ARM: tegra: Add device-tree for ASUS Transformer Prime TF201 #13

clamor-s · 2020-12-10T16:46:03Z

We were working, were working, and finally, oh GOD, we made it boot and a tonn of staff working...on TF201.

@digetx may you squash this commit into my previous commit with same name? Use name of original and description of this one.

Hope tree is good enough for this stage. If doesn't brake build this time. Check TF201 PmOS wiki page)

…TF201 Add device-tree for ASUS Transformer Prime TF201, which is NVIDIA Tegra30-based tablet device. Signed-off-by: Svyatoslav Ryhel <[email protected]> Signed-off-by: Ion Agorria <[email protected]>

digetx

Congratulations with getting it to work! Could you please should output of dmesg, /sys/kernel/debug/clk/clk_summary, /sys/kernel/debug/regulator/regulator_summary and /sys/kernel/debug/pm_genpd/pm_genpd_summary?

arch/arm/boot/dts/tegra30-asus-tf201.dts

clamor-s · 2020-12-11T12:50:35Z

@digetx you may find all logs you asked on my GDrive Any help is welcome!

digetx · 2020-12-12T12:43:50Z

The logs look okay in general, you'll need to fix USB host and figure out what causes the timeouts. For USB you probably need to set a proper VBUS-supply regulator in the device-tree.

I added ed2ba04 which was used for debugging pinmux problems on Nexus 7 and A500.

Grab output of the following files from grate-kernel and from downstream kernel, show it to me:

/sys/kernel/debug/tegra_pinmux
/sys/kernel/debug/tegra_pinmux_drive
/sys/kernel/debug/tegra_gpio

clamor-s · 2020-12-12T13:04:24Z

@digetx eventually Ion Aggoria fixed USB host. Original 3.1 kernel has no regulators for that (so no control gpios are available). I analyzed trees of grouper, picasso and ouya and found that vbus can be supplied directly by 5v regulator, since all additional regs descend from 5v.

Check folder above, I've uploaded zip with pinmux logs.

digetx · 2020-12-13T07:00:43Z

Thanks, I answered to Meowin on #tegra irc.

Ido Schimmel says: ==================== mlxsw: Introduce initial XM router support This patch set implements initial eXtended Mezzanine (XM) router support. The XM is an external device connected to the Spectrum-{2,3} ASICs using dedicated Ethernet ports. Its purpose is to increase the number of routes that can be offloaded to hardware. This is achieved by having the ASIC act as a cache that refers cache misses to the XM where the FIB is stored and LPM lookup is performed. Future patch sets will add more sophisticated cache flushing and selftests that utilize cache counters on the ASIC, which we plan to expose via devlink-metric [1]. Patch set overview: Patches #1-#2 add registers to insert/remove routes to/from the XM and to enable/disable it. Patch #3 utilizes these registers in order to implement XM-specific router low-level operations. Patches #4-#5 query from firmware the availability of the XM and the local ports that are used to connect the ASIC to the XM, so that netdevs will not be created for them. Patches #6-#8 initialize the XM by configuring its cache parameters. Patch #9-#10 implement cache management, so that LPM lookup will be correctly cached in the ASIC. Patches #11-#13 implement cache flushing, so that routes insertions/removals to/from the XM will flush the affected entries in the cache. Patch #14 configures the ASIC to allocate half of its memory for the cache, so that room will be left for other entries (e.g., FDBs, neighbours). Patch #15 starts using the XM for IPv4 route offload, when available. [1] https://lore.kernel.org/netdev/[email protected]/ ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Bpftool used to issue forward declarations for a struct used as part of a pointer to array, which is invalid. Add a test to check that the struct is fully defined in this case: @@ -134,9 +134,9 @@ }; }; -struct struct_in_array {}; +struct struct_in_array; -struct struct_in_array_typed {}; +struct struct_in_array_typed; typedef struct struct_in_array_typed struct_in_array_t[2]; @@ -189,3 +189,7 @@ struct struct_with_embedded_stuff _14; }; +struct struct_in_array {}; + +struct struct_in_array_typed {}; + ... #13/1 btf_dump: syntax:FAIL Suggested-by: Andrii Nakryiko <[email protected]> Signed-off-by: Jean-Philippe Brucker <[email protected]> Signed-off-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]

I got several memory leak reports from Asan with a simple command. It was because VDSO is not released due to the refcount. Like in __dsos_addnew_id(), it should put the refcount after adding to the list. $ perf record true [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.030 MB perf.data (10 samples) ] ================================================================= ==692599==ERROR: LeakSanitizer: detected memory leaks Direct leak of 439 byte(s) in 1 object(s) allocated from: #0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154 #1 0x559bce4aa8ee in dso__new_id util/dso.c:1256 #2 0x559bce59245a in __machine__addnew_vdso util/vdso.c:132 #3 0x559bce59245a in machine__findnew_vdso util/vdso.c:347 #4 0x559bce50826c in map__new util/map.c:175 #5 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787 #6 0x559bce512f6b in machines__deliver_event util/session.c:1481 #7 0x559bce515107 in perf_session__deliver_event util/session.c:1551 #8 0x559bce51d4d2 in do_flush util/ordered-events.c:244 #9 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323 #10 0x559bce519bea in __perf_session__process_events util/session.c:2268 #11 0x559bce519bea in perf_session__process_events util/session.c:2297 #12 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017 #13 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234 #14 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026 #15 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858 #16 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313 #17 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365 #18 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409 #19 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539 #20 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308 Indirect leak of 32 byte(s) in 1 object(s) allocated from: #0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154 #1 0x559bce520907 in nsinfo__copy util/namespaces.c:169 #2 0x559bce50821b in map__new util/map.c:168 #3 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787 #4 0x559bce512f6b in machines__deliver_event util/session.c:1481 #5 0x559bce515107 in perf_session__deliver_event util/session.c:1551 #6 0x559bce51d4d2 in do_flush util/ordered-events.c:244 #7 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323 #8 0x559bce519bea in __perf_session__process_events util/session.c:2268 #9 0x559bce519bea in perf_session__process_events util/session.c:2297 #10 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017 #11 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234 #12 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026 #13 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858 #14 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313 #15 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365 #16 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409 #17 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539 #18 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308 SUMMARY: AddressSanitizer: 471 byte(s) leaked in 2 allocation(s). Signed-off-by: Namhyung Kim <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100/0x480 [ 3.362175 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.362175 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.362175 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.362175 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.362175 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.362175 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.362175 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.362175 ] ? vprintk+0x76/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Dumping ftrace buffer: [ 3.362175 ] (ftrace buffer empty) [ 3.362175 ] Kernel Offset: disabled [ 3.362175 ] Rebooting in 1 seconds.. Reported-by: Zheyu Ma <[email protected]> Signed-off-by: Zheyu Ma <[email protected]> Signed-off-by: David S. Miller <[email protected]>

[ Upstream commit 9f6f852 ] 'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e grate-driver#13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e grate-driver#13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100/0x480 [ 3.362175 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.362175 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.362175 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.362175 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.362175 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.362175 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.362175 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.362175 ] ? vprintk+0x76/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Dumping ftrace buffer: [ 3.362175 ] (ftrace buffer empty) [ 3.362175 ] Kernel Offset: disabled [ 3.362175 ] Rebooting in 1 seconds.. Reported-by: Zheyu Ma <[email protected]> Signed-off-by: Zheyu Ma <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 7cf64b1 upstream. vt_in_use() dereferences console_driver->ttys[i] without proper locking. This is broken because the tty can be closed and freed concurrently. We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL' and skipping the check of tty_struct::count. But, looking at console_driver->ttys[i] isn't really appropriate anyway because even if it is NULL the tty can still be in the process of being closed. Instead, fix it by making vt_in_use() require console_lock() and check whether the vt is allocated and has port refcount > 1. This works since following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console" the port refcount is incremented while the vt is open. Reproducer (very unreliable, but it worked for me after a few minutes): #include <fcntl.h> #include <linux/vt.h> int main() { int fd, nproc; struct vt_stat state; char ttyname[16]; fd = open("/dev/tty10", O_RDONLY); for (nproc = 1; nproc < 8; nproc *= 2) fork(); for (;;) { sprintf(ttyname, "/dev/tty%d", rand() % 8); close(open(ttyname, O_RDONLY)); ioctl(fd, VT_GETSTATE, &state); } } KASAN report: BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline] BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657 Read of size 4 at addr ffff888065722468 by task syz-vt2/132 CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 grate-driver#13 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014 Call Trace: [...] vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline] vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657 tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660 [...] Allocated by task 136: [...] kzalloc include/linux/slab.h:669 [inline] alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982 tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334 tty_open_by_driver drivers/tty/tty_io.c:1987 [inline] tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035 [...] Freed by task 41: [...] kfree+0xbf/0x200 mm/slab.c:3757 free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177 release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468 process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264 worker_thread+0x8b/0xc80 kernel/workqueue.c:2410 [...] Fixes: 4001d7b ("vt: push down the tty lock so we can see what is left to tackle") Cc: <[email protected]> # v3.4+ Acked-by: Jiri Slaby <[email protected]> Signed-off-by: Eric Biggers <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 7b01b72 ] When the nvmem framework is enabled, a nvmem device is created per mtd device/partition. It is not uncommon that a device can have multiple mtd devices with partitions that have the same name. Eg, when there DT overlay is allowed and the same device with mtd is attached twice. Under that circumstances, the mtd fails to register due to a name duplication on the nvmem framework. With this patch we use the mtdX name instead of the partition name, which is unique. [ 8.948991] sysfs: cannot create duplicate filename '/bus/nvmem/devices/Production Data' [ 8.948992] CPU: 7 PID: 246 Comm: systemd-udevd Not tainted 5.5.0-qtec-standard grate-driver#13 [ 8.948993] Hardware name: AMD Dibbler/Dibbler, BIOS 05.22.04.0019 10/26/2019 [ 8.948994] Call Trace: [ 8.948996] dump_stack+0x50/0x70 [ 8.948998] sysfs_warn_dup.cold+0x17/0x2d [ 8.949000] sysfs_do_create_link_sd.isra.0+0xc2/0xd0 [ 8.949002] bus_add_device+0x74/0x140 [ 8.949004] device_add+0x34b/0x850 [ 8.949006] nvmem_register.part.0+0x1bf/0x640 ... [ 8.948926] mtd mtd8: Failed to register NVMEM device Fixes: c4dfa25 ("mtd: add support for reading MTD devices via the nvmem API") Signed-off-by: Ricardo Ribalda Delgado <[email protected]> Acked-by: Miquel Raynal <[email protected]> Signed-off-by: Richard Weinberger <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

ASan reports a memory leak caused by evlist not being deleted on exit in perf-report, perf-script and perf-data. The problem is caused by evlist->session not being deleted, which is allocated in perf_session__read_header, called in perf_session__new if perf_data is in read mode. In case of write mode, the session->evlist is filled by the caller. This patch solves the problem by calling evlist__delete in perf_session__delete if perf_data is in read mode. Changes in v2: - call evlist__delete from within perf_session__delete v1: https://lore.kernel.org/lkml/[email protected]/ ASan report follows: $ ./perf script report flamegraph ================================================================= ==227640==ERROR: LeakSanitizer: detected memory leaks <SNIP unrelated> Indirect leak of 2704 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0x7f999e in evlist__new /home/user/linux/tools/perf/util/evlist.c:77:26 #3 0x8ad938 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3797:20 #4 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #5 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #6 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #7 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #8 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #9 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #10 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #11 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 568 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0x80ce88 in evsel__new_idx /home/user/linux/tools/perf/util/evsel.c:268:24 #3 0x8aed93 in evsel__new /home/user/linux/tools/perf/util/evsel.h:210:9 #4 0x8ae07e in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3853:11 #5 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #6 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #7 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #8 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #9 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #10 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #11 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #12 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 264 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0xbe3e70 in xyarray__new /home/user/linux/tools/lib/perf/xyarray.c:10:23 #3 0xbd7754 in perf_evsel__alloc_id /home/user/linux/tools/lib/perf/evsel.c:361:21 #4 0x8ae201 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3871:7 #5 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #6 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #7 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #8 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #9 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #10 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #11 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #12 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 32 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0xbd77e0 in perf_evsel__alloc_id /home/user/linux/tools/lib/perf/evsel.c:365:14 #3 0x8ae201 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3871:7 #4 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #5 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #6 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #7 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #8 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #9 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #10 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #11 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 7 byte(s) in 1 object(s) allocated from: #0 0x4b8207 in strdup (/home/user/linux/tools/perf/perf+0x4b8207) #1 0x8b4459 in evlist__set_event_name /home/user/linux/tools/perf/util/header.c:2292:16 #2 0x89d862 in process_event_desc /home/user/linux/tools/perf/util/header.c:2313:3 #3 0x8af319 in perf_file_section__process /home/user/linux/tools/perf/util/header.c:3651:9 #4 0x8aa6e9 in perf_header__process_sections /home/user/linux/tools/perf/util/header.c:3427:9 #5 0x8ae3e7 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3886:2 #6 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #7 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #8 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #9 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #10 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #11 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #12 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #13 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) SUMMARY: AddressSanitizer: 3728 byte(s) leaked in 7 allocation(s). Signed-off-by: Riccardo Mancini <[email protected]> Acked-by: Ian Rogers <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Kan Liang <[email protected]> Cc: Leo Yan <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

ASan reports a heap-buffer-overflow in elf_sec__is_text when using perf-top. The bug is caused by the fact that secstrs is built from runtime_ss, while shdr is built from syms_ss if shdr.sh_type != SHT_NOBITS. Therefore, they point to two different ELF files. This patch renames secstrs to secstrs_run and adds secstrs_sym, so that the correct secstrs is chosen depending on shdr.sh_type. $ ASAN_OPTIONS=abort_on_error=1:disable_coredump=0:unmap_shadow_on_exit=1 ./perf top ================================================================= ==363148==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x61300009add6 at pc 0x00000049875c bp 0x7f4f56446440 sp 0x7f4f56445bf0 READ of size 1 at 0x61300009add6 thread T6 #0 0x49875b in StrstrCheck(void*, char*, char const*, char const*) (/home/user/linux/tools/perf/perf+0x49875b) #1 0x4d13a2 in strstr (/home/user/linux/tools/perf/perf+0x4d13a2) #2 0xacae36 in elf_sec__is_text /home/user/linux/tools/perf/util/symbol-elf.c:176:9 #3 0xac3ec9 in elf_sec__filter /home/user/linux/tools/perf/util/symbol-elf.c:187:9 #4 0xac2c3d in dso__load_sym /home/user/linux/tools/perf/util/symbol-elf.c:1254:20 #5 0x883981 in dso__load /home/user/linux/tools/perf/util/symbol.c:1897:9 #6 0x8e6248 in map__load /home/user/linux/tools/perf/util/map.c:332:7 #7 0x8e66e5 in map__find_symbol /home/user/linux/tools/perf/util/map.c:366:6 #8 0x7f8278 in machine__resolve /home/user/linux/tools/perf/util/event.c:707:13 #9 0x5f3d1a in perf_event__process_sample /home/user/linux/tools/perf/builtin-top.c:773:6 #10 0x5f30e4 in deliver_event /home/user/linux/tools/perf/builtin-top.c:1197:3 #11 0x908a72 in do_flush /home/user/linux/tools/perf/util/ordered-events.c:244:9 #12 0x905fae in __ordered_events__flush /home/user/linux/tools/perf/util/ordered-events.c:323:8 #13 0x9058db in ordered_events__flush /home/user/linux/tools/perf/util/ordered-events.c:341:9 #14 0x5f19b1 in process_thread /home/user/linux/tools/perf/builtin-top.c:1109:7 #15 0x7f4f6a21a298 in start_thread /usr/src/debug/glibc-2.33-16.fc34.x86_64/nptl/pthread_create.c:481:8 #16 0x7f4f697d0352 in clone ../sysdeps/unix/sysv/linux/x86_64/clone.S:95 0x61300009add6 is located 10 bytes to the right of 332-byte region [0x61300009ac80,0x61300009adcc) allocated by thread T6 here: #0 0x4f3f7f in malloc (/home/user/linux/tools/perf/perf+0x4f3f7f) #1 0x7f4f6a0a88d9 (/lib64/libelf.so.1+0xa8d9) Thread T6 created by T0 here: #0 0x464856 in pthread_create (/home/user/linux/tools/perf/perf+0x464856) #1 0x5f06e0 in __cmd_top /home/user/linux/tools/perf/builtin-top.c:1309:6 #2 0x5ef19f in cmd_top /home/user/linux/tools/perf/builtin-top.c:1762:11 #3 0x7b28c0 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #4 0x7b119f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #5 0x7b2423 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #6 0x7b0c19 in main /home/user/linux/tools/perf/perf.c:539:3 #7 0x7f4f696f7b74 in __libc_start_main /usr/src/debug/glibc-2.33-16.fc34.x86_64/csu/../csu/libc-start.c:332:16 SUMMARY: AddressSanitizer: heap-buffer-overflow (/home/user/linux/tools/perf/perf+0x49875b) in StrstrCheck(void*, char*, char const*, char const*) Shadow bytes around the buggy address: 0x0c268000b560: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa 0x0c268000b570: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa 0x0c268000b580: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa 0x0c268000b590: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0c268000b5a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 =>0x0c268000b5b0: 00 00 00 00 00 00 00 00 00 04[fa]fa fa fa fa fa 0x0c268000b5c0: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 0x0c268000b5d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0c268000b5e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0c268000b5f0: 07 fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa 0x0c268000b600: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd Shadow byte legend (one shadow byte represents 8 application bytes): Addressable: 00 Partially addressable: 01 02 03 04 05 06 07 Heap left redzone: fa Freed heap region: fd Stack left redzone: f1 Stack mid redzone: f2 Stack right redzone: f3 Stack after return: f5 Stack use after scope: f8 Global redzone: f9 Global init order: f6 Poisoned by user: f7 Container overflow: fc Array cookie: ac Intra object redzone: bb ASan internal: fe Left alloca redzone: ca Right alloca redzone: cb Shadow gap: cc ==363148==ABORTING Suggested-by: Jiri Slaby <[email protected]> Signed-off-by: Riccardo Mancini <[email protected]> Acked-by: Namhyung Kim <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Fabian Hemmer <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Jiri Slaby <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Remi Bernon <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

When TEE target mirrors traffic to another interface, sk_buff may not have enough headroom to be processed correctly. ip_finish_output2() detect this situation for ipv4 and allocates new skb with enogh headroom. However ipv6 lacks this logic in ip_finish_output2 and it leads to skb_under_panic: skbuff: skb_under_panic: text:ffffffffc0866ad4 len:96 put:24 head:ffff97be85e31800 data:ffff97be85e317f8 tail:0x58 end:0xc0 dev:gre0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:110! invalid opcode: 0000 [#1] SMP PTI CPU: 2 PID: 393 Comm: kworker/2:2 Tainted: G OE 5.13.0 #13 Hardware name: Virtuozzo KVM, BIOS 1.11.0-2.vz7.4 04/01/2014 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:skb_panic+0x48/0x4a Call Trace: skb_push.cold.111+0x10/0x10 ipgre_header+0x24/0xf0 [ip_gre] neigh_connected_output+0xae/0xf0 ip6_finish_output2+0x1a8/0x5a0 ip6_output+0x5c/0x110 nf_dup_ipv6+0x158/0x1000 [nf_dup_ipv6] tee_tg6+0x2e/0x40 [xt_TEE] ip6t_do_table+0x294/0x470 [ip6_tables] nf_hook_slow+0x44/0xc0 nf_hook.constprop.34+0x72/0xe0 ndisc_send_skb+0x20d/0x2e0 ndisc_send_ns+0xd1/0x210 addrconf_dad_work+0x3c8/0x540 process_one_work+0x1d1/0x370 worker_thread+0x30/0x390 kthread+0x116/0x130 ret_from_fork+0x22/0x30 Signed-off-by: Vasily Averin <[email protected]> Signed-off-by: David S. Miller <[email protected]>

In __htab_map_lookup_and_delete_batch(), hash buckets are iterated over to count the number of elements in each bucket (bucket_size). If bucket_size is large enough, the multiplication to calculate kvmalloc() size could overflow, resulting in out-of-bounds write as reported by KASAN: [...] [ 104.986052] BUG: KASAN: vmalloc-out-of-bounds in __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.986489] Write of size 4194224 at addr ffffc9010503be70 by task crash/112 [ 104.986889] [ 104.987193] CPU: 0 PID: 112 Comm: crash Not tainted 5.14.0-rc4 #13 [ 104.987552] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 [ 104.988104] Call Trace: [ 104.988410] dump_stack_lvl+0x34/0x44 [ 104.988706] print_address_description.constprop.0+0x21/0x140 [ 104.988991] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.989327] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.989622] kasan_report.cold+0x7f/0x11b [ 104.989881] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.990239] kasan_check_range+0x17c/0x1e0 [ 104.990467] memcpy+0x39/0x60 [ 104.990670] __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.990982] ? __wake_up_common+0x4d/0x230 [ 104.991256] ? htab_of_map_free+0x130/0x130 [ 104.991541] bpf_map_do_batch+0x1fb/0x220 [...] In hashtable, if the elements' keys have the same jhash() value, the elements will be put into the same bucket. By putting a lot of elements into a single bucket, the value of bucket_size can be increased to trigger the integer overflow. Triggering the overflow is possible for both callers with CAP_SYS_ADMIN and callers without CAP_SYS_ADMIN. It will be trivial for a caller with CAP_SYS_ADMIN to intentionally reach this overflow by enabling BPF_F_ZERO_SEED. As this flag will set the random seed passed to jhash() to 0, it will be easy for the caller to prepare keys which will be hashed into the same value, and thus put all the elements into the same bucket. If the caller does not have CAP_SYS_ADMIN, BPF_F_ZERO_SEED cannot be used. However, it will be still technically possible to trigger the overflow, by guessing the random seed value passed to jhash() (32bit) and repeating the attempt to trigger the overflow. In this case, the probability to trigger the overflow will be low and will take a very long time. Fix the integer overflow by calling kvmalloc_array() instead of kvmalloc() to allocate memory. Fixes: 0579963 ("bpf: Add batch ops to all htab bpf map") Signed-off-by: Tatsuhiko Yasumatsu <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]

[ Upstream commit 5796015 ] When TEE target mirrors traffic to another interface, sk_buff may not have enough headroom to be processed correctly. ip_finish_output2() detect this situation for ipv4 and allocates new skb with enogh headroom. However ipv6 lacks this logic in ip_finish_output2 and it leads to skb_under_panic: skbuff: skb_under_panic: text:ffffffffc0866ad4 len:96 put:24 head:ffff97be85e31800 data:ffff97be85e317f8 tail:0x58 end:0xc0 dev:gre0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:110! invalid opcode: 0000 [#1] SMP PTI CPU: 2 PID: 393 Comm: kworker/2:2 Tainted: G OE 5.13.0 grate-driver#13 Hardware name: Virtuozzo KVM, BIOS 1.11.0-2.vz7.4 04/01/2014 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:skb_panic+0x48/0x4a Call Trace: skb_push.cold.111+0x10/0x10 ipgre_header+0x24/0xf0 [ip_gre] neigh_connected_output+0xae/0xf0 ip6_finish_output2+0x1a8/0x5a0 ip6_output+0x5c/0x110 nf_dup_ipv6+0x158/0x1000 [nf_dup_ipv6] tee_tg6+0x2e/0x40 [xt_TEE] ip6t_do_table+0x294/0x470 [ip6_tables] nf_hook_slow+0x44/0xc0 nf_hook.constprop.34+0x72/0xe0 ndisc_send_skb+0x20d/0x2e0 ndisc_send_ns+0xd1/0x210 addrconf_dad_work+0x3c8/0x540 process_one_work+0x1d1/0x370 worker_thread+0x30/0x390 kthread+0x116/0x130 ret_from_fork+0x22/0x30 Signed-off-by: Vasily Averin <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit c4eb1f4 ] In __htab_map_lookup_and_delete_batch(), hash buckets are iterated over to count the number of elements in each bucket (bucket_size). If bucket_size is large enough, the multiplication to calculate kvmalloc() size could overflow, resulting in out-of-bounds write as reported by KASAN: [...] [ 104.986052] BUG: KASAN: vmalloc-out-of-bounds in __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.986489] Write of size 4194224 at addr ffffc9010503be70 by task crash/112 [ 104.986889] [ 104.987193] CPU: 0 PID: 112 Comm: crash Not tainted 5.14.0-rc4 grate-driver#13 [ 104.987552] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 [ 104.988104] Call Trace: [ 104.988410] dump_stack_lvl+0x34/0x44 [ 104.988706] print_address_description.constprop.0+0x21/0x140 [ 104.988991] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.989327] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.989622] kasan_report.cold+0x7f/0x11b [ 104.989881] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.990239] kasan_check_range+0x17c/0x1e0 [ 104.990467] memcpy+0x39/0x60 [ 104.990670] __htab_map_lookup_and_delete_batch+0x5ce/0xb60 [ 104.990982] ? __wake_up_common+0x4d/0x230 [ 104.991256] ? htab_of_map_free+0x130/0x130 [ 104.991541] bpf_map_do_batch+0x1fb/0x220 [...] In hashtable, if the elements' keys have the same jhash() value, the elements will be put into the same bucket. By putting a lot of elements into a single bucket, the value of bucket_size can be increased to trigger the integer overflow. Triggering the overflow is possible for both callers with CAP_SYS_ADMIN and callers without CAP_SYS_ADMIN. It will be trivial for a caller with CAP_SYS_ADMIN to intentionally reach this overflow by enabling BPF_F_ZERO_SEED. As this flag will set the random seed passed to jhash() to 0, it will be easy for the caller to prepare keys which will be hashed into the same value, and thus put all the elements into the same bucket. If the caller does not have CAP_SYS_ADMIN, BPF_F_ZERO_SEED cannot be used. However, it will be still technically possible to trigger the overflow, by guessing the random seed value passed to jhash() (32bit) and repeating the attempt to trigger the overflow. In this case, the probability to trigger the overflow will be low and will take a very long time. Fix the integer overflow by calling kvmalloc_array() instead of kvmalloc() to allocate memory. Fixes: 0579963 ("bpf: Add batch ops to all htab bpf map") Signed-off-by: Tatsuhiko Yasumatsu <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Link: https://lore.kernel.org/bpf/[email protected] Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 5796015 ] When TEE target mirrors traffic to another interface, sk_buff may not have enough headroom to be processed correctly. ip_finish_output2() detect this situation for ipv4 and allocates new skb with enogh headroom. However ipv6 lacks this logic in ip_finish_output2 and it leads to skb_under_panic: skbuff: skb_under_panic: text:ffffffffc0866ad4 len:96 put:24 head:ffff97be85e31800 data:ffff97be85e317f8 tail:0x58 end:0xc0 dev:gre0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:110! invalid opcode: 0000 [#1] SMP PTI CPU: 2 PID: 393 Comm: kworker/2:2 Tainted: G OE 5.13.0 grate-driver#13 Hardware name: Virtuozzo KVM, BIOS 1.11.0-2.vz7.4 04/01/2014 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:skb_panic+0x48/0x4a Call Trace: skb_push.cold.111+0x10/0x10 ipgre_header+0x24/0xf0 [ip_gre] neigh_connected_output+0xae/0xf0 ip6_finish_output2+0x1a8/0x5a0 ip6_output+0x5c/0x110 nf_dup_ipv6+0x158/0x1000 [nf_dup_ipv6] tee_tg6+0x2e/0x40 [xt_TEE] ip6t_do_table+0x294/0x470 [ip6_tables] nf_hook_slow+0x44/0xc0 nf_hook.constprop.34+0x72/0xe0 ndisc_send_skb+0x20d/0x2e0 ndisc_send_ns+0xd1/0x210 addrconf_dad_work+0x3c8/0x540 process_one_work+0x1d1/0x370 worker_thread+0x30/0x390 kthread+0x116/0x130 ret_from_fork+0x22/0x30 Signed-off-by: Vasily Averin <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 4d14c5c upstream Calling btrfs_qgroup_reserve_meta_prealloc from btrfs_delayed_inode_reserve_metadata can result in flushing delalloc while holding a transaction and delayed node locks. This is deadlock prone. In the past multiple commits: * ae5e070 ("btrfs: qgroup: don't try to wait flushing if we're already holding a transaction") * 6f23277 ("btrfs: qgroup: don't commit transaction when we already hold the handle") Tried to solve various aspects of this but this was always a whack-a-mole game. Unfortunately those 2 fixes don't solve a deadlock scenario involving btrfs_delayed_node::mutex. Namely, one thread can call btrfs_dirty_inode as a result of reading a file and modifying its atime: PID: 6963 TASK: ffff8c7f3f94c000 CPU: 2 COMMAND: "test" #0 __schedule at ffffffffa529e07d #1 schedule at ffffffffa529e4ff #2 schedule_timeout at ffffffffa52a1bdd #3 wait_for_completion at ffffffffa529eeea <-- sleeps with delayed node mutex held #4 start_delalloc_inodes at ffffffffc0380db5 #5 btrfs_start_delalloc_snapshot at ffffffffc0393836 #6 try_flush_qgroup at ffffffffc03f04b2 #7 __btrfs_qgroup_reserve_meta at ffffffffc03f5bb6 <-- tries to reserve space and starts delalloc inodes. #8 btrfs_delayed_update_inode at ffffffffc03e31aa <-- acquires delayed node mutex grate-driver#9 btrfs_update_inode at ffffffffc0385ba8 grate-driver#10 btrfs_dirty_inode at ffffffffc038627b <-- TRANSACTIION OPENED grate-driver#11 touch_atime at ffffffffa4cf0000 grate-driver#12 generic_file_read_iter at ffffffffa4c1f123 grate-driver#13 new_sync_read at ffffffffa4ccdc8a grate-driver#14 vfs_read at ffffffffa4cd0849 grate-driver#15 ksys_read at ffffffffa4cd0bd1 grate-driver#16 do_syscall_64 at ffffffffa4a052eb grate-driver#17 entry_SYSCALL_64_after_hwframe at ffffffffa540008c This will cause an asynchronous work to flush the delalloc inodes to happen which can try to acquire the same delayed_node mutex: PID: 455 TASK: ffff8c8085fa4000 CPU: 5 COMMAND: "kworker/u16:30" #0 __schedule at ffffffffa529e07d #1 schedule at ffffffffa529e4ff #2 schedule_preempt_disabled at ffffffffa529e80a #3 __mutex_lock at ffffffffa529fdcb <-- goes to sleep, never wakes up. #4 btrfs_delayed_update_inode at ffffffffc03e3143 <-- tries to acquire the mutex #5 btrfs_update_inode at ffffffffc0385ba8 <-- this is the same inode that pid 6963 is holding #6 cow_file_range_inline.constprop.78 at ffffffffc0386be7 #7 cow_file_range at ffffffffc03879c1 #8 btrfs_run_delalloc_range at ffffffffc038894c grate-driver#9 writepage_delalloc at ffffffffc03a3c8f grate-driver#10 __extent_writepage at ffffffffc03a4c01 grate-driver#11 extent_write_cache_pages at ffffffffc03a500b grate-driver#12 extent_writepages at ffffffffc03a6de2 grate-driver#13 do_writepages at ffffffffa4c277eb grate-driver#14 __filemap_fdatawrite_range at ffffffffa4c1e5bb grate-driver#15 btrfs_run_delalloc_work at ffffffffc0380987 <-- starts running delayed nodes grate-driver#16 normal_work_helper at ffffffffc03b706c grate-driver#17 process_one_work at ffffffffa4aba4e4 grate-driver#18 worker_thread at ffffffffa4aba6fd grate-driver#19 kthread at ffffffffa4ac0a3d grate-driver#20 ret_from_fork at ffffffffa54001ff To fully address those cases the complete fix is to never issue any flushing while holding the transaction or the delayed node lock. This patch achieves it by calling qgroup_reserve_meta directly which will either succeed without flushing or will fail and return -EDQUOT. In the latter case that return value is going to be propagated to btrfs_dirty_inode which will fallback to start a new transaction. That's fine as the majority of time we expect the inode will have BTRFS_DELAYED_NODE_INODE_DIRTY flag set which will result in directly copying the in-memory state. Fixes: c53e965 ("btrfs: qgroup: try to flush qgroup space when we get -EDQUOT") CC: [email protected] # 5.10+ Reviewed-by: Qu Wenruo <[email protected]> Signed-off-by: Nikolay Borisov <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Anand Jain <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 9f6f852 ] 'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e grate-driver#13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e grate-driver#13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100/0x480 [ 3.362175 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.362175 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.362175 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.362175 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.362175 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.362175 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.362175 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.362175 ] ? vprintk+0x76/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Dumping ftrace buffer: [ 3.362175 ] (ftrace buffer empty) [ 3.362175 ] Kernel Offset: disabled [ 3.362175 ] Rebooting in 1 seconds.. Reported-by: Zheyu Ma <[email protected]> Signed-off-by: Zheyu Ma <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, #13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, #13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

commit 41d5854 upstream. I got several memory leak reports from Asan with a simple command. It was because VDSO is not released due to the refcount. Like in __dsos_addnew_id(), it should put the refcount after adding to the list. $ perf record true [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.030 MB perf.data (10 samples) ] ================================================================= ==692599==ERROR: LeakSanitizer: detected memory leaks Direct leak of 439 byte(s) in 1 object(s) allocated from: #0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154 #1 0x559bce4aa8ee in dso__new_id util/dso.c:1256 #2 0x559bce59245a in __machine__addnew_vdso util/vdso.c:132 #3 0x559bce59245a in machine__findnew_vdso util/vdso.c:347 #4 0x559bce50826c in map__new util/map.c:175 #5 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787 #6 0x559bce512f6b in machines__deliver_event util/session.c:1481 #7 0x559bce515107 in perf_session__deliver_event util/session.c:1551 #8 0x559bce51d4d2 in do_flush util/ordered-events.c:244 grate-driver#9 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323 grate-driver#10 0x559bce519bea in __perf_session__process_events util/session.c:2268 grate-driver#11 0x559bce519bea in perf_session__process_events util/session.c:2297 grate-driver#12 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017 grate-driver#13 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234 grate-driver#14 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026 grate-driver#15 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858 grate-driver#16 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313 grate-driver#17 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365 grate-driver#18 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409 grate-driver#19 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539 grate-driver#20 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308 Indirect leak of 32 byte(s) in 1 object(s) allocated from: #0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154 #1 0x559bce520907 in nsinfo__copy util/namespaces.c:169 #2 0x559bce50821b in map__new util/map.c:168 #3 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787 #4 0x559bce512f6b in machines__deliver_event util/session.c:1481 #5 0x559bce515107 in perf_session__deliver_event util/session.c:1551 #6 0x559bce51d4d2 in do_flush util/ordered-events.c:244 #7 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323 #8 0x559bce519bea in __perf_session__process_events util/session.c:2268 grate-driver#9 0x559bce519bea in perf_session__process_events util/session.c:2297 grate-driver#10 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017 grate-driver#11 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234 grate-driver#12 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026 grate-driver#13 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858 grate-driver#14 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313 grate-driver#15 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365 grate-driver#16 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409 grate-driver#17 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539 grate-driver#18 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308 SUMMARY: AddressSanitizer: 471 byte(s) leaked in 2 allocation(s). Signed-off-by: Namhyung Kim <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Hanjun Guo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, #13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, grate-driver#13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

