Merge pull request #42 from torvalds/master

Sync up with Linus

Documentation/devicetree/bindings/mips/cavium/cib.txt

@@ -0,0 +1,43 @@
+* Cavium Interrupt Bus widget
+
+Properties:
+- compatible: "cavium,octeon-7130-cib"
+
+  Compatibility with cn70XX SoCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: Two elements consisting of the addresses of the RAW and EN
+  registers of the CIB block
+
+- cavium,max-bits: The index (zero based) of the highest numbered bit
+  in the CIB block.
+
+- interrupt-parent:  Always the CIU on the SoC.
+
+- interrupts: The CIU line to which the CIB block is connected.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bit within the
+   CIB.  The second cell specifies the triggering semantics of the
+   line.
+
+Example:
+
+	interrupt-controller@107000000e000 {
+		compatible = "cavium,octeon-7130-cib";
+		reg = <0x10700 0x0000e000 0x0 0x8>, /* RAW */
+		      <0x10700 0x0000e100 0x0 0x8>; /* EN */
+		cavium,max-bits = <23>;
+
+		interrupt-controller;
+		interrupt-parent = <&ciu>;
+		interrupts = <1 24>;
+		/* Interrupts are specified by two parts:
+		 * 1) Bit number in the CIB* registers
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		#interrupt-cells = <2>;
+	};

Documentation/filesystems/Locking

@@ -164,8 +164,6 @@ the block device inode.  See there for more details.
 
 --------------------------- file_system_type ---------------------------
 prototypes:
-	int (*get_sb) (struct file_system_type *, int,
-		       const char *, void *, struct vfsmount *);
 	struct dentry *(*mount) (struct file_system_type *, int,
 		       const char *, void *);
 	void (*kill_sb) (struct super_block *);

Documentation/filesystems/overlayfs.txt

@@ -159,6 +159,22 @@ overlay filesystem (though an operation on the name of the file such as
 rename or unlink will of course be noticed and handled).
 
 
+Multiple lower layers
+---------------------
+
+Multiple lower layers can now be given using the the colon (":") as a
+separator character between the directory names.  For example:
+
+  mount -t overlay overlay -olowerdir=/lower1:/lower2:/lower3 /merged
+
+As the example shows, "upperdir=" and "workdir=" may be omitted.  In
+that case the overlay will be read-only.
+
+The specified lower directories will be stacked beginning from the
+rightmost one and going left.  In the above example lower1 will be the
+top, lower2 the middle and lower3 the bottom layer.
+
+
 Non-standard behavior
 ---------------------
 
@@ -196,3 +212,15 @@ Changes to the underlying filesystems while part of a mounted overlay
 filesystem are not allowed.  If the underlying filesystem is changed,
 the behavior of the overlay is undefined, though it will not result in
 a crash or deadlock.
+
+Testsuite
+---------
+
+There's testsuite developed by David Howells at:
+
+  git://git.infradead.org/users/dhowells/unionmount-testsuite.git
+
+Run as root:
+
+  # cd unionmount-testsuite
+  # ./run --ov

MAINTAINERS

@@ -3937,7 +3937,7 @@ S:	Maintained
 F:	drivers/staging/fbtft/
 
 FCOE SUBSYSTEM (libfc, libfcoe, fcoe)
-M:	Robert Love <robert.w.love@intel.com>
+M:	Vasu Dev <vasu.dev@intel.com>
 L:	[email protected]
 W:	www.Open-FCoE.org
 S:	Supported

Makefile

@@ -1,8 +1,8 @@
-VERSION = 3
-PATCHLEVEL = 19
+VERSION = 4
+PATCHLEVEL = 0
 SUBLEVEL = 0
-EXTRAVERSION =
-NAME = Diseased Newt
+EXTRAVERSION = -rc1
+NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*
 # To see a list of typical targets execute "make help"

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -70,6 +70,26 @@
 		};
 	};
 
+	i2c0: i2c@18008000 {
+		compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+		reg = <0x18008000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
+	i2c1: i2c@1800b000 {
+		compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+		reg = <0x1800b000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
 	uart0: serial@18020000 {
 		compatible = "snps,dw-apb-uart";
 		reg = <0x18020000 0x100>;

arch/arm/boot/dts/bcm63138.dtsi

@@ -66,8 +66,9 @@
 			reg = <0x1d000 0x1000>;
 			cache-unified;
 			cache-level = <2>;
-			cache-sets = <16>;
-			cache-size = <0x80000>;
+			cache-size = <524288>;
+			cache-sets = <1024>;
+			cache-line-size = <32>;
 			interrupts = <GIC_PPI 0 IRQ_TYPE_LEVEL_HIGH>;
 		};
 

