Marlin 1.0.0b1 : NOT_ATTACHED in ReplicatorG

[alx]

Hi,

Thanks for the update on Marlin v1.0.0b1.

Here is the issue I've got, using replicatorg 0025 under OSX Lion:

1. use Arduino to upload new firmware, everything goes well
2. open ReplicatorG, console seems to recognized the printer, but have an issue at the end, and display a red status noted as "NOT_ATTACHED"

[13:13:16] Load file : /Users/alx/Desktop/arduipilot 2/1.gcode
[13:13:17] /Users/alx/Desktop/arduipilot 2/1.stl
[13:13:17] Got name Default
[13:13:17] Parsed object name[Default] facets 52
[13:13:17] Could not load machine 'Ultimaker v1.0 (EXPERIMENTAL Sprinter firmware)' no machineNode found
[13:13:17] Unable to connect to machine!
[13:13:17] Please select your machine from the menu under Machine -> Driver.
[13:13:17] could not load machine 'Ultimaker v1.0 (EXPERIMENTAL Sprinter firmware)' please check Driver-> <Machine Name> 
[13:13:57] Loading simulator.
[13:13:57] Loading driver: replicatorg.drivers.reprap.RepRap5DDriver
[13:13:57] Connecting to machine using serial port: /dev/tty.usbmodemfd121
[13:13:57] Initializing Serial.
[13:13:57] Attempting to reset Ultimaker (pulsing RTS)
[13:13:57] echo:1.0.0 beta 1
[13:13:57] Supports RC
[13:13:58] echo:free memory:echo:1.0.0 beta 1
[13:13:58] echo:free memory:5371
[13:13:58] echo:using default settings:
[13:13:58] echo:steps per unit:
[13:13:58] echo:  m92 x78.74 y78.74 z533.00 e836.00
[13:13:58] echo:maximum feedrates (mm/s):
[13:13:58] echo:  m203 x8.33 y8.33 z0.08 e3333.33
[13:13:58] echo:maximum acceleration (mm/s2):
[13:13:58] echo:  m201 x9000 y9000 z100 e10000
[13:13:58] echo:acceleration: s=acceleration, t=retract acceleration
[13:13:58] echo:  m204 s3000.00 t7000.00
[13:13:58] echo:advanced variables: s=min feedrate (mm/s), t=min travel feedrate (mm/s), b=minimum segment time (ms), x=maximum xy jerk (mm/s),  z=maximum z jerk (mm/s)
[13:13:58] echo:  m205 s0.00 t0.00 b20000 x0.50 z0.01
[13:13:58] echo:pid settings:
[13:13:58] echo:   m301 p22.20 i0.12 d990.00
[13:14:01] Ultimaker not responding to gcode. Failed to connect.
[13:14:01] Supports RC

I've tried with newly release replicatorg 0026_alpha2, with the same issue.

I've change the Configuration.h in Marlin firmware to have a baudrate of 115200 instead of 250000 (how do you use 250000 baudrate replicatorg? I suppose you use Printrun?).

[ErikZalm]

Hello Alexandre,

I always use Printrun. With that I can communicate on 250000 baud.
For replicatorG 115200 is the default value. I don't know if you can switch replicatorG to 250000.

Best regards,

Erik van der Zalm

On Nov 22, 2011, at 1:19 PM, Alexandre Girard wrote:

Hi,

Thanks for the update on Marlin v1.0.0b1.

Here is the issue I've got, using replicatorg 0025 under OSX Lion:

1. use Arduino to upload new firmware, everything goes well
2. open ReplicatorG, console seems to recognized the printer, but have an issue at the end, and display a red status noted as "NOT_ATTACHED"