It's later supposed to be either a correct address or NULL. Without the initialization, it may contain an undefined value which results in the following segmentation fault: # perf top --sort comm -g --ignore-callees=do_idle terminates with: #0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6 #1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6 #2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489 #3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564 #4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420, sample_self=sample_self@entry=true) at util/hist.c:657 #5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0, sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288 #6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38) at util/hist.c:1056 #7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056 #8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0) at util/hist.c:1231 #9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0) at builtin-top.c:842 #10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202 #11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244 #12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323 #13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339 #14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341 #15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339 #16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114 #17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0 #18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6 If you look at the frame #2, the code is: 488 if (he->srcline) { 489 he->srcline = strdup(he->srcline); 490 if (he->srcline == NULL) 491 goto err_rawdata; 492 } If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish), it gets strdupped and strdupping a rubbish random string causes the problem. Also, if you look at the commit 1fb7d06, it adds the srcline property into the struct, but not initializing it everywhere needed. Committer notes: Now I see, when using --ignore-callees=do_idle we end up here at line 2189 in add_callchain_ip(): 2181 if (al.sym != NULL) { 2182 if (perf_hpp_list.parent && !*parent && 2183 symbol__match_regex(al.sym, &parent_regex)) 2184 *parent = al.sym; 2185 else if (have_ignore_callees && root_al && 2186 symbol__match_regex(al.sym, &ignore_callees_regex)) { 2187 /* Treat this symbol as the root, 2188 forgetting its callees. */ 2189 *root_al = al; 2190 callchain_cursor_reset(cursor); 2191 } 2192 } And the al that doesn't have the ->srcline field initialized will be copied to the root_al, so then, back to: 1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al, 1212 int max_stack_depth, void *arg) 1213 { 1214 int err, err2; 1215 struct map *alm = NULL; 1216 1217 if (al) 1218 alm = map__get(al->map); 1219 1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent, 1221 iter->evsel, al, max_stack_depth); 1222 if (err) { 1223 map__put(alm); 1224 return err; 1225 } 1226 1227 err = iter->ops->prepare_entry(iter, al); 1228 if (err) 1229 goto out; 1230 1231 err = iter->ops->add_single_entry(iter, al); 1232 if (err) 1233 goto out; 1234 That al at line 1221 is what hist_entry_iter__add() (called from sample__resolve_callchain()) saw as 'root_al', and then: iter->ops->add_single_entry(iter, al); will go on with al->srcline with a bogus value, I'll add the above sequence to the cset and apply, thanks! Signed-off-by: Michael Petlan <[email protected]> CC: Milian Wolff <[email protected]> Cc: Jiri Olsa <[email protected]> Fixes: 1fb7d06 ("perf report Use srcline from callchain for hist entries") Link: https //lore.kernel.org/r/[email protected] Reported-by: Juri Lelli <[email protected]> Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, #13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dcc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, grate-driver#13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in link: [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/ Fixes: 4210157 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <[email protected]>