arch/arm/kernel/perf_event_cpu.c

@@ -231,7 +231,7 @@ static void cpu_pmu_destroy(struct arm_pmu *cpu_pmu)
 /*
  * PMU platform driver and devicetree bindings.
  */
-static struct of_device_id cpu_pmu_of_device_ids[] = {
+static const struct of_device_id cpu_pmu_of_device_ids[] = {
 	{.compatible = "arm,cortex-a17-pmu",	.data = armv7_a17_pmu_init},
 	{.compatible = "arm,cortex-a15-pmu",	.data = armv7_a15_pmu_init},
 	{.compatible = "arm,cortex-a12-pmu",	.data = armv7_a12_pmu_init},

arch/arm/mach-at91/Kconfig

@@ -64,7 +64,6 @@ config SOC_SAMA5D4
 	select SOC_SAMA5
 	select CLKSRC_MMIO
 	select CACHE_L2X0
-	select CACHE_PL310
 	select HAVE_FB_ATMEL
 	select HAVE_AT91_UTMI
 	select HAVE_AT91_SMD

arch/arm/mach-at91/at91rm9200_time.c

@@ -183,7 +183,7 @@ static struct clock_event_device clkevt = {
 void __iomem *at91_st_base;
 EXPORT_SYMBOL_GPL(at91_st_base);
 
-static struct of_device_id at91rm9200_st_timer_ids[] = {
+static const struct of_device_id at91rm9200_st_timer_ids[] = {
 	{ .compatible = "atmel,at91rm9200-st" },
 	{ /* sentinel */ }
 };

arch/arm/mach-at91/generic.h

@@ -35,10 +35,10 @@ extern void __init at91sam9260_pm_init(void);
 extern void __init at91sam9g45_pm_init(void);
 extern void __init at91sam9x5_pm_init(void);
 #else
-void __init at91rm9200_pm_init(void) { }
-void __init at91sam9260_pm_init(void) { }
-void __init at91sam9g45_pm_init(void) { }
-void __init at91sam9x5_pm_init(void) { }
+static inline void __init at91rm9200_pm_init(void) { }
+static inline void __init at91sam9260_pm_init(void) { }
+static inline void __init at91sam9g45_pm_init(void) { }
+static inline void __init at91sam9x5_pm_init(void) { }
 #endif
 
 #endif /* _AT91_GENERIC_H */

arch/arm/mach-at91/pm.c

@@ -226,15 +226,15 @@ void at91_pm_set_standby(void (*at91_standby)(void))
 	}
 }
 
-static struct of_device_id ramc_ids[] = {
+static const struct of_device_id ramc_ids[] __initconst = {
 	{ .compatible = "atmel,at91rm9200-sdramc", .data = at91rm9200_standby },
 	{ .compatible = "atmel,at91sam9260-sdramc", .data = at91sam9_sdram_standby },
 	{ .compatible = "atmel,at91sam9g45-ddramc", .data = at91_ddr_standby },
 	{ .compatible = "atmel,sama5d3-ddramc", .data = at91_ddr_standby },
 	{ /*sentinel*/ }
 };
 
-static void at91_dt_ramc(void)
+static __init void at91_dt_ramc(void)
 {
 	struct device_node *np;
 	const struct of_device_id *of_id;

arch/arm/mach-axxia/axxia.c

@@ -16,7 +16,7 @@
 #include <linux/init.h>
 #include <asm/mach/arch.h>
 
-static const char *axxia_dt_match[] __initconst = {
+static const char *const axxia_dt_match[] __initconst = {
 	"lsi,axm5516",
 	"lsi,axm5516-sim",
 	"lsi,axm5516-emu",

arch/arm/mach-bcm/Kconfig

@@ -68,7 +68,7 @@ config ARCH_BCM_MOBILE
 	  This enables support for systems based on Broadcom mobile SoCs.
 
 config ARCH_BCM_281XX
-	bool "Broadcom BCM281XX SoC family"
+	bool "Broadcom BCM281XX SoC family" if ARCH_MULTI_V7
 	select ARCH_BCM_MOBILE
 	select HAVE_SMP
 	help
@@ -77,7 +77,7 @@ config ARCH_BCM_281XX
 	  variants.
 
 config ARCH_BCM_21664
-	bool "Broadcom BCM21664 SoC family"
+	bool "Broadcom BCM21664 SoC family" if ARCH_MULTI_V7
 	select ARCH_BCM_MOBILE
 	select HAVE_SMP
 	help

arch/arm/mach-bcm/brcmstb.c

@@ -17,7 +17,7 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-static const char *brcmstb_match[] __initconst = {
+static const char *const brcmstb_match[] __initconst = {
 	"brcm,bcm7445",
 	"brcm,brcmstb",
 	NULL

arch/arm/mach-davinci/Kconfig

@@ -32,12 +32,14 @@ config ARCH_DAVINCI_DM646x
 
 config ARCH_DAVINCI_DA830
 	bool "DA830/OMAP-L137/AM17x based system"
+	depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR
 	select ARCH_DAVINCI_DA8XX
 	select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
 	select CP_INTC
 