[13:13:16] Load file : /Users/alx/Desktop/arduipilot 2/1.gcode
[13:13:17] /Users/alx/Desktop/arduipilot 2/1.stl
[13:13:17] Got name Default
[13:13:17] Parsed object name[Default] facets 52
[13:13:17] Could not load machine 'Ultimaker v1.0 (EXPERIMENTAL Sprinter firmware)' no machineNode found
[13:13:17] Unable to connect to machine!
[13:13:17] Please select your machine from the menu under Machine -> Driver.
[13:13:17] could not load machine 'Ultimaker v1.0 (EXPERIMENTAL Sprinter firmware)' please check Driver-> <Machine Name> 
[13:13:57] Loading simulator.
[13:13:57] Loading driver: replicatorg.drivers.reprap.RepRap5DDriver
[13:13:57] Connecting to machine using serial port: /dev/tty.usbmodemfd121
[13:13:57] Initializing Serial.
[13:13:57] Attempting to reset Ultimaker (pulsing RTS)
[13:13:57] echo:1.0.0 beta 1
[13:13:57] Supports RC
[13:13:58] echo:free memory:echo:1.0.0 beta 1
[13:13:58] echo:free memory:5371
[13:13:58] echo:using default settings:
[13:13:58] echo:steps per unit:
[13:13:58] echo:  m92 x78.74 y78.74 z533.00 e836.00
[13:13:58] echo:maximum feedrates (mm/s):
[13:13:58] echo:  m203 x8.33 y8.33 z0.08 e3333.33
[13:13:58] echo:maximum acceleration (mm/s2):
[13:13:58] echo:  m201 x9000 y9000 z100 e10000
[13:13:58] echo:acceleration: s=acceleration, t=retract acceleration
[13:13:58] echo:  m204 s3000.00 t7000.00
[13:13:58] echo:advanced variables: s=min feedrate (mm/s), t=min travel feedrate (mm/s), b=minimum segment time (ms), x=maximum xy jerk (mm/s),  z=maximum z jerk (mm/s)
[13:13:58] echo:  m205 s0.00 t0.00 b20000 x0.50 z0.01
[13:13:58] echo:pid settings:
[13:13:58] echo:   m301 p22.20 i0.12 d990.00
[13:14:01] Ultimaker not responding to gcode. Failed to connect.
[13:14:01] Supports RC

I've tried with newly release replicatorg 0026_alpha2, with the same issue.

I've change the Configuration.h in Marlin firmware to have a baudrate of 115200 instead of 250000 (how do you use 250000 baudrate replicatorg? I suppose you use Printrun?).

---

Reply to this email directly or view it on GitHub:
https://github.com/ErikZalm/Marlin/issues/15

[bkubicek]

Erik, i think the baud rate is not the problem here, because he gets echo:blabla from the printer. With baud-rate problems, most likely he would get nothing or just random data.
IIRC there is a timeout defined in the machinefile xml of repg. Maybe the machine answers to slowly, due to the bootloader or maybe sd suport? If so, try disabeling it, or try to disable the eeprom support.

[alx]

Yes, the baudrate was already changed in configuration.h in order to be able to get printer serial in replicatorg.

Thanks for the tips, I'll try to change the timeout and/or eeprom support to see if it changes something.

[bkubicek]

alx: and, any progress?

[alx]

Not really, I'm moving to printrun and learn more about skeingforge/sfact settings.

Hope someone else will be able to get this version working on ReplicatorG, most people in our hackerspace will still use it.

[lalalandrus]

I found the issue, this issue is also exhibited with repetier-host and repsnapper.

When issuing gcode M115, the serial print doesnt print a new line after extruder count. This causes the "ok" to look like it is part of extruder count. The "ok" is not parsed and the host software doesnt know what to do. Solution is to add a "\n" after extruder count as a space is insufficient.

[bkubicek]

can you try, i just pushed a commit.
Bernhard

On Sun, Jan 15, 2012 at 8:37 PM, lalalandrus <
[email protected]

wrote:

I found the issue, this issue is also exhibited with repetier-host and
repsnapper.

When issuing gcode M115, the serial print doesnt print a new line after
extruder count. This causes the "ok" to look like it is part of extruder
count. The "ok" is not parsed and the host software doesnt know what to do.
Solution is to add a "\n" after extruder count as a space is insufficient.

---

Reply to this email directly or view it on GitHub:
https://github.com/ErikZalm/Marlin/issues/15#issuecomment-3501191

[lalalandrus]

looks good on my end, repG, repsnapper and repetier-host all confirmed working

[github-actions]

This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs.