Skip to content

ESP32-C3 interfacing to a PS/2 Keyboard (bare-metal Rust)

License

Apache-2.0, MIT licenses found

Licenses found

Apache-2.0
LICENSE-APACHE
MIT
LICENSE-MIT
Notifications You must be signed in to change notification settings

bjoernQ/ps2keyboard-esp32c3

Repository files navigation

ESP32-C3 interfacing to a PS/2 Keyboard (bare-metal Rust)

The example of connecting a PS/2 keyboard and USB keyboard with PS/2 COMBO mode support to ESP32-C3.

You need to build it with the release profile (i.e. cargo run --release) since otherwise the interrupt latency is too slow.

Screenshot

Circuit

  • 2 x 2.2kΩ resitors
  • 2 x 120Ω resitors

    Keyboard                                    ESP32-C3

    5V      ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━  5V

    GND     ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━  GND

                                        ┏━━━━━┓
    DATA    ━━━━━━━━━━━━━━━━━━━━━┳━━━━━━┫ 120 ┣━━━  IO1
                                 ┃      ┗━━━━━┛
                                ┏┻┓
                                ┃2┃
                                ┃.┃
                                ┃2┃
                                ┃k┃
                                ┗┳┛
                                 ┃
                                 ┣━━━━━━━━━━━━━━━━  3V3
                                 ┃
                                ┏┻┓
                                ┃2┃
                                ┃.┃
                                ┃2┃
                                ┃k┃
                                ┗┳┛
                                 ┃      ┏━━━━━┓
    CLK     ━━━━━━━━━━━━━━━━━━━━━┻━━━━━━┫ 120 ┣━━━  IO2
                                        ┗━━━━━┛

Wiring to PS/2 connector

The pinout of PS/2 connector is available at Wikipedia.

Hint 1: use wire wrapping to connect wires to PS/2 connector

Hint 2: make sure to flip the PS/2 pinout if connecting to the male part the connector or to the back part of the connector.

Wiring to USB connector

The same circuit works with USB keyboards with PS/2 COMBO mode support. It's sufficient to replace PS/2 connector with USB connector according the schematics USB to PS2 schematics.

Examples

Keyboard to serial converter

The example converts keyboard to serial which can be then consumed by other board. The receiver board can use pc-keyboard crate to decode signals. The following connection is used in RustZX-ESP32 project.

  ESP32-C3 Converter                         ESP32-S3 Receiver

     RX IO4 ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ TX IO17

     TX IO5 ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ RX IO18

     GND    ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ GND

Run: cargo run --release --example keyboard_to_serial

Keyboard to serial converter - Embassy

Async implementation of the converter with Embassy.

Note: CPU must be clocked at 160MHz to decode values properly, the frequency 80 MHz is not sufficient.

Run: cargo run --release --example embassy_keyboard_to_serial --features embassy

About

ESP32-C3 interfacing to a PS/2 Keyboard (bare-metal Rust)

Resources

License

Apache-2.0, MIT licenses found

Licenses found

Apache-2.0
LICENSE-APACHE
MIT
LICENSE-MIT

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published