 config ARCH_DAVINCI_DA850
 	bool "DA850/OMAP-L138/AM18x based system"
+	depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR
 	select ARCH_DAVINCI_DA8XX
 	select CP_INTC
 

arch/arm/mach-davinci/da8xx-dt.c

@@ -20,7 +20,7 @@
 
 #define DA8XX_NUM_UARTS	3
 
-static struct of_device_id da8xx_irq_match[] __initdata = {
+static const struct of_device_id da8xx_irq_match[] __initconst = {
 	{ .compatible = "ti,cp-intc", .data = cp_intc_of_init, },
 	{ }
 };

arch/arm/mach-davinci/mux.c

@@ -30,7 +30,7 @@ static void __iomem *pinmux_base;
 /*
  * Sets the DAVINCI MUX register based on the table
  */
-int __init_or_module davinci_cfg_reg(const unsigned long index)
+int davinci_cfg_reg(const unsigned long index)
 {
 	static DEFINE_SPINLOCK(mux_spin_lock);
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
@@ -101,7 +101,7 @@ int __init_or_module davinci_cfg_reg(const unsigned long index)
 }
 EXPORT_SYMBOL(davinci_cfg_reg);
 
-int __init_or_module davinci_cfg_reg_list(const short pins[])
+int davinci_cfg_reg_list(const short pins[])
 {
 	int i, error = -EINVAL;
 

arch/arm/mach-exynos/exynos.c

@@ -227,7 +227,7 @@ static void __init exynos_dt_machine_init(void)
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-static char const *exynos_dt_compat[] __initconst = {
+static char const *const exynos_dt_compat[] __initconst = {
 	"samsung,exynos3",
 	"samsung,exynos3250",
 	"samsung,exynos4",

arch/arm/mach-exynos/suspend.c

@@ -587,7 +587,7 @@ static struct exynos_pm_data exynos5420_pm_data = {
 	.cpu_suspend	= exynos5420_cpu_suspend,
 };
 
-static struct of_device_id exynos_pmu_of_device_ids[] = {
+static const struct of_device_id exynos_pmu_of_device_ids[] __initconst = {
 	{
 		.compatible = "samsung,exynos3250-pmu",
 		.data = &exynos3250_pm_data,

arch/arm/mach-highbank/highbank.c

@@ -169,7 +169,7 @@ static void __init highbank_init(void)
 		platform_device_register(&highbank_cpuidle_device);
 }
 
-static const char *highbank_match[] __initconst = {
+static const char *const highbank_match[] __initconst = {
 	"calxeda,highbank",
 	"calxeda,ecx-2000",
 	NULL,

arch/arm/mach-hisi/hisilicon.c

@@ -45,7 +45,7 @@ static void __init hi3620_map_io(void)
 	iotable_init(hi3620_io_desc, ARRAY_SIZE(hi3620_io_desc));
 }
 
-static const char *hi3xxx_compat[] __initconst = {
+static const char *const hi3xxx_compat[] __initconst = {
 	"hisilicon,hi3620-hi4511",
 	NULL,
 };
@@ -55,7 +55,7 @@ DT_MACHINE_START(HI3620, "Hisilicon Hi3620 (Flattened Device Tree)")
 	.dt_compat	= hi3xxx_compat,
 MACHINE_END
 
-static const char *hix5hd2_compat[] __initconst = {
+static const char *const hix5hd2_compat[] __initconst = {
 	"hisilicon,hix5hd2",
 	NULL,
 };
@@ -64,7 +64,7 @@ DT_MACHINE_START(HIX5HD2_DT, "Hisilicon HIX5HD2 (Flattened Device Tree)")
 	.dt_compat	= hix5hd2_compat,
 MACHINE_END
 
-static const char *hip04_compat[] __initconst = {
+static const char *const hip04_compat[] __initconst = {
 	"hisilicon,hip04-d01",
 	NULL,
 };
@@ -73,7 +73,7 @@ DT_MACHINE_START(HIP04, "Hisilicon HiP04 (Flattened Device Tree)")
 	.dt_compat	= hip04_compat,
 MACHINE_END
 
-static const char *hip01_compat[] __initconst = {
+static const char *const hip01_compat[] __initconst = {
 	"hisilicon,hip01",
 	"hisilicon,hip01-ca9x2",
 	NULL,

arch/arm/mach-imx/mmdc.c

@@ -68,7 +68,7 @@ int imx_mmdc_get_ddr_type(void)
 	return ddr_type;
 }
 
-static struct of_device_id imx_mmdc_dt_ids[] = {
+static const struct of_device_id imx_mmdc_dt_ids[] = {
 	{ .compatible = "fsl,imx6q-mmdc", },
 	{ /* sentinel */ }
 };