Integrate media boards into the rockchip64 family

[ColorfulRhino]

Description

The media board family was long abandoned and most boards that formerly were using this board family already switched to rockchip64 or rk3588. @rpardini recently mentioned being in favor of getting rid of this kernel: #6717 (comment)

Integrate the last remaining boards into rockchip64 and remove the media board family, including its kernel.

GitHub issue reference: #6821
Jira reference number AR-2392

How Has This Been Tested?

• ./compile.sh uboot BOARD=quartz64a BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie
• ./compile.sh uboot BOARD=quartz64b BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie
• ./compile.sh uboot BOARD=station-m1 BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie
• ./compile.sh uboot BOARD=station-p2 BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie
• ./compile.sh kernel BOARD=station-p2 BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie
• ./compile.sh uboot BOARD=firefly-itx-3588j BRANCH=edge BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=no RELEASE=trixie

@SeeleVolleri You can test the Firefly if you like. Your board was using the abandoned U-Boot from the media family. But it should work same as before :)

Checklist:

• My code follows the style guidelines of this project
• I have performed a self-review of my own code
• My changes generate no new warnings
• Any dependent changes have been merged and published in downstream modules

[SeeleVolleri]

Hmm, that's weird. I don't know why, but firefly-itx-3588j won't boot.

DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=2048MB
Manufacturer ID:0xff 
CH0 RX Vref:27.7%, TX Vref:21.8%,0.0%
CH1 RX Vref:26.7%, TX Vref:21.8%,0.0%
CH2 RX Vref:27.7%, TX Vref:21.8%,0.0%
CH3 RX Vref:28.7%, TX Vref:20.8%,0.0%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Jun 19 2024 - 13:59:41)
Trying to boot from MMC2
spl: partition error
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(a7d1d8d191...) + OK
## Checking uboot 0x00200000 ... sha256(51ab307e25...) + OK
## Checking fdt 0x0033faf0 ... sha256(912cda2231...) + OK
## Checking atf-2 0xff100000 ... sha256(4b2065349b...) + OK
## Checking atf-3 0x000f0000 ... sha256(aa71013e72...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 228.919/468.165 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-682-g4ca8a8422:derrick.huang, fwver: v1.45
NOTICE:  BL31: Built : 10:11:21, Dec 27 2023
INFO:    spec: 0x1
INFO:    code: 0x88
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    l3 cache partition cfg-0
INFO:    system boots from cpu-hwid-0
INFO:    disable memory repair
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
ERROR:   dfs get fsp_params[0] error, 0xfead0001 != 0xfead0004
ERROR:   dfs get fsp_params[1] error, 0xa54 != 0xfead0004
ERROR:   dfs get fsp_params[2] error, 0xbc != 0xfead0004
ERROR:   dfs get fsp_params[3] error, 0x3f0033 != 0xfead0004
ERROR:   loader&trust unmatch!!! Please update loader if need enable dmc
ERROR:   current trust bl31 need match with loader ddr bin V1.13 or newer
ERROR:   current loader need match with trust bl31 V1.07-V1.37
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-armbian (Jun 30 2024 - 19:41:44 +0000)

Model: Rockchip RK3588 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: eda1e000
Relocation fdt: eb9fa7c0 - eb9fecd0
CR: M/C/I
Using default environment

optee check api revision fail: -1.0
optee api revision is too low
### ERROR ### Please RESET the board ###

And sorry for late reply.
I'm trying to fix u-boot issues mentioned in that pr #6747
fixed in #6849