Config for the Open_Core0

.github/workflows/cmake.yml

@@ -23,7 +23,7 @@ jobs:
     runs-on: ubuntu-latest
     strategy:
       matrix:
-        GP2040_BOARDCONFIG: [Pico, PicoW, AlpacaOwO, BentoBox, DURAL, FightboardV3, FightboardV3Mirrored, FlatboxRev4, FlatboxRev5, FlatboxRev5RGB, FlatboxRev5Southpaw, KB2040, KeyboardConverter, Liatris, MavercadeKeebfighter, OpenCore0WASD, PicoAnn, PicoFightingBoard, ReflexCtrlSNES, ReflexEncoder, RP2040AdvancedBreakoutBoard, RP2040AdvancedBreakoutBoardUSBPassthrough, RP2040MiniBreakoutBoard, SparkFunProMicro, WaveshareZero, Stress, SGFDevices  ]
+        GP2040_BOARDCONFIG: [Pico, PicoW, AlpacaOwO, BentoBox, DURAL, FightboardV3, FightboardV3Mirrored, FlatboxRev4, FlatboxRev5, FlatboxRev5RGB, FlatboxRev5Southpaw, KB2040, KeyboardConverter, Liatris, MavercadeKeebfighter, OpenCore0, OpenCore0WASD, PicoAnn, PicoFightingBoard, ReflexCtrlSNES, ReflexEncoder, RP2040AdvancedBreakoutBoard, RP2040AdvancedBreakoutBoardUSBPassthrough, RP2040MiniBreakoutBoard, SparkFunProMicro, WaveshareZero, Stress, SGFDevices  ]
 
     steps:
     #Global Setup

configs/OpenCore0/BoardConfig.h

@@ -0,0 +1,277 @@
+/*
+ * SPDX-License-Identifier: MIT
+ * SPDX-FileCopyrightText: Copyright (c) 2021 Jason Skuby (mytechtoybox.com)
+ */
+
+#ifndef PICO_BOARD_CONFIG_H_
+#define PICO_BOARD_CONFIG_H_
+
+#include "enums.pb.h"
+
+#define BOARD_CONFIG_LABEL "Open_Core0"
+
+// This is the main pin definition section.
+// This will let you specify which GPIO pin each button is assigned too.
+// You can set any of the main pins as `-1` to disable it.
+// The Turbo pin and LS + RS slider pins can also be set to `-1` to disable that functionality.
+// Please note that only when `PIN_BUTTON_TURBO` is set to `-1` will the `T##` be removed from a connected display.
+// Please note that only when `PIN_SLIDER_ONE` and  `PIN_SLIDER_TWO` are set to `-1` will the button combo shortcut for DP/LS/RS work.
+// The buttons are listed in GP2040 configuration, beside each the listed order is *GP2040 / Xinput / Switch / PS3 / Directinput / Arcade*
+
+#define PIN_DPAD_UP          12           // UP
+#define PIN_DPAD_DOWN        10           // DOWN
+#define PIN_DPAD_RIGHT       11           // RIGHT
+#define PIN_DPAD_LEFT        9            // LEFT
+#define PIN_BUTTON_B1        13           // B1 / A / B / Cross / 2 / K1
+#define PIN_BUTTON_B2        14           // B2 / B / A / Circle / 3 / K2
+#define PIN_BUTTON_R2        15           // R2 / RT / ZR / R2 / 8 / K3
+#define PIN_BUTTON_L2        16           // L2 / LT / ZL / L2 / 7 / K4
+#define PIN_BUTTON_B3        17           // B3 / X / Y / Square / 1 / P1
+#define PIN_BUTTON_B4        18           // B4 / Y / X / Triangle / 4 / P2
+#define PIN_BUTTON_R1        19           // R1 / RB / R / R1 / 6 / P3
+#define PIN_BUTTON_L1        20           // L1 / LB / L / L1 / 5 / P4
+#define PIN_BUTTON_S1        6            // S1 / Back / Minus / Select / 9 / Coin
+#define PIN_BUTTON_S2        7            // S2 / Start / Plus / Start / 10 / Start
+#define PIN_BUTTON_L3        3            // L3 / LS / LS / L3 / 11 / LS
+#define PIN_BUTTON_R3        2            // R3 / RS / RS / R3 / 12 / RS
+#define PIN_BUTTON_A1        5            // A1 / Guide / Home / PS / 13 / ~
+#define PIN_BUTTON_A2        4            // A2 / ~ / Capture / ~ / 14 / ~
+#define PIN_BUTTON_FN        -1           // Hotkey Function
+#define PIN_BUTTON_TURBO     27           // Turbo
+#define PIN_BUTTON_REVERSE   -1           // UDLR Reverse
+#define PIN_SLIDER_ONE       25           // Left Stick Slider
+#define PIN_SLIDER_TWO       24           // Right Stick Slider
+#define PIN_SLIDER_SOCD_ONE  23           // SOCD Slider Pin One
+#define PIN_SLIDER_SOCD_TWO  22           // SOCD Slider Pin Two
+
+#define TURBO_ENABLED 1
+#define JSLIDER_ENABLED 1
+
+// This is the SOCD section.
+// SOCD stands for `simultaneous opposing cardinal directions`.
+// There are three options for `DEFAULT_SOCD_MODE` currently:
+// 1 - `SOCD_MODE_NEUTRAL` - This is a neutral SOCD.  EG. when you press `up` + `down` no input will be registered.
+// 2 - `SOCD_MODE_UP_PRIORITY` - This is up priority SOCD.  EG. when you press `up` + `down` `up` will be registered.
+// 3 - `SOCD_MODE_SECOND_INPUT_PRIORITY` - This is last priority SOCD.  EG. when you press and hold `up` then press `down` `down` will be registered.
+// 4 - `SOCD_MODE_FIRST_INPUT_PRIORITY` - This is first priority SOCD.  EG. when you press and hold `up` then press `down` `up` will be registered.
+
+#define DEFAULT_SOCD_MODE SOCD_MODE_NEUTRAL
+// SOCD Slider Slot Defaults
+#define SLIDER_SOCD_ENABLED 1
+#define SLIDER_SOCD_SLOT_ONE SOCD_MODE_UP_PRIORITY
+#define SLIDER_SOCD_SLOT_TWO  SOCD_MODE_SECOND_INPUT_PRIORITY
+#define SLIDER_SOCD_SLOT_DEFAULT SOCD_MODE_NEUTRAL
+
+#define DEFAULT_FORCED_SETUP_MODE FORCED_SETUP_MODE_OFF // 	FORCED_SETUP_MODE_OFF, FORCED_SETUP_MODE_LOCK_MODE_SWITCH, FORCED_SETUP_MODE_LOCK_WEB_CONFIG, FORCED_SETUP_MODE_LOCK_BOTH
+#define DEFAULT_LOCK_HOTKEYS false // or true
+
+#define DEFAULT_PS4CONTROLLER_TYPE PS4_ARCADESTICK
+
+// This is the LEDs section.
+// The default `TURBO_LED_PIN` pin is set to `15` ( it is recommended to run through 3V3(OUT) with a resistor)
+// The Turbo LED will flash at a speed consistant with the set speed of the Turbo when a Turbo button is active.
+// It is recommended to disable the `TURBO_LED_PIN` by setting it to `-1` if you are sensitive of flashing lights.
+// The default `BOARD_LEDS_PIN` pin is set to `28`.
+// The board LED pin will allow you to connect addressible RGB LEDs on the Pico.
+// Addressible RGB LEDs should be connected to the `VBUS` pin (#40), an avalible ground pin and the defined `BOARD_LEDS_PIN`.
+// Special note - You should only ever use addressible RGB LEDs that are rated for 5v operation on the Pico.
+// The defualt `LED_BRIGHTNESS_MAXIMUM` value is `50`.
+// This will change how bright the LEDs are with `0` being off and `100` being full brightness.
+// The minimum `LED_BRIGHTNESS_MAXIMUM` value is `0`.
+// The maximum `LED_BRIGHTNESS_MAXIMUM` value is `100`.
+// The defualt `LED_BRIGHTNESS_STEPS` value is `5`.
+// This will change how many brightness steps there are when increasing or decreasing the brightness of the LEDs via the onboard shortcut.
+// It is recommend to keep this value at `5` or `10`.
+// The defualt `LED_FORMAT` is `LED_FORMAT_GRB`.
+// You can also choose the `LED_FORMAT` of `LED_FORMAT_RGB` if your addressible RGB LEDs are not working as intended.
+// The defualt `LEDS_PER_PIXEL` is set to `1`.
+// This will change how many addressible RGB LEDs there are per button.
+// The default LEDS_[BUTTON] is an order and has nothing to do with what GPIO pin something is connected to.
+// Unless you are planning on running custom animations I would recommmend you leave this as is.
+
+#define TURBO_LED_PIN -1
+
+#define BOARD_LEDS_PIN 8
+
+#define LED_BRIGHTNESS_MAXIMUM 50
+#define LED_BRIGHTNESS_STEPS 5
+#define LED_FORMAT LED_FORMAT_GRB
+#define LEDS_PER_PIXEL 2
+
+#define LEDS_DPAD_LEFT   0
+#define LEDS_DPAD_DOWN   1
+#define LEDS_DPAD_RIGHT  2
+#define LEDS_BUTTON_B3   3
+#define LEDS_BUTTON_B4   4
+#define LEDS_BUTTON_R1   5
+#define LEDS_BUTTON_L1   6
+#define LEDS_BUTTON_L2   7
+#define LEDS_BUTTON_R2   8
+#define LEDS_BUTTON_B2   9
+#define LEDS_BUTTON_B1   10
+#define LEDS_DPAD_UP     11
+
+
+// This is the Player LED section.
+// In this section you can specify if Player LEDs will be active, and, if active, which pins will be used for them.
+// The defualt is `PLED_TYPE_NONE` which will turn the Player LEDs off.
+// The default pin for each Player LED is `-1` which disables it.
+// To enable a `PLED#_PIN`, replace the `-1` with the GPIO pin number that is desired.
+// There are three options for `PLED_TYPE` currently:
+// 1 - `PLED_TYPE_NONE` - This will disable the Player LEDs
+// 2 - `PLED_TYPE_PWM` - This will enable the Player LEDs ( it is recommended to run through 3V3(OUT) with a resistor)
+// 3 - `PLED_TYPE_RGB` - This will enable the Player LEDs as addressible RGB LEDs (please not that this has not been implemented yet)
+
+#define PLED_TYPE PLED_TYPE_RGB
+#define PLED1_PIN 24
+#define PLED2_PIN 25
+#define PLED3_PIN 26
+#define PLED4_PIN 27
+
+#define PLED_COLOR ColorGreen
+
+
+// This is the Analog section.
+// In this section you can specify if Analog is enabled, and, if endabled, which pins will be used for it.
+// The default for `ANALOG_ADC_VRX` and `ANALOG_ADC_VRY` is `-1` which disables them.
+// To enable a `ANALOG_ADC_VRX` and `ANALOG_ADC_VRY`, replace the `-1` with the GPIO pin numbers that are desired.
+
+#define ANALOG_ADC_1_VRX -1
+#define ANALOG_ADC_1_VRY -1
+#define ANALOG_ADC_1_MODE DPAD_MODE_LEFT_ANALOG
+#define ANALOG_ADC_1_INVERT INVERT_NONE
+
+#define ANALOG_ADC_2_VRX -1
+#define ANALOG_ADC_2_VRY -1
+#define ANALOG_ADC_2_MODE DPAD_MODE_RIGHT_ANALOG
+#define ANALOG_ADC_2_INVERT INVERT_NONE
+
+// Reverse Button section
+#define REVERSE_LED_PIN -1
+
+// This is the I2C Display section (commonly known as the OLED display section).
+// In this section you can specify if a display as been enabled, which pins are assined to it, the block address and speed.
+// The default for `HAS_I2C_DISPLAY` is `1` which enables it.
+// To disable the display you can change `HAS_I2C_DISPLAY` to `-1`.
