🐛 Fix missing u8g_esp32_spi (MarlinFirmware#23562)

Marlin/src/HAL/ESP32/u8g_esp32_spi.cpp

@@ -0,0 +1,99 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * Copypaste of SAMD51 HAL developed by Giuliano Zaro (AKA GMagician)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#ifdef ARDUINO_ARCH_ESP32
+
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(FYSETC_MINI_12864_2_1)
+
+#include <U8glib-HAL.h>
+#include "Arduino.h"
+#include "../shared/HAL_SPI.h"
+#include "SPI.h"
+
+static SPISettings spiConfig;
+
+#define MDOGLCD_MOSI    23
+#define MDOGLCD_SCK     18
+#define MLCD_RESET_PIN   0
+#define MLCD_PINS_DC     4
+#define MDOGLCD_CS      21
+#define MDOGLCD_A0       4
+
+#ifndef LCD_SPI_SPEED
+  #ifdef SD_SPI_SPEED
+    #define LCD_SPI_SPEED SD_SPI_SPEED    // Assume SPI speed shared with SD
+  #else
+    #define LCD_SPI_SPEED SPI_FULL_SPEED  // Use full speed if SD speed is not supplied
+  #endif
+#endif
+
+uint8_t u8g_eps_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
+  static uint8_t msgInitCount = 2; // Ignore all messages until 2nd U8G_COM_MSG_INIT
+  if (msgInitCount) {
+    if (msg == U8G_COM_MSG_INIT) msgInitCount--;
+    if (msgInitCount) return -1;
+  }
+
+  switch (msg) {
+    case U8G_COM_MSG_STOP: break;
+
+    case U8G_COM_MSG_INIT:
+      OUT_WRITE(MDOGLCD_CS, HIGH);
+      OUT_WRITE(MDOGLCD_A0, HIGH);
+      OUT_WRITE(MLCD_RESET_PIN, HIGH);
+      u8g_Delay(5);
+      spiBegin();
+      spiInit(LCD_SPI_SPEED);
+      break;
+
+    case U8G_COM_MSG_ADDRESS:           /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
+      WRITE(MDOGLCD_A0, arg_val ? HIGH : LOW);
+      break;
+
+    case U8G_COM_MSG_CHIP_SELECT:       /* arg_val == 0 means HIGH level of U8G_PI_CS */
+      WRITE(MDOGLCD_CS, arg_val ? LOW : HIGH);
+      break;
+
+    case U8G_COM_MSG_RESET:
+      WRITE(MLCD_RESET_PIN, arg_val);
+      break;
+
+    case U8G_COM_MSG_WRITE_BYTE:
+      spiSend((uint8_t)arg_val);
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ:
+      uint8_t *ptr = (uint8_t*) arg_ptr;
+      while (arg_val > 0) {
+        spiSend(*ptr++);
+        arg_val--;
+      }
+      break;
+  }
+  return 1;
+}
+
+#endif // FYSETC_MINI_12864_2_1
+#endif // ARDUINO_ARCH_ESP32

Marlin/src/lcd/dogm/HAL_LCD_com_defines.h

@@ -57,6 +57,11 @@
     #define U8G_COM_HAL_SW_SPI_FN     u8g_com_std_sw_spi_fn
     #define U8G_COM_HAL_HW_SPI_FN     u8g_com_stm32duino_hw_spi_fn
 
+  #elif defined(ESP32)
+
+    uint8_t u8g_eps_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr);
+    #define U8G_COM_HAL_HW_SPI_FN     u8g_eps_hw_spi_fn
+
   #elif defined(__AVR__)
 
     uint8_t u8g_com_HAL_AVR_sw_sp_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr);