic_api_lock is a spin_lock() which implicitly disables preemption, but both functions invoke a ton of functions under that lock which can sleep. The BUG_ON(in_interrupt()) does not trigger in that case because it can't detect the preempt disabled condition. This clearly has never been tested with any of the mandatory debug options for 7+ years, which would have caught that for sure. Cure it by adding a enic_api_busy member to struct enic, which is modified and evaluated with enic::enic_api_lock held. If enic_api_devcmd_proxy_by_index() observes enic::enic_api_busy as true, it drops enic::enic_api_lock and busy waits for enic::enic_api_busy to become false. It would be smarter to wait for a completion of that busy period, but enic_api_devcmd_proxy_by_index() is called with other spin locks held which obviously can't sleep. Remove the BUG_ON(in_interrupt()) check as well because it's incomplete and with proper debugging enabled the problem would have been caught from the debug checks in schedule_timeout(). Fixes: 0b03856 ("drivers/net: enic: Add an interface for USNIC to interact with firmware") Signed-off-by: Thomas Gleixner <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 8ce24f8 ] This code should clean up if sm501_init_dev() fails. Fixes: b6d6454 ("[PATCH] mfd: SM501 core driver") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Lee Jones <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 903b3f9 ] A print in the remain on channel code was too long and caused a WARNING, split it. Signed-off-by: Emmanuel Grumbach <[email protected]> Fixes: dc28e12 ("iwlwifi: mvm: ROC: Extend the ROC max delay duration & limit ROC duration") Signed-off-by: Luca Coelho <[email protected]> Link: https://lore.kernel.org/r/iwlwifi.20200930102759.58d57c0bdc68.Ib06008665e7bf1199c360aa92691d9c74fb84990@changeid Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 986499b ] Currently, SuperSpeed NCM gadgets report a speed of 851 Mbps in USB_CDC_NOTIFY_SPEED_CHANGE. But the calculation appears to assume 16 packets per microframe, and USB 3 and above no longer use microframes. Maximum speed is actually much higher. On a direct connection, theoretical throughput is at most 3.86 Gbps for gen1x1 and 9.36 Gbps for gen2x1, and I have seen gadget->host iperf throughput of >2 Gbps for gen1x1 and >4 Gbps for gen2x1. Unfortunately the ConnectionSpeedChange defined in the CDC spec only uses 32-bit values, so we can't report accurate numbers for 10Gbps and above. So, report 3.75Gbps for SuperSpeed (which is roughly maximum theoretical performance) and 4.25Gbps for SuperSpeed Plus (which is close to the maximum that we can report in a 32-bit unsigned integer). This results in: [50879.191272] cdc_ncm 2-2:1.0 enx228b127e050c: renamed from usb0 [50879.234778] cdc_ncm 2-2:1.0 enx228b127e050c: 3750 mbit/s downlink 3750 mbit/s uplink on SuperSpeed and: [50798.434527] cdc_ncm 8-2:1.0 enx228b127e050c: renamed from usb0 [50798.524278] cdc_ncm 8-2:1.0 enx228b127e050c: 4250 mbit/s downlink 4250 mbit/s uplink on SuperSpeed Plus. Fixes: 1650113 ("usb: gadget: f_ncm: add SuperSpeed descriptors for CDC NCM") Reviewed-by: Maciej Żenczykowski <[email protected]> Signed-off-by: Lorenzo Colitti <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 4eea21d ] The u_ether driver has a qmult setting that multiplies the transmit queue length (which by default is 2). The intent is that it should be enabled at high/super speed, but because the code does not explicitly check for USB_SUPER_PLUS, it is disabled at that speed. Fix this by ensuring that the queue multiplier is enabled for any wired link at high speed or above. Using >= for USB_SPEED_* constants seems correct because it is what the gadget_is_xxxspeed functions do. The queue multiplier substantially helps performance at higher speeds. On a direct SuperSpeed Plus link to a Linux laptop, iperf3 single TCP stream: Before (qmult=1): 1.3 Gbps After (qmult=5): 3.2 Gbps Fixes: 04617db ("usb: gadget: add SS descriptors to Ethernet gadget") Reviewed-by: Maciej Żenczykowski <[email protected]> Signed-off-by: Lorenzo Colitti <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit ab10c22 ] When dumping wiphy information, we try to split the data into many submessages, but for old userspace we still support the old mode where this doesn't happen. However, in this case we were not resetting our state correctly and dumping multiple messages for each wiphy, which would have broken such older userspace. This was broken pretty much immediately afterwards because it only worked in the original commit where non-split dumps didn't have any more data than split dumps... Fixes: fe1abaf ("nl80211: re-add channel width and extended capa advertising") Signed-off-by: Johannes Berg <[email protected]> Link: https://lore.kernel.org/r/20200928130717.3e6d9c6bada2.Ie0f151a8d0d00a8e1e18f6a8c9244dd02496af67@changeid Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit b2c586e ] In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet corresponds to single descriptor. Descriptor limit set to mps and desc chain limit set to mps * MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate transfer size should be considered correction value for each descriptor. In start request function, if "continue" is true then dma buffer address should be incremmented by offset for all type of transfers, not only for Control DATA_OUT transfers. Fixes: cf77b5f ("usb: dwc2: gadget: Transfer length limit checking for DDMA") Fixes: e02f9aa ("usb: dwc2: gadget: EP 0 specific DDMA programming") Fixes: aa3e8bc ("usb: dwc2: gadget: DDMA transfer start and complete") Signed-off-by: Minas Harutyunyan <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 61741d8 ] Corrects drivers/target/target_core_user.c:688:6: warning: 'page' may be used uninitialized. Link: https://lore.kernel.org/r/[email protected] Fixes: 3c58f73 ("scsi: target: tcmu: Optimize use of flush_dcache_page") Cc: Mike Christie <[email protected]> Acked-by: Mike Christie <[email protected]> Signed-off-by: John Donnelly <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 38b2db5 ] The be_fill_queue() function can only fail when "eq_vaddress" is NULL and since it's non-NULL here that means the function call can't fail. But imagine if it could, then in that situation we would want to store the "paddr" so that dma memory can be released. Link: https://lore.kernel.org/r/20200928091300.GD377727@mwanda Fixes: bfead3b ("[SCSI] be2iscsi: Adding msix and mcc_rings V3") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 8fe7990 ] On an error exit path, a negative error code should be returned instead of a positive return value. Fixes: 90b2d4f ("ipmi_si: Remove hacks for adding a dummy platform devices") Cc: Corey Minyard <[email protected]> Signed-off-by: Tianjia Zhang <[email protected]> Message-Id: <[email protected]> Signed-off-by: Corey Minyard <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit c071afc ] Remove PSU EEPROM configuration for systems class equipped with Mellanox chip Spectrume-2. Till now all the systems from this class used few types of power units, all equipped with EEPROM device with address space two bytes. Thus, all these devices have been handled by EEPROM driver "24c32". There is a new requirement is to support power unit replacement by "off the shelf" device, matching electrical required parameters. Such device could be equipped with different EEPROM type, which could be one byte address space addressing or even could be not equipped with EEPROM. In such case "24c32" will not work. Fixes: 1bd42d9 ("platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems") Signed-off-by: Vadim Pasternak <[email protected]> Reviewed-by: Hans de Goede <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 53708f4 ] clang static analysis reports this problem: sdio.c:2403:3: warning: Attempt to free released memory kfree(card->mpa_rx.buf); ^~~~~~~~~~~~~~~~~~~~~~~ When mwifiex_init_sdio() fails in its first call to mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it again. If the second alloc of mpa_tx.buf fails, the error handler will try to free the old, previously freed mpa_rx.buf. Reviewing the code, it looks like a second double free would happen with mwifiex_cleanup_sdio(). So set both pointers to NULL when they are freed. Fixes: 5e6e3a9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Tom Rix <[email protected]> Reviewed-by: Brian Norris <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 7980d2e ] fq qdisc requires tstamp to be cleared in forwarding path Reported-by: Evgeny B <[email protected]> Link: https://bugzilla.kernel.org/show_bug.cgi?id=209427 Suggested-by: Eric Dumazet <[email protected]> Fixes: 8203e2d ("net: clear skb->tstamp in forwarding paths") Fixes: fb420d5 ("tcp/fq: move back to CLOCK_MONOTONIC") Fixes: 80b14de ("net: Add a new socket option for a future transmit time.") Signed-off-by: Julian Anastasov <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 3af5f0f ] kmalloc returns KSEG0 addresses so convert back from KSEG1 in kfree. Also make sure array is freed when the driver is unloaded from the kernel. Fixes: ef11291 ("Add support the Korina (IDT RC32434) Ethernet MAC") Signed-off-by: Valentin Vidic <[email protected]> Acked-by: Willem de Bruijn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 0d9826b ] Dump vlan tag and proto for the usual vlan offload case if the NF_LOG_MACDECODE flag is set on. Without this information the logging is misleading as there is no reference to the VLAN header. [12716.993704] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0800 SRC=192.168.10.2 DST=172.217.168.163 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=2548 DF PROTO=TCP SPT=55848 DPT=80 WINDOW=501 RES=0x00 ACK FIN URGP=0 [12721.157643] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0806 ARP HTYPE=1 PTYPE=0x0800 OPCODE=2 MACSRC=86:6c:92:ea:d6:73 IPSRC=192.168.10.2 MACDST=0e:3b:eb:86:73:76 IPDST=192.168.10.1 Fixes: 83e96d4 ("netfilter: log: split family specific code to nf_log_{ip,ip6,common}.c files") Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit a49145a ] A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting or yres setting in struct fb_var_screeninfo will result in a KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as the margins are being cleared. The margins are cleared in chunks and if the xres setting or yres setting is a value of zero upto the chunk size, the failure will occur. Add a margin check to validate xres and yres settings. Signed-off-by: George Kennedy <[email protected]> Reported-by: [email protected] Reviewed-by: Dan Carpenter <[email protected]> Cc: Dhaval Giani <[email protected]> Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit db33235 ] ipwireless_send_packet() can only return 0 on success and -ENOMEM on error, the caller should check non zero for error condition Signed-off-by: Tong Zhang <[email protected]> Acked-by: David Sterba <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit d33fe77 ] When kmalloc() on buf fails, urb should be freed just like when kmalloc() on dr fails. Signed-off-by: Dinghao Liu <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit c5a8a84 ] do_ip_vs_set_ctl() is referencing uninitialized stack value when `len` is zero. Fix it. Reported-by: [email protected] Link: https://syzkaller.appspot.com/bug?id=46ebfb92a8a812621a001ef04d90dfa459520fe2 Suggested-by: Julian Anastasov <[email protected]> Signed-off-by: Peilin Ye <[email protected]> Acked-by: Julian Anastasov <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit e9d4709 ] When a usrjquota or grpjquota mount option is used multiple times, we will leak memory allocated for the file name. Make sure the last setting is used and all the previous ones are properly freed. Reported-by: [email protected] Signed-off-by: Jan Kara <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 621a3a8 ] syzbot is reporting that del_timer_sync() is called from mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without checking timer_setup() from mwifiex_usb_tx_init() was called [1]. Ganapathi Bhat proposed a possibly cleaner fix, but it seems that that fix was forgotten [2]. "grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that currently there are 28 locations which call del_timer[_sync]() only if that timer's function field was initialized (because timer_setup() sets that timer's function field). Therefore, let's use same approach here. [1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959 [2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com Reported-by: syzbot <[email protected]> Cc: Ganapathi Bhat <[email protected]> Cc: Brian Norris <[email protected]> Signed-off-by: Tetsuo Handa <[email protected]> Reviewed-by: Brian Norris <[email protected]> Acked-by: Ganapathi Bhat <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit ed93f97 ] Add AE-7 quirk data for setting of microphone. The AE-7 has no front panel connector, so only rear-mic/line-in have new commands. Signed-off-by: Connor McAdams <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 620f08e ] Add a new PCI subsystem ID for the SoundBlaster AE-7 card. Signed-off-by: Connor McAdams <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 9e68ccc ] Eliminate kernel panics when getting invalid responses from controller. Take controller offline instead of causing kernel panics. Link: https://lore.kernel.org/r/159622929306.30579.16523318707596752828.stgit@brunhilda Reviewed-by: Scott Teel <[email protected]> Reviewed-by: Scott Benesh <[email protected]> Reviewed-by: Prasad Munirathnam <[email protected]> Reviewed-by: Martin Wilck <[email protected]> Signed-off-by: Kevin Barnett <[email protected]> Signed-off-by: Don Brace <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 6c15141 ] When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL, we should destroy the workqueue. Reported-by: Hulk Robot <[email protected]> Signed-off-by: Wang Yufen <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit fbc2994 ] usb_kill_anchored_urbs() is commonly used to cancel all URBs on an anchor just before releasing resources which the URBs rely on. By doing so, users of this function rely on that no completer callbacks will take place from any URB on the anchor after it returns. However if this function is called in parallel with __usb_hcd_giveback_urb processing a URB on the anchor, the latter may call the completer callback after usb_kill_anchored_urbs() returns. This can lead to a kernel panic due to use after release of memory in interrupt context. The race condition is that __usb_hcd_giveback_urb() first unanchors the URB and then makes the completer callback. Such URB is hence invisible to usb_kill_anchored_urbs(), allowing it to return before the completer has been called, since the anchor's urb_list is empty. Even worse, if the racing completer callback resubmits the URB, it may remain in the system long after usb_kill_anchored_urbs() returns. Hence list_empty(&anchor->urb_list), which is used in the existing while-loop, doesn't reliably ensure that all URBs of the anchor are gone. A similar problem exists with usb_poison_anchored_urbs() and usb_scuttle_anchored_urbs(). This patch adds an external do-while loop, which ensures that all URBs are indeed handled before these three functions return. This change has no effect at all unless the race condition occurs, in which case the loop will busy-wait until the racing completer callback has finished. This is a rare condition, so the CPU waste of this spinning is negligible. The additional do-while loop relies on usb_anchor_check_wakeup(), which returns true iff the anchor list is empty, and there is no __usb_hcd_giveback_urb() in the system that is in the middle of the unanchor-before-complete phase. The @suspend_wakeups member of struct usb_anchor is used for this purpose, which was introduced to solve another problem which the same race condition causes, in commit 6ec4147 ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up till completion is done"). The surely_empty variable is necessary, because usb_anchor_check_wakeup() must be called with the lock held to prevent races. However the spinlock must be released and reacquired if the outer loop spins with an empty URB list while waiting for the unanchor-before-complete passage to finish: The completer callback may very well attempt to take the very same lock. To summarize, using usb_anchor_check_wakeup() means that the patched functions can return only when the anchor's list is empty, and there is no invisible URB being processed. Since the inner while loop finishes on the empty list condition, the new do-while loop will terminate as well, except for when the said race condition occurs. Signed-off-by: Eli Billauer <[email protected]> Acked-by: Oliver Neukum <[email protected]> Acked-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
…onfig() [ Upstream commit 89dd87a ] If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync() and ufshcd_hold() will cause a race condition. Fix this by removing the unnecessary calls of pm_runtime_get_sync() and ufshcd_hold(). Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hongwu Su <[email protected]> Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit e8ee6c8 ] DW DMA IP-core provides a way to synthesize the DMA controller with channels having different parameters like maximum burst-length, multi-block support, maximum data width, etc. Those parameters both explicitly and implicitly affect the channels performance. Since DMA slave devices might be very demanding to the DMA performance, let's provide a functionality for the slaves to be assigned with DW DMA channels, which performance according to the platform engineer fulfill their requirements. After this patch is applied it can be done by passing the mask of suitable DMA-channels either directly in the dw_dma_slave structure instance or as a fifth cell of the DMA DT-property. If mask is zero or not provided, then there is no limitation on the channels allocation. For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first two channels are synthesized with max burst length of 16, while the rest of the channels have been created with max-burst-len=4. It would seem that the