+// The default `I2C_SDA_PIN` is `0`.
+// The defualt `I2C_SCL_PIN` is `1`.
+// The defualt `I2C_BLOCK` is `12c0`.
+// If you change the `I2C_SDA_PIN` and `I2C_SCL_PIN` pin mapping, you may need to change the `I2C_BLOCK` as well.
+// The defualt `I2C_SPEED` is `400000`.
+// This should be more than fast enough for most displays.
+// Some smaller displays (like 0.96" and 1.31") can go up to `800000` or even `1000000`.
+// The default `DISPLAY_FLIP` is `0`.
+// This can be changed to `1` to have the dispaly output flipped.
+// The default `DISPLAY_INVERY` is `0`.
+// This can be changed to `1` to have the color on the display inverted.
+// The default `BUTTON_LAYOUT` is `BUTTON_LAYOUT_STICK` which will show an arcade stick on the left hand side of the display.
+// There are seven options for `BUTTON_LAYOUT` currently:
+// 1 - BUTTON_LAYOUT_STICK - This is a basic joystick layout
+// 2 - BUTTON_LAYOUT_STICKLESS - This is a basic stickless (all button) layout
+// 3 - BUTTON_LAYOUT_BUTTONS_ANGLED - This a WASD button layout that is angled
+// 4 - BUTTON_LAYOUT_BUTTONS_BASIC - This a WASD button layout that is straight
+// 5 - BUTTON_LAYOUT_KEYBOARD_ANGLED - This is a WASD keyboard layout that is angled
+// 6 - BUTTON_LAYOUT_KEYBOARDA - This is a WASD keyboard layout that is straight
+// 7 - BUTTON_LAYOUT_DANCEPADA - This is a dance pad layout (must be used with `BUTTON_LAYOUT_DANCEPADB` in `BUTTON_LAYOUT_RIGHT`)
+// The default `BUTTON_LAYOUT_RIGHT` is `BUTTON_LAYOUT_NOIR8` which will show eight buttons on the right hand side of the display.
+// There are eleven options for `BUTTON_LAYOUT_RIGHT` currently:
+// 1 - BUTTON_LAYOUT_ARCADE - This is a standard 8 button arcade layout
+// 2 - BUTTON_LAYOUT_STICKLESSB - This is a basic stickless (all button) layout
+// 3 - BUTTON_LAYOUT_BUTTONS_ANGLEDB - This is a standard 8 button arcade layout that is angled
+// 4 - BUTTON_LAYOUT_VEWLIX - This is the standard 8 button Vewlix layout
+// 5 - BUTTON_LAYOUT_VEWLIX7 - This is the standard 7 button Vewlix layout
+// 6 - BUTTON_LAYOUT_CAPCOM - This is the standard 8 button Capcom layout
+// 7 - BUTTON_LAYOUT_CAPCOM6 - This is the stndard 6 button Capcom layout
+// 8 - BUTTON_LAYOUT_SEGA2P - This is the standard 8 button Sega2P layout
+// 9 - BUTTON_LAYOUT_NOIR8 - This is the standard 8 button Noir layout
+// 10 - BUTTON_LAYOUT_KEYBOARDB - This is a WASD keyboard layout that is straight
+// 11 - BUTTON_LAYOUT_DANCEPADB - This is a dance pad layout (must be used with `BUTTON_LAYOUT_DANCEPADA` in `BUTTON_LAYOUT`)
+// The default `SPLASH_MODE` is `NOSPLASH`.
+// There are four options for `SPLASH_MODE` currently:
+// 1 - `STATICSPLASH` - This will display the static splash image
+// 2 - `CLOSEIN` - This will display the static splash image as a top and bottom coming together animation
+// 3 - `CLOSEINCUSTOM` - This will display the custom splash image as a top and bottom coming together animation
+// 4 - `NOSPLASH` - This will not display a splash screen on boot
+// Special note - All of the splash screen images can be changed via `include/bitmaps.h`
+
+#define HAS_I2C_DISPLAY 1
+#define I2C_SDA_PIN 0
+#define I2C_SCL_PIN 1
+#define I2C_BLOCK i2c0
+#define I2C_SPEED 400000
+#define DISPLAY_FLIP 3
+#define DISPLAY_INVERT 0
+
+#define REVERSE_UP_DEFAULT 1
+#define REVERSE_DOWN_DEFAULT 1
+#define REVERSE_LEFT_DEFAULT 1
+#define REVERSE_RIGHT_DEFAULT 1
+
+#define BUTTON_LAYOUT BUTTON_LAYOUT_STICKLESS
+#define BUTTON_LAYOUT_RIGHT BUTTON_LAYOUT_STICKLESSB
+#define SPLASH_MODE SPLASH_MODE_STATIC
+#define SPLASH_CHOICE SPLASH_CHOICE_MAIN
+#define SPLASH_DURATION 7500 // Duration in milliseconds
+
+// Board LED Add-on Setting
+// BOARD_LED_OFF  - Turns the on-board LED off
+// MODE_INDICATOR - On-board LED blinks on various frequencies depending
+//                  on the current mode (config, normal, or no USB data)
+// INPUT_TEST     - Blinks whenever any input is made
+
+#define BOARD_LED_TYPE ON_BOARD_LED_MODE_OFF
+#define BOARD_LED_PIN -1
+
+// Dual Directional Add-on Options
+
+#define PIN_DUAL_DIRECTIONAL_UP -1
+#define PIN_DUAL_DIRECTIONAL_DOWN -1
+#define PIN_DUAL_DIRECTIONAL_LEFT -1
+#define PIN_DUAL_DIRECTIONAL_RIGHT -1
+#define DUAL_DIRECTIONAL_STICK_MODE DPAD_MODE_DIGITAL
+#define DUAL_DIRECTIONAL_COMBINE_MODE DUAL_COMBINE_MODE_MIXED
+
+// BOOTSEL Button Add-on setting
+#define BOOTSEL_BUTTON_MASK 0 // 0 means none, get other mask from GamepadState.h
+
+// Extra Button Add-on setting
+#define EXTRA_BUTTON_MASK 0 // 0 means none, get other mask from GamepadState.h
+                            // For directions, use GAMEPAD_MASK_DU, GAMEPAD_MASK_DD, GAMEPAD_MASK_DL and GAMEPAD_MASK_DR
+#define EXTRA_BUTTON_PIN -1
+
+// Button Lock Add-on setting
+#define FOCUS_MODE_ENABLED 1
+#define FOCUS_MODE_BUTTON_MASK GAMEPAD_MASK_S1 | GAMEPAD_MASK_S2 | GAMEPAD_MASK_A1 | GAMEPAD_MASK_A2 | GAMEPAD_MASK_L3 | GAMEPAD_MASK_R3 // 0 means none, get other mask from GamepadState.h
+                            // For directions, use GAMEPAD_MASK_DU, GAMEPAD_MASK_DD, GAMEPAD_MASK_DL and GAMEPAD_MASK_DR
+#define FOCUS_MODE_PIN 21
+#define FOCUS_MODE_OLED_LOCK_ENABLED 0
+#define FOCUS_MODE_RGB_LOCK_ENABLED 0
+#define FOCUS_MODE_BUTTON_LOCK_ENABLED 1
+
+// USB Passthrough settings
+#define PSPASSTHROUGH_ENABLED 1
+#define PSPASSTHROUGH_PIN_DPLUS 28
+
+// Keyboard Mapping Configuration
+// List of HID keycodes can be located here: https://github.com/hathach/tinyusb/blob/3623ba1884ddff23e9b64766cb6dd032f1425846/src/class/hid/hid.h#L356
+// Even for the modifier keys, HID_KEY entries should be used as the implementation expects those and will convert as necessary.
+#define KEY_DPAD_UP     HID_KEY_ARROW_UP      // UP
+#define KEY_DPAD_DOWN   HID_KEY_ARROW_DOWN    // DOWN
+#define KEY_DPAD_RIGHT  HID_KEY_ARROW_RIGHT   // RIGHT
+#define KEY_DPAD_LEFT   HID_KEY_ARROW_LEFT    // LEFT
+#define KEY_BUTTON_B1   HID_KEY_SHIFT_LEFT    // B1 / A / B / Cross / 2 / K1
+#define KEY_BUTTON_B2   HID_KEY_Z             // B2 / B / A / Circle / 3 / K2
+#define KEY_BUTTON_R2   HID_KEY_X             // R2 / RT / ZR / R2 / 8 / K3
+#define KEY_BUTTON_L2   HID_KEY_V             // L2 / LT / ZL / L2 / 7 / K4
+#define KEY_BUTTON_B3   HID_KEY_CONTROL_LEFT  // B3 / X / Y / Square / 1 / P1
+#define KEY_BUTTON_B4   HID_KEY_ALT_LEFT      // B4 / Y / X / Triangle / 4 / P2
+#define KEY_BUTTON_R1   HID_KEY_SPACE         // R1 / RB / R / R1 / 6 / P3
+#define KEY_BUTTON_L1   HID_KEY_C             // L1 / LB / L / L1 / 5 / P4
+#define KEY_BUTTON_S1   HID_KEY_5             // S1 / Back / Minus / Select / 9 / Coin
+#define KEY_BUTTON_S2   HID_KEY_1             // S2 / Start / Plus / Start / 10 / Start
+#define KEY_BUTTON_L3   HID_KEY_EQUAL         // L3 / LS / LS / L3 / 11 / LS
+#define KEY_BUTTON_R3   HID_KEY_MINUS         // R3 / RS / RS / R3 / 12 / RS
+#define KEY_BUTTON_A1   HID_KEY_9             // A1 / Guide / Home / PS / 13 / ~
+#define KEY_BUTTON_A2   HID_KEY_F2            // A2 / ~ / Capture / ~ / 14 / ~
+
+#endif

configs/OpenCore0/Open_Core0.h

@@ -0,0 +1,48 @@
+/*
+ * Copyright (c) 2020 Raspberry Pi (Trading) Ltd.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+// -----------------------------------------------------
+// NOTE: THIS HEADER IS ALSO INCLUDED BY ASSEMBLER SO
+//       SHOULD ONLY CONSIST OF PREPROCESSOR DIRECTIVES
+// -----------------------------------------------------
+
+
+#ifndef _BOARDS_OPENCORE0_H
+#define _BOARDS_OPENCORE0_H
+
+// For board detection
+#define OPENCORE0WASD
+
+//For crappy crystal
+#ifndef PICO_XOSC_STARTUP_DELAY_MULTIPLIER
+#define PICO_XOSC_STARTUP_DELAY_MULTIPLIER 64
+#endif
+
+// --- LED ---
+#ifndef PICO_DEFAULT_LED_PIN
+#define PICO_DEFAULT_LED_PIN 25
+#endif
+// no PICO_DEFAULT_WS2812_PIN
+
+// --- FLASH ---
+#define PICO_BOOT_STAGE2_CHOOSE_W25Q080 1
+
+#ifndef PICO_FLASH_SPI_CLKDIV
+#define PICO_FLASH_SPI_CLKDIV 2
+#endif
+
+#ifndef PICO_FLASH_SIZE_BYTES
+#define PICO_FLASH_SIZE_BYTES (2 * 1024 * 1024)
+#endif
+
+// Drive high to force power supply into PWM mode (lower ripple on 3V3 at light loads)
+#define PICO_SMPS_MODE_PIN 23
+
+#ifndef PICO_RP2040_B0_SUPPORTED
+#define PICO_RP2040_B0_SUPPORTED 1
+#endif
+
+#endif

configs/OpenCore0/README.md

@@ -0,0 +1,9 @@
+# GP2040 Configuration for the Open_Core0
+
+![Open_Core0](assets/Open_Core0.jpg)
+
+Basic pin setup for the Open_Core0.
+
+![Pin Mapping](assets/Open_Core0_pinout.png)
+
+You can find the full Open_Core0 project over on our hardware section [HERE](https://github.com/OpenStickCommunity/Hardware/tree/main/Open_Core0)