Replace PLA/ABS preheating with generic

Marlin/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/Marlin_main.cpp

@@ -4908,32 +4908,32 @@ inline void gcode_M140() {
         case 0:
           if (code_seen('H')) {
             v = code_value_int();
-            plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            preheatHotendTemp1 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
           }
           if (code_seen('F')) {
             v = code_value_int();
-            plaPreheatFanSpeed = constrain(v, 0, 255);
+            preheatFanSpeed1 = constrain(v, 0, 255);
           }
           #if TEMP_SENSOR_BED != 0
             if (code_seen('B')) {
               v = code_value_int();
-              plaPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
+              preheatBedTemp1 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
             }
           #endif
           break;
         case 1:
           if (code_seen('H')) {
             v = code_value_int();
-            absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
+            preheatHotendTemp2 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
           }
           if (code_seen('F')) {
             v = code_value_int();
-            absPreheatFanSpeed = constrain(v, 0, 255);
+            preheatFanSpeed2 = constrain(v, 0, 255);
           }
           #if TEMP_SENSOR_BED != 0
             if (code_seen('B')) {
               v = code_value_int();
-              absPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
+              preheatBedTemp2 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
             }
           #endif
           break;

Marlin/SanityCheck.h

@@ -644,6 +644,18 @@
   #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
 #elif ENABLED(FILAMENTCHANGEENABLE)
   #error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
+#elif defined(PLA_PREHEAT_HOTEND_TEMP)
+  #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
+#elif defined(PLA_PREHEAT_HPB_TEMP)
+  #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
+#elif defined(PLA_PREHEAT_FAN_SPEED)
+  #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
+#elif defined(ABS_PREHEAT_HOTEND_TEMP)
+  #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
+#elif defined(ABS_PREHEAT_HPB_TEMP)
+  #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
+#elif defined(ABS_PREHEAT_FAN_SPEED)
+  #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
 #endif
 
 #endif //SANITYCHECK_H

Marlin/configuration_store.cpp

@@ -85,12 +85,12 @@
  *  285  M666 Z    z_endstop_adj (float)
  *
  * ULTIPANEL:
- *  289  M145 S0 H plaPreheatHotendTemp (int)
- *  291  M145 S0 B plaPreheatHPBTemp (int)
- *  293  M145 S0 F plaPreheatFanSpeed (int)
- *  295  M145 S1 H absPreheatHotendTemp (int)
- *  297  M145 S1 B absPreheatHPBTemp (int)
- *  299  M145 S1 F absPreheatFanSpeed (int)
+ *  289  M145 S0 H preheatHotendTemp1 (int)
+ *  291  M145 S0 B preheatBedTemp1 (int)
+ *  293  M145 S0 F preheatFanSpeed1 (int)
+ *  295  M145 S1 H preheatHotendTemp2 (int)
+ *  297  M145 S1 B preheatBedTemp2 (int)
+ *  299  M145 S1 F preheatFanSpeed2 (int)
  *
  * PIDTEMP:
  *  301  M301 E0 PIDC  Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
@@ -262,16 +262,16 @@ void Config_StoreSettings()  {
   #endif
 
   #if DISABLED(ULTIPANEL)
-    int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
-        absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
+    int preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND, preheatBedTemp1 = PREHEAT_1_TEMP_BED, preheatFanSpeed1 = PREHEAT_1_FAN_SPEED,
+        preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND, preheatBedTemp2 = PREHEAT_2_TEMP_BED, preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
   #endif // !ULTIPANEL
 
-  EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
-  EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
-  EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
-  EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
-  EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
-  EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
+  EEPROM_WRITE_VAR(i, preheatHotendTemp1);
+  EEPROM_WRITE_VAR(i, preheatBedTemp1);
+  EEPROM_WRITE_VAR(i, preheatFanSpeed1);
+  EEPROM_WRITE_VAR(i, preheatHotendTemp2);
+  EEPROM_WRITE_VAR(i, preheatBedTemp2);
+  EEPROM_WRITE_VAR(i, preheatFanSpeed2);
 
   for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
 
@@ -447,16 +447,16 @@ void Config_RetrieveSettings() {
     #endif
 
     #if DISABLED(ULTIPANEL)
-      int plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed,
-          absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed;
+      int preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1,
+          preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2;
     #endif
 
-    EEPROM_READ_VAR(i, plaPreheatHotendTemp);
-    EEPROM_READ_VAR(i, plaPreheatHPBTemp);
-    EEPROM_READ_VAR(i, plaPreheatFanSpeed);
-    EEPROM_READ_VAR(i, absPreheatHotendTemp);
-    EEPROM_READ_VAR(i, absPreheatHPBTemp);
-    EEPROM_READ_VAR(i, absPreheatFanSpeed);
+    EEPROM_READ_VAR(i, preheatHotendTemp1);
+    EEPROM_READ_VAR(i, preheatBedTemp1);
+    EEPROM_READ_VAR(i, preheatFanSpeed1);
+    EEPROM_READ_VAR(i, preheatHotendTemp2);
+    EEPROM_READ_VAR(i, preheatBedTemp2);
+    EEPROM_READ_VAR(i, preheatFanSpeed2);
 
     #if ENABLED(PIDTEMP)
       for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
@@ -604,12 +604,12 @@ void Config_ResetDefault() {
   #endif
 
   #if ENABLED(ULTIPANEL)
-    plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP;
-    plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP;
-    plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
-    absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP;
-    absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP;
-    absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
+    preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND;
+    preheatBedTemp1 = PREHEAT_1_TEMP_BED;
+    preheatFanSpeed1 = PREHEAT_1_FAN_SPEED;
+    preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND;
+    preheatBedTemp2 = PREHEAT_2_TEMP_BED;
+    preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
   #endif
 
   #if HAS_LCD_CONTRAST
@@ -814,14 +814,14 @@ void Config_PrintSettings(bool forReplay) {
       SERIAL_ECHOLNPGM("Material heatup parameters:");
       CONFIG_ECHO_START;
     }
-    SERIAL_ECHOPAIR("  M145 S0 H", plaPreheatHotendTemp);
-    SERIAL_ECHOPAIR(" B", plaPreheatHPBTemp);
-    SERIAL_ECHOPAIR(" F", plaPreheatFanSpeed);
+    SERIAL_ECHOPAIR("  M145 S0 H", preheatHotendTemp1);
+    SERIAL_ECHOPAIR(" B", preheatBedTemp1);
+    SERIAL_ECHOPAIR(" F", preheatFanSpeed1);
     SERIAL_EOL;
     CONFIG_ECHO_START;
-    SERIAL_ECHOPAIR("  M145 S1 H", absPreheatHotendTemp);
-    SERIAL_ECHOPAIR(" B", absPreheatHPBTemp);
-    SERIAL_ECHOPAIR(" F", absPreheatFanSpeed);
+    SERIAL_ECHOPAIR("  M145 S1 H", preheatHotendTemp2);
+    SERIAL_ECHOPAIR(" B", preheatBedTemp2);
+    SERIAL_ECHOPAIR(" F", preheatFanSpeed2);
     SERIAL_EOL;
   #endif // ULTIPANEL
 

Marlin/example_configurations/Cartesio/Configuration.h

@@ -777,13 +777,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 190
-#define PLA_PREHEAT_HPB_TEMP 50
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 190
+#define PREHEAT_1_TEMP_BED     50
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Felix/Configuration.h

@@ -761,13 +761,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -759,13 +759,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Hephestos/Configuration.h

@@ -770,13 +770,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 200
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 200
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 220
-#define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 220
+#define PREHEAT_2_TEMP_BED    100
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -772,13 +772,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP    70
-#define PLA_PREHEAT_FAN_SPEED   0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP    110
-#define ABS_PREHEAT_FAN_SPEED   0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8200/Configuration.h

@@ -795,13 +795,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 190
-#define PLA_PREHEAT_HPB_TEMP 50 // K8200: set back to 70 if you have an upgraded heatbed power supply
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 190
+#define PREHEAT_1_TEMP_BED     50 // K8200: set back to 70 if you have an upgraded heatbed power supply
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 60 // K8200: set back to 110 if you have an upgraded heatbed power supply
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     60 // K8200: set back to 110 if you have an upgraded heatbed power supply
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8400/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   165 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 245
-#define ABS_PREHEAT_HPB_TEMP 0
-#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 245
+#define PREHEAT_2_TEMP_BED      0
+#define PREHEAT_2_FAN_SPEED   165 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/K8400/Dual Heads/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 0
-#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 210
+#define PREHEAT_1_TEMP_BED      0
+#define PREHEAT_1_FAN_SPEED   165 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 245
-#define ABS_PREHEAT_HPB_TEMP 0
-#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 245
+#define PREHEAT_2_TEMP_BED      0
+#define PREHEAT_2_FAN_SPEED   165 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 0   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 //
 // Print job timer

Marlin/example_configurations/RigidBot/Configuration.h

@@ -776,13 +776,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // @section temperature
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180
-#define PLA_PREHEAT_HPB_TEMP 70
-#define PLA_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
-#define ABS_PREHEAT_HOTEND_TEMP 240
-#define ABS_PREHEAT_HPB_TEMP 110
-#define ABS_PREHEAT_FAN_SPEED 255   // Insert Value between 0 and 255
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
 
 //
 // Print job timer