first two channels must be faster than the others and should be more preferable for the time-critical DMA slave devices. In practice it turned out that the situation is quite the opposite. The channels with max-burst-len=4 demonstrated a better performance than the channels with max-burst-len=16 even when they both had been initialized with the same settings. The performance drop of the first two DMA-channels made them unsuitable for the DW APB SSI slave device. No matter what settings they are configured with, full-duplex SPI transfers occasionally experience the Rx FIFO overflow. It means that the DMA-engine doesn't keep up with incoming data pace even though the SPI-bus is enabled with speed of 25MHz while the DW DMA controller is clocked with 50MHz signal. There is no such problem has been noticed for the channels synthesized with max-burst-len=4. Signed-off-by: Serge Semin <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Vinod Koul <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 6d9459d ] CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion. In other words it determines when to start pushing data out of a DW DMAC channel FIFO to a destination peripheral or from a source peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one for all DW DMAC channels. It means they are tuned to flush data out of FIFO (to a memory peripheral or by accepting the burst transaction requests) when FIFO is at least half-full (except at the end of the block transfer, when FIFO-flush mode is activated) and are configured to get data to the FIFO when it's at least half-empty. Such configuration is a good choice when there is no slave device involved in the DMA transfers. In that case the number of bursts per block is less than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve. But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1, since DW DMAC will wait for the channel FIFO contents to be either half-full or half-empty depending on having the destination or the source transfers. Such latencies might be dangerous in case if the DMA transfers are expected to be performed from/to a slave device. Since normally peripheral devices keep data in internal FIFOs, any latency at some critical moment may cause one being overflown and consequently losing data. This especially concerns a case when either a peripheral device is relatively fast or the DW DMAC engine is relatively slow with respect to the incoming data pace. In order to solve problems, which might be caused by the latencies described above, let's enable the FIFO half-full/half-empty "FIFO readiness" criterion only for DMA transfers with no slave device involved. Thanks to the commit 99ba8b9 ("dmaengine: dw: Initialize channel before each transfer") we can freely do that in the generic dw_dma_initialize_chan() method. Signed-off-by: Serge Semin <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Vinod Koul <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit bad60b8 ] The idx in __ath10k_htt_rx_ring_fill_n function lives in consistent dma region writable by the device. Malfunctional or malicious device could manipulate such idx to have a OOB write. Either by htt->rx_ring.netbufs_ring[idx] = skb; or by ath10k_htt_set_paddrs_ring(htt, paddr, idx); The idx can also be negative as it's signed, giving a large memory space to write to. It's possibly exploitable by corruptting a legit pointer with a skb pointer. And then fill skb with payload as rougue object. Part of the log here. Sometimes it appears as UAF when writing to a freed memory by chance. [ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0 [ 15.595483] #PF: supervisor write access in kernel mode [ 15.596250] #PF: error_code(0x0002) - not-present page [ 15.597013] PGD 0 P4D 0 [ 15.597395] Oops: 0002 [Freescale#1] SMP KASAN PTI [ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 Freescale#69 [ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core] [ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n (linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core Signed-off-by: Zekun Shen <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit 3bd57b9 ] Fixes gcc warning: passing argument 1 of 'kfree' makes pointer from integer without a cast Fixes: 3af5f0f ("net: korina: fix kfree of rx/tx descriptor array") Reported-by: kernel test robot <[email protected]> Signed-off-by: Valentin Vidic <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
[ Upstream commit a04f0ec ] The only time that our Bridgeport role should change is when we change the configuration ourselves. In which case we also adjust our internal state tracking, no need to do it again when we receive the corresponding event. Removing the locked section helps a subsequent patch that needs to flush the workqueue while under sbp_lock. It would be nice to raise a warning here in case HW does weird things after all, but this could end up generating false-positives when we change the configuration ourselves. Suggested-by: Alexandra Winter <[email protected]> Signed-off-by: Julian Wiedmann <[email protected]> Reviewed-by: Alexandra Winter <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
commit 9ea40db upstream. The 2nd and 3rd parameter were wrongly used, and cause kernel abort when doing kgdb debug. Fixes: 1da17d7 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs") Cc: stable <[email protected]> Signed-off-by: Peng Fan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 29788ab upstream. The watermark is set to 1, so we need to input two chars to trigger RDRF using the original logic. With the new logic, we could always get the char when there is data in FIFO. Suggested-by: Fugang Duan <[email protected]> Signed-off-by: Peng Fan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit a4f8843 upstream. The ES58X devices has a CDC ACM interface (used for debug purpose). During probing, the device is thus recognized as USB Modem (CDC ACM), preventing the etas-es58x module to load: usbcore: registered new interface driver etas_es58x usb 1-1.1: new full-speed USB device number 14 using xhci_hcd usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00 usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1.1: Product: ES581.4 usb 1-1.1: Manufacturer: ETAS GmbH usb 1-1.1: SerialNumber: 2204355 cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device Thus, these have been added to the ignore list in drivers/usb/class/cdc-acm.c N.B. Future firmware release of the ES58X will remove the CDC-ACM interface. `lsusb -v` of the three devices variant (ES581.4, ES582.1 and ES584.1): Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x108c Robert Bosch GmbH idProduct 0x0159 bcdDevice 1.00 iManufacturer 1 ETAS GmbH iProduct 2 ES581.4 iSerial 3 2204355 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0035 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Bus Powered Configuration bmAttributes 0x80 (Bus Powered) MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 0 iInterface 4 ACM Control Interface CDC Header: bcdCDC 1.10 CDC Call Management: bmCapabilities 0x01 call management bDataInterface 0 CDC ACM: bmCapabilities 0x06 sends break line coding and serial state Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0010 1x 16 bytes bInterval 10 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Device Status: 0x0000 (Bus Powered) Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x108c Robert Bosch GmbH idProduct 0x0168 bcdDevice 1.00 iManufacturer 1 ETAS GmbH iProduct 2 ES582 iSerial 3 0108933 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0043 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Union: bMasterInterface 0 bSlaveInterface 1 CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 16 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x108c Robert Bosch GmbH idProduct 0x0169 bcdDevice 1.00 iManufacturer 1 ETAS GmbH iProduct 2 ES584.1 iSerial 3 0100320 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0043 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Union: bMasterInterface 0 bSlaveInterface 1 CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 16 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Signed-off-by: Vincent Mailhol <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 37d2a36 upstream. syzbot is reporting hung task at wdm_flush() [1], for there is a circular dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget cannot be called unless close() for /dev/cdc-wdm0 completes. Tetsuo Handa considered that such circular dependency is an usage error [2] which corresponds to an unresponding broken hardware [3]. But Alan Stern responded that we should be prepared for such hardware [4]. Therefore, this patch changes wdm_flush() to use wait_event_interruptible_timeout() which gives up after 30 seconds, for hardware that remains silent must be ignored. The 30 seconds are coming out of thin air. Changing wait_event() to wait_event_interruptible_timeout() makes error reporting from close() syscall less reliable. To compensate it, this patch also implements wdm_fsync() which does not use timeout. Those who want to be very sure that data has gone out to the device are now advised to call fsync(), with a caveat that fsync() can return -EINVAL when running on older kernels which do not implement wdm_fsync(). This patch also fixes three more problems (listed below) found during exhaustive discussion and testing. Since multiple threads can concurrently call wdm_write()/wdm_flush(), we need to use wake_up_all() whenever clearing WDM_IN_USE in order to make sure that all waiters are woken up. Also, error reporting needs to use fetch-and-clear approach in order not to report same error for multiple times. Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well check WDM_DISCONNECTING. In wdm_flush(), since locks are not held, it is not safe to dereference desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus, remove dev_err() from wdm_flush(). [1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186 [2] https://lkml.kernel.org/r/[email protected] [3] https://lkml.kernel.org/r/[email protected] [4] https://lkml.kernel.org/r/[email protected] [5] https://lkml.kernel.org/r/[email protected] Reported-by: syzbot <[email protected]> Cc: stable <[email protected]> Co-developed-by: Tetsuo Handa <[email protected]> Signed-off-by: Tetsuo Handa <[email protected]> Signed-off-by: Oliver Neukum <[email protected]> Cc: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 98df91f upstream. The interrupt may occur during the gadget deletion, it fixes the below oops. [ 2394.974604] configfs-gadget gadget: suspend [ 2395.042578] configfs-gadget 5b130000.usb: unregistering UDC driver [g1] [ 2395.382562] irq 229: nobody cared (try booting with the "irqpoll" option) [ 2395.389362] CPU: 0 PID: 301 Comm: kworker/u12:6 Not tainted 5.8.0-rc3-next-20200703-00060-g2f13b83cbf30-dirty Freescale#456 [ 2395.399712] Hardware name: Freescale i.MX8QM MEK (DT) [ 2395.404782] Workqueue: 2-0051 tcpm_state_machine_work [ 2395.409832] Call trace: [ 2395.412289] dump_backtrace+0x0/0x1d0 [ 2395.415950] show_stack+0x1c/0x28 [ 2395.419271] dump_stack+0xbc/0x118 [ 2395.422678] __report_bad_irq+0x50/0xe0 [ 2395.426513] note_interrupt+0x2cc/0x38c [ 2395.430355] handle_irq_event_percpu+0x88/0x90 [ 2395.434800] handle_irq_event+0x4c/0xe8 [ 2395.438640] handle_fasteoi_irq+0xbc/0x168 [ 2395.442740] generic_handle_irq+0x34/0x48 [ 2395.446752] __handle_domain_irq+0x68/0xc0 [ 2395.450846] gic_handle_irq+0x64/0x150 [ 2395.454596] el1_irq+0xb8/0x180 [ 2395.457733] __do_softirq+0xac/0x3b8 [ 2395.461310] irq_exit+0xc0/0xe0 [ 2395.464448] __handle_domain_irq+0x6c/0xc0 [ 2395.468540] gic_handle_irq+0x64/0x150 [ 2395.472295] el1_irq+0xb8/0x180 [ 2395.475436] _raw_spin_unlock_irqrestore+0x14/0x48 [ 2395.480232] usb_gadget_disconnect+0x120/0x140 [ 2395.484678] usb_gadget_remove_driver+0xb4/0xd0 [ 2395.489208] usb_del_gadget+0x6c/0xc8 [ 2395.492872] cdns3_gadget_exit+0x5c/0x120 [ 2395.496882] cdns3_role_stop+0x60/0x90 [ 2395.500634] cdns3_role_set+0x64/0xd8 [ 2395.504301] usb_role_switch_set_role.part.0+0x3c/0x90 [ 2395.509444] usb_role_switch_set_role+0x20/0x30 [ 2395.513978] tcpm_mux_set+0x60/0xf8 [ 2395.517470] tcpm_reset_port+0xa4/0xf0 [ 2395.521222] tcpm_detach.part.0+0x44/0x50 [ 2395.525227] tcpm_state_machine_work+0x8b0/0x2360 [ 2395.529932] process_one_work+0x1c8/0x470 [ 2395.533939] worker_thread+0x50/0x420 [ 2395.537603] kthread+0x148/0x168 [ 2395.540830] ret_from_fork+0x10/0x18 [ 2395.544399] handlers: [ 2395.546671] [<000000008dea28da>] cdns3_wakeup_irq [ 2395.551375] [<000000009fee5c61>] cdns3_drd_irq threaded [<000000005148eaec>] cdns3_drd_thread_irq [ 2395.560255] Disabling IRQ Freescale#229 [ 2395.563454] configfs-gadget gadget: unbind function 'Mass Storage Function'/000000000132f835 [ 2395.563657] configfs-gadget gadget: unbind [ 2395.563917] udc 5b130000.usb: releasing '5b130000.usb' Fixes: 7733f6c ("usb: cdns3: Add Cadence USB3 DRD Driver") Cc: <[email protected]> Acked-by: Roger Quadros <[email protected]> Signed-off-by: Peter Chen <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 284f52a upstream. SPI eeproms are addressed by byte. Signed-off-by: Christian Eggers <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
[ Upstream commit 7974ecd ] Currently, enabling f_ncm at SuperSpeed Plus speeds results in an oops in config_ep_by_speed because ncm_set_alt passes in NULL ssp_descriptors. Fix this by re-using the SuperSpeed descriptors. This is safe because usb_assign_descriptors calls usb_copy_descriptors. Tested: enabled f_ncm on a dwc3 gadget and 10Gbps link, ran iperf Reviewed-by: Maciej Żenczykowski <[email protected]> Signed-off-by: Lorenzo Colitti <[email protected]> Signed-off-by: Felipe Balbi <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Tested-by: Linux Kernel Functional Testing <[email protected]> Tested-by: Guenter Roeck <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
This is the 5.4.73 stable release Conflicts: - arch/arm/boot/dts/imx6sl.dtsi: Commit [a1767c9] in NXP tree is now covered with commit [5c4c2f4] from upstream. - drivers/gpu/drm/mxsfb/mxsfb_drv.c: Resolve merge hunk for patch [ed8b90d] from upstream - drivers/media/i2c/ov5640.c: Patch [aa4bb8b] in NXP tree is now covered by patches [79ec057] and [b2f8546] from upstream. Changes from NXP patch [99aa4c8] are covered in upstream version as well. - drivers/net/ethernet/freescale/fec_main.c: Fix merge fuzz for patch [9e70485] from upstream. - drivers/usb/cdns3/gadget.c: Keep NXP version of the file, upstream version is not compatible. - drivers/usb/dwc3/core.c: - drivers/usb/dwc3/core.h: Fix merge fuzz of patch [0804505] together wth NXP patch [b30e41d] - sound/soc/fsl/fsl_sai.c: - sound/soc/fsl/fsl_sai.h: Commit [2ea70e5] in NXP tree is now covered with commit [1ad7f52] from upstream. Signed-off-by: Andrey Zhizhikin <[email protected]>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
May 14, 2021
[ Upstream commit 0f20615 ] Fix BPF_CORE_READ_BITFIELD() macro used for reading CO-RE-relocatable bitfields. Missing breaks in a switch caused 8-byte reads always. This can confuse libbpf because it does strict checks that memory load size corresponds to the original size of the field, which in this case quite often would be wrong. After fixing that, we run into another problem, which quite subtle, so worth documenting here. The issue is in Clang optimization and CO-RE relocation interactions. Without that asm volatile construct (also known as barrier_var()), Clang will re-order BYTE_OFFSET and BYTE_SIZE relocations and will apply BYTE_OFFSET 4 times for each switch case arm. This will result in the same error from libbpf about mismatch of memory load size and original field size. I.e., if we were reading u32, we'd still have *(u8 *), *(u16 *), *(u32 *), and *(u64 *) memory loads, three of which will fail. Using barrier_var() forces Clang to apply BYTE_OFFSET relocation first (and once) to calculate p, after which value of p is used without relocation in each of switch case arms, doing appropiately-sized memory load. Here's the list of relevant relocations and pieces of generated BPF code before and after this patch for test_core_reloc_bitfields_direct selftests. BEFORE ===== Freescale#45: core_reloc: insn Freescale#160 --> [5] + 0:5: byte_sz --> struct core_reloc_bitfields.u32 Freescale#46: core_reloc: insn Freescale#167 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#47: core_reloc: insn Freescale#174 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#48: core_reloc: insn Freescale#178 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#49: core_reloc: insn Freescale#182 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 157: 18 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r2 = 0 ll 159: 7b 12 20 01 00 00 00 00 *(u64 *)(r2 + 288) = r1 160: b7 02 00 00 04 00 00 00 r2 = 4 ; BYTE_SIZE relocation here ^^^ 161: 66 02 07 00 03 00 00 00 if w2 s> 3 goto +7 <LBB0_63> 162: 16 02 0d 00 01 00 00 00 if w2 == 1 goto +13 <LBB0_65> 163: 16 02 01 00 02 00 00 00 if w2 == 2 goto +1 <LBB0_66> 164: 05 00 12 00 00 00 00 00 goto +18 <LBB0_69> 0000000000000528 <LBB0_66>: 165: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 167: 69 11 08 00 00 00 00 00 r1 = *(u16 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 168: 05 00 0e 00 00 00 00 00 goto +14 <LBB0_69> 0000000000000548 <LBB0_63>: 169: 16 02 0a 00 04 00 00 00 if w2 == 4 goto +10 <LBB0_67> 170: 16 02 01 00 08 00 00 00 if w2 == 8 goto +1 <LBB0_68> 171: 05 00 0b 00 00 00 00 00 goto +11 <LBB0_69> 0000000000000560 <LBB0_68>: 172: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 174: 79 11 08 00 00 00 00 00 r1 = *(u64 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 175: 05 00 07 00 00 00 00 00 goto +7 <LBB0_69> 0000000000000580 <LBB0_65>: 176: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 178: 71 11 08 00 00 00 00 00 r1 = *(u8 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 179: 05 00 03 00 00 00 00 00 goto +3 <LBB0_69> 00000000000005a0 <LBB0_67>: 180: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 182: 61 11 08 00 00 00 00 00 r1 = *(u32 *)(r1 + 8) ; BYTE_OFFSET relo here w/ RIGHT size ^^^^^^^^^^^^^^^^ 00000000000005b8 <LBB0_69>: 183: 67 01 00 00 20 00 00 00 r1 <<= 32 184: b7 02 00 00 00 00 00 00 r2 = 0 185: 16 02 02 00 00 00 00 00 if w2 == 0 goto +2 <LBB0_71> 186: c7 01 00 00 20 00 00 00 r1 s>>= 32 187: 05 00 01 00 00 00 00 00 goto +1 <LBB0_72> 00000000000005e0 <LBB0_71>: 188: 77 01 00 00 20 00 00 00 r1 >>= 32 AFTER ===== Freescale#30: core_reloc: insn Freescale#132 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#31: core_reloc: insn Freescale#134 --> [5] + 0:5: byte_sz --> struct core_reloc_bitfields.u32 129: 18 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r2 = 0 ll 131: 7b 12 20 01 00 00 00 00 *(u64 *)(r2 + 288) = r1 132: b7 01 00 00 08 00 00 00 r1 = 8 ; BYTE_OFFSET relo here ^^^ ; no size check for non-memory dereferencing instructions 133: 0f 12 00 00 00 00 00 00 r2 += r1 134: b7 03 00 00 04 00 00 00 r3 = 4 ; BYTE_SIZE relocation here ^^^ 135: 66 03 05 00 03 00 00 00 if w3 s> 3 goto +5 <LBB0_63> 136: 16 03 09 00 01 00 00 00 if w3 == 1 goto +9 <LBB0_65> 137: 16 03 01 00 02 00 00 00 if w3 == 2 goto +1 <LBB0_66> 138: 05 00 0a 00 00 00 00 00 goto +10 <LBB0_69> 0000000000000458 <LBB0_66>: 139: 69 21 00 00 00 00 00 00 r1 = *(u16 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 140: 05 00 08 00 00 00 00 00 goto +8 <LBB0_69> 0000000000000468 <LBB0_63>: 141: 16 03 06 00 04 00 00 00 if w3 == 4 goto +6 <LBB0_67> 142: 16 03 01 00 08 00 00 00 if w3 == 8 goto +1 <LBB0_68> 143: 05 00 05 00 00 00 00 00 goto +5 <LBB0_69> 0000000000000480 <LBB0_68>: 144: 79 21 00 00 00 00 00 00 r1 = *(u64 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 145: 05 00 03 00 00 00 00 00 goto +3 <LBB0_69> 0000000000000490 <LBB0_65>: 146: 71 21 00 00 00 00 00 00 r1 = *(u8 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 147: 05 00 01 00 00 00 00 00 goto +1 <LBB0_69> 00000000000004a0 <LBB0_67>: 148: 61 21 00 00 00 00 00 00 r1 = *(u32 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 00000000000004a8 <LBB0_69>: 149: 67 01 00 00 20 00 00 00 r1 <<= 32 150: b7 02 00 00 00 00 00 00 r2 = 0 151: 16 02 02 00 00 00 00 00 if w2 == 0 goto +2 <LBB0_71> 152: c7 01 00 00 20 00 00 00 r1 s>>= 32 153: 05 00 01 00 00 00 00 00 goto +1 <LBB0_72> 00000000000004d0 <LBB0_71>: 154: 77 01 00 00 20 00 00 00 r1 >>= 323 Fixes: ee26dad ("libbpf: Add support for relocatable bitfields") Signed-off-by: Andrii Nakryiko <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Lorenz Bauer <[email protected]> Link: https://lore.kernel.org/bpf/[email protected] Signed-off-by: Sasha Levin <[email protected]>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
May 14, 2021
[ Upstream commit 0f20615 ] Fix BPF_CORE_READ_BITFIELD() macro used for reading CO-RE-relocatable bitfields. Missing breaks in a switch caused 8-byte reads always. This can confuse libbpf because it does strict checks that memory load size corresponds to the original size of the field, which in this case quite often would be wrong. After fixing that, we run into another problem, which quite subtle, so worth documenting here. The issue is in Clang optimization and CO-RE relocation interactions. Without that asm volatile construct (also known as barrier_var()), Clang will re-order BYTE_OFFSET and BYTE_SIZE relocations and will apply BYTE_OFFSET 4 times for each switch case arm. This will result in the same error from libbpf about mismatch of memory load size and original field size. I.e., if we were reading u32, we'd still have *(u8 *), *(u16 *), *(u32 *), and *(u64 *) memory loads, three of which will fail. Using barrier_var() forces Clang to apply BYTE_OFFSET relocation first (and once) to calculate p, after which value of p is used without relocation in each of switch case arms, doing appropiately-sized memory load. Here's the list of relevant relocations and pieces of generated BPF code before and after this patch for test_core_reloc_bitfields_direct selftests. BEFORE ===== Freescale#45: core_reloc: insn Freescale#160 --> [5] + 0:5: byte_sz --> struct core_reloc_bitfields.u32 Freescale#46: core_reloc: insn Freescale#167 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#47: core_reloc: insn Freescale#174 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#48: core_reloc: insn Freescale#178 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#49: core_reloc: insn Freescale#182 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 157: 18 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r2 = 0 ll 159: 7b 12 20 01 00 00 00 00 *(u64 *)(r2 + 288) = r1 160: b7 02 00 00 04 00 00 00 r2 = 4 ; BYTE_SIZE relocation here ^^^ 161: 66 02 07 00 03 00 00 00 if w2 s> 3 goto +7 <LBB0_63> 162: 16 02 0d 00 01 00 00 00 if w2 == 1 goto +13 <LBB0_65> 163: 16 02 01 00 02 00 00 00 if w2 == 2 goto +1 <LBB0_66> 164: 05 00 12 00 00 00 00 00 goto +18 <LBB0_69> 0000000000000528 <LBB0_66>: 165: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 167: 69 11 08 00 00 00 00 00 r1 = *(u16 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 168: 05 00 0e 00 00 00 00 00 goto +14 <LBB0_69> 0000000000000548 <LBB0_63>: 169: 16 02 0a 00 04 00 00 00 if w2 == 4 goto +10 <LBB0_67> 170: 16 02 01 00 08 00 00 00 if w2 == 8 goto +1 <LBB0_68> 171: 05 00 0b 00 00 00 00 00 goto +11 <LBB0_69> 0000000000000560 <LBB0_68>: 172: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 174: 79 11 08 00 00 00 00 00 r1 = *(u64 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 175: 05 00 07 00 00 00 00 00 goto +7 <LBB0_69> 0000000000000580 <LBB0_65>: 176: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 178: 71 11 08 00 00 00 00 00 r1 = *(u8 *)(r1 + 8) ; BYTE_OFFSET relo here w/ WRONG size ^^^^^^^^^^^^^^^^ 179: 05 00 03 00 00 00 00 00 goto +3 <LBB0_69> 00000000000005a0 <LBB0_67>: 180: 18 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r1 = 0 ll 182: 61 11 08 00 00 00 00 00 r1 = *(u32 *)(r1 + 8) ; BYTE_OFFSET relo here w/ RIGHT size ^^^^^^^^^^^^^^^^ 00000000000005b8 <LBB0_69>: 183: 67 01 00 00 20 00 00 00 r1 <<= 32 184: b7 02 00 00 00 00 00 00 r2 = 0 185: 16 02 02 00 00 00 00 00 if w2 == 0 goto +2 <LBB0_71> 186: c7 01 00 00 20 00 00 00 r1 s>>= 32 187: 05 00 01 00 00 00 00 00 goto +1 <LBB0_72> 00000000000005e0 <LBB0_71>: 188: 77 01 00 00 20 00 00 00 r1 >>= 32 AFTER ===== Freescale#30: core_reloc: insn Freescale#132 --> [5] + 0:5: byte_off --> struct core_reloc_bitfields.u32 Freescale#31: core_reloc: insn Freescale#134 --> [5] + 0:5: byte_sz --> struct core_reloc_bitfields.u32 129: 18 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 r2 = 0 ll 131: 7b 12 20 01 00 00 00 00 *(u64 *)(r2 + 288) = r1 132: b7 01 00 00 08 00 00 00 r1 = 8 ; BYTE_OFFSET relo here ^^^ ; no size check for non-memory dereferencing instructions 133: 0f 12 00 00 00 00 00 00 r2 += r1 134: b7 03 00 00 04 00 00 00 r3 = 4 ; BYTE_SIZE relocation here ^^^ 135: 66 03 05 00 03 00 00 00 if w3 s> 3 goto +5 <LBB0_63> 136: 16 03 09 00 01 00 00 00 if w3 == 1 goto +9 <LBB0_65> 137: 16 03 01 00 02 00 00 00 if w3 == 2 goto +1 <LBB0_66> 138: 05 00 0a 00 00 00 00 00 goto +10 <LBB0_69> 0000000000000458 <LBB0_66>: 139: 69 21 00 00 00 00 00 00 r1 = *(u16 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 140: 05 00 08 00 00 00 00 00 goto +8 <LBB0_69> 0000000000000468 <LBB0_63>: 141: 16 03 06 00 04 00 00 00 if w3 == 4 goto +6 <LBB0_67> 142: 16 03 01 00 08 00 00 00 if w3 == 8 goto +1 <LBB0_68> 143: 05 00 05 00 00 00 00 00 goto +5 <LBB0_69> 0000000000000480 <LBB0_68>: 144: 79 21 00 00 00 00 00 00 r1 = *(u64 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 145: 05 00 03 00 00 00 00 00 goto +3 <LBB0_69> 0000000000000490 <LBB0_65>: 146: 71 21 00 00 00 00 00 00 r1 = *(u8 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 147: 05 00 01 00 00 00 00 00 goto +1 <LBB0_69> 00000000000004a0 <LBB0_67>: 148: 61 21 00 00 00 00 00 00 r1 = *(u32 *)(r2 + 0) ; NO CO-RE relocation here ^^^^^^^^^^^^^^^^ 00000000000004a8 <LBB0_69>: 149: 67 01 00 00 20 00 00 00 r1 <<= 32 150: b7 02 00 00 00 00 00 00 r2 = 0 151: 16 02 02 00 00 00 00 00 if w2 == 0 goto +2 <LBB0_71> 152: c7 01 00 00 20 00 00 00 r1 s>>= 32 153: 05 00 01 00 00 00 00 00 goto +1 <LBB0_72> 00000000000004d0 <LBB0_71>: 154: 77 01 00 00 20 00 00 00 r1 >>= 323 Fixes: ee26dad ("libbpf: Add support for relocatable bitfields") Signed-off-by: Andrii Nakryiko <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Lorenz Bauer <[email protected]> Link: https://lore.kernel.org/bpf/[email protected] Signed-off-by: Sasha Levin <[email protected]>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
Nov 17, 2022
commit 1a0c016 upstream. Move am65_cpsw_nuss_phylink_cleanup() call to after am65_cpsw_nuss_cleanup_ndev() so phylink is still valid to prevent the below Segmentation fault on module remove when first slave link is up. [ 31.652944] Unable to handle kernel paging request at virtual address 00040008000005f4 [ 31.684627] Mem abort info: [ 31.687446] ESR = 0x0000000096000004 [ 31.704614] EC = 0x25: DABT (current EL), IL = 32 bits [ 31.720663] SET = 0, FnV = 0 [ 31.723729] EA = 0, S1PTW = 0 [ 31.740617] FSC = 0x04: level 0 translation fault [ 31.756624] Data abort info: [ 31.759508] ISV = 0, ISS = 0x00000004 [ 31.776705] CM = 0, WnR = 0 [ 31.779695] [00040008000005f4] address between user and kernel address ranges [ 31.808644] Internal error: Oops: 0000000096000004 [Freescale#1] PREEMPT SMP [ 31.814928] Modules linked in: wlcore_sdio wl18xx wlcore mac80211 libarc4 cfg80211 rfkill crct10dif_ce phy_gmii_sel ti_am65_cpsw_nuss(-) sch_fq_codel ipv6 [ 31.828776] CPU: 0 PID: 1026 Comm: modprobe Not tainted 6.1.0-rc2-00012-gfabfcf7dafdb-dirty Freescale#160 [ 31.837547] Hardware name: Texas Instruments AM625 (DT) [ 31.842760] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 31.849709] pc : phy_stop+0x18/0xf8 [ 31.853202] lr : phylink_stop+0x38/0xf8 [ 31.857031] sp : ffff80000a0839f0 [ 31.860335] x29: ffff80000a0839f0 x28: ffff000000de1c80 x27: 0000000000000000 [ 31.867462] x26: 0000000000000000 x25: 0000000000000000 x24: ffff80000a083b98 [ 31.874589] x23: 0000000000000800 x22: 0000000000000001 x21: ffff000001bfba90 [ 31.881715] x20: ffff0000015ee000 x19: 0004000800000200 x18: 0000000000000000 [ 31.888842] x17: ffff800076c45000 x16: ffff800008004000 x15: 000058e39660b106 [ 31.895969] x14: 0000000000000144 x13: 0000000000000144 x12: 0000000000000000 [ 31.903095] x11: 000000000000275f x10: 00000000000009e0 x9 : ffff80000a0837d0 [ 31.910222] x8 : ffff000000de26c0 x7 : ffff00007fbd6540 x6 : ffff00007fbd64c0 [ 31.917349] x5 : ffff00007fbd0b10 x4 : ffff00007fbd0b10 x3 : ffff00007fbd3920 [ 31.924476] x2 : d0a07fcff8b8d500 x1 : 0000000000000000 x0 : 0004000800000200 [ 31.931603] Call trace: [ 31.934042] phy_stop+0x18/0xf8 [ 31.937177] phylink_stop+0x38/0xf8 [ 31.940657] am65_cpsw_nuss_ndo_slave_stop+0x28/0x1e0 [ti_am65_cpsw_nuss] [ 31.947452] __dev_close_many+0xa4/0x140 [ 31.951371] dev_close_many+0x84/0x128 [ 31.955115] unregister_netdevice_many+0x130/0x6d0 [ 31.959897] unregister_netdevice_queue+0x94/0xd8 [ 31.964591] unregister_netdev+0x24/0x38 [ 31.968504] am65_cpsw_nuss_cleanup_ndev.isra.0+0x48/0x70 [ti_am65_cpsw_nuss] [ 31.975637] am65_cpsw_nuss_remove+0x58/0xf8 [ti_am65_cpsw_nuss] Cc: <[email protected]> # v5.18+ Fixes: e8609e6 ("net: ethernet: ti: am65-cpsw: Convert to PHYLINK") Signed-off-by: Roger Quadros <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Notes to upgrade, following merge conflicts were resolved:
v5.4.73:
arch/arm/boot/dts/imx6sl.dtsi:Commit [a1767c9] in NXP tree is now covered with commit [5c4c2f4] from upstream.
drivers/gpu/drm/mxsfb/mxsfb_drv.c:Resolve merge hunk for patch [ed8b90d] from upstream
drivers/media/i2c/ov5640.c:Patch [aa4bb8b] in NXP tree is now covered by patches [79ec057] and [b2f8546] from upstream. Changes from NXP patch [99aa4c8] are covered in upstream version as well.
drivers/net/ethernet/freescale/fec_main.c:Fix merge fuzz for patch [9e70485] from upstream.
drivers/usb/cdns3/gadget.c:Keep NXP version of the file, upstream version is not compatible.
drivers/usb/dwc3/core.h:drivers/usb/dwc3/core.c:Fix merge fuzz of patch [0804505] together wth NXP patch [b30e41d]
sound/soc/fsl/fsl_sai.c:sound/soc/fsl/fsl_sai.h:Commit [2ea70e5] in NXP tree is now covered with commit [1ad7f52] from upstream.
Kernel has been built for both aarch64 (
imx_v8_defconfig) and arm32 (imx_v7_defconfig).Boot-tested on imx8mpevk, result - Pass.
-- andrey