Attempting to defragment a Btrfs file containing a transparent huge page immediately deadlocks with the following stack trace: #0 context_switch (kernel/sched/core.c:4940:2) #1 __schedule (kernel/sched/core.c:6287:8) #2 schedule (kernel/sched/core.c:6366:3) #3 io_schedule (kernel/sched/core.c:8389:2) #4 wait_on_page_bit_common (mm/filemap.c:1356:4) #5 __lock_page (mm/filemap.c:1648:2) #6 lock_page (./include/linux/pagemap.h:625:3) #7 pagecache_get_page (mm/filemap.c:1910:4) #8 find_or_create_page (./include/linux/pagemap.h:420:9) #9 defrag_prepare_one_page (fs/btrfs/ioctl.c:1068:9) #10 defrag_one_range (fs/btrfs/ioctl.c:1326:14) #11 defrag_one_cluster (fs/btrfs/ioctl.c:1421:9) #12 btrfs_defrag_file (fs/btrfs/ioctl.c:1523:9) #13 btrfs_ioctl_defrag (fs/btrfs/ioctl.c:3117:9) #14 btrfs_ioctl (fs/btrfs/ioctl.c:4872:10) #15 vfs_ioctl (fs/ioctl.c:51:10) #16 __do_sys_ioctl (fs/ioctl.c:874:11) #17 __se_sys_ioctl (fs/ioctl.c:860:1) #18 __x64_sys_ioctl (fs/ioctl.c:860:1) #19 do_syscall_x64 (arch/x86/entry/common.c:50:14) #20 do_syscall_64 (arch/x86/entry/common.c:80:7) #21 entry_SYSCALL_64+0x7c/0x15b (arch/x86/entry/entry_64.S:113) A huge page is represented by a compound page, which consists of a struct page for each PAGE_SIZE page within the huge page. The first struct page is the "head page", and the remaining are "tail pages". Defragmentation attempts to lock each page in the range. However, lock_page() on a tail page actually locks the corresponding head page. So, if defragmentation tries to lock more than one struct page in a compound page, it tries to lock the same head page twice and deadlocks with itself. Ideally, we should be able to defragment transparent huge pages. However, THP for filesystems is currently read-only, so a lot of code is not ready to use huge pages for I/O. For now, let's just return ETXTBUSY. This can be reproduced with the following on a kernel with CONFIG_READ_ONLY_THP_FOR_FS=y: $ cat create_thp_file.c #include <fcntl.h> #include <stdbool.h> #include <stdio.h> #include <stdint.h> #include <stdlib.h> #include <unistd.h> #include <sys/mman.h> static const char zeroes[1024 * 1024]; static const size_t FILE_SIZE = 2 * 1024 * 1024; int main(int argc, char **argv) { if (argc != 2) { fprintf(stderr, "usage: %s PATH\n", argv[0]); return EXIT_FAILURE; } int fd = creat(argv[1], 0777); if (fd == -1) { perror("creat"); return EXIT_FAILURE; } size_t written = 0; while (written < FILE_SIZE) { ssize_t ret = write(fd, zeroes, sizeof(zeroes) < FILE_SIZE - written ? sizeof(zeroes) : FILE_SIZE - written); if (ret < 0) { perror("write"); return EXIT_FAILURE; } written += ret; } close(fd); fd = open(argv[1], O_RDONLY); if (fd == -1) { perror("open"); return EXIT_FAILURE; } /* * Reserve some address space so that we can align the file mapping to * the huge page size. */ void *placeholder_map = mmap(NULL, FILE_SIZE * 2, PROT_NONE, MAP_PRIVATE | MAP_ANONYMOUS, -1, 0); if (placeholder_map == MAP_FAILED) { perror("mmap (placeholder)"); return EXIT_FAILURE; } void *aligned_address = (void *)(((uintptr_t)placeholder_map + FILE_SIZE - 1) & ~(FILE_SIZE - 1)); void *map = mmap(aligned_address, FILE_SIZE, PROT_READ | PROT_EXEC, MAP_SHARED | MAP_FIXED, fd, 0); if (map == MAP_FAILED) { perror("mmap"); return EXIT_FAILURE; } if (madvise(map, FILE_SIZE, MADV_HUGEPAGE) < 0) { perror("madvise"); return EXIT_FAILURE; } char *line = NULL; size_t line_capacity = 0; FILE *smaps_file = fopen("/proc/self/smaps", "r"); if (!smaps_file) { perror("fopen"); return EXIT_FAILURE; } for (;;) { for (size_t off = 0; off < FILE_SIZE; off += 4096) ((volatile char *)map)[off]; ssize_t ret; bool this_mapping = false; while ((ret = getline(&line, &line_capacity, smaps_file)) > 0) { unsigned long start, end, huge; if (sscanf(line, "%lx-%lx", &start, &end) == 2) { this_mapping = (start <= (uintptr_t)map && (uintptr_t)map < end); } else if (this_mapping && sscanf(line, "FilePmdMapped: %ld", &huge) == 1 && huge > 0) { return EXIT_SUCCESS; } } sleep(6); rewind(smaps_file); fflush(smaps_file); } } $ ./create_thp_file huge $ btrfs fi defrag -czstd ./huge Reviewed-by: Josef Bacik <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>

When I do fuzz test for bonding device interface, I got the following use-after-free Calltrace: ================================================================== BUG: KASAN: use-after-free in bond_enslave+0x1521/0x24f0 Read of size 8 at addr ffff88825bc11c00 by task ifenslave/7365 CPU: 5 PID: 7365 Comm: ifenslave Tainted: G E 5.15.0-rc1+ #13 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014 Call Trace: dump_stack_lvl+0x6c/0x8b print_address_description.constprop.0+0x48/0x70 kasan_report.cold+0x82/0xdb __asan_load8+0x69/0x90 bond_enslave+0x1521/0x24f0 bond_do_ioctl+0x3e0/0x450 dev_ifsioc+0x2ba/0x970 dev_ioctl+0x112/0x710 sock_do_ioctl+0x118/0x1b0 sock_ioctl+0x2e0/0x490 __x64_sys_ioctl+0x118/0x150 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f19159cf577 Code: b3 66 90 48 8b 05 11 89 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 78 RSP: 002b:00007ffeb3083c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffeb3084bca RCX: 00007f19159cf577 RDX: 00007ffeb3083ce0 RSI: 0000000000008990 RDI: 0000000000000003 RBP: 00007ffeb3084bc4 R08: 0000000000000040 R09: 0000000000000000 R10: 00007ffeb3084bc0 R11: 0000000000000246 R12: 00007ffeb3083ce0 R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffeb3083cb0 Allocated by task 7365: kasan_save_stack+0x23/0x50 __kasan_kmalloc+0x83/0xa0 kmem_cache_alloc_trace+0x22e/0x470 bond_enslave+0x2e1/0x24f0 bond_do_ioctl+0x3e0/0x450 dev_ifsioc+0x2ba/0x970 dev_ioctl+0x112/0x710 sock_do_ioctl+0x118/0x1b0 sock_ioctl+0x2e0/0x490 __x64_sys_ioctl+0x118/0x150 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae Freed by task 7365: kasan_save_stack+0x23/0x50 kasan_set_track+0x20/0x30 kasan_set_free_info+0x24/0x40 __kasan_slab_free+0xf2/0x130 kfree+0xd1/0x5c0 slave_kobj_release+0x61/0x90 kobject_put+0x102/0x180 bond_sysfs_slave_add+0x7a/0xa0 bond_enslave+0x11b6/0x24f0 bond_do_ioctl+0x3e0/0x450 dev_ifsioc+0x2ba/0x970 dev_ioctl+0x112/0x710 sock_do_ioctl+0x118/0x1b0 sock_ioctl+0x2e0/0x490 __x64_sys_ioctl+0x118/0x150 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae Last potentially related work creation: kasan_save_stack+0x23/0x50 kasan_record_aux_stack+0xb7/0xd0 insert_work+0x43/0x190 __queue_work+0x2e3/0x970 delayed_work_timer_fn+0x3e/0x50 call_timer_fn+0x148/0x470 run_timer_softirq+0x8a8/0xc50 __do_softirq+0x107/0x55f Second to last potentially related work creation: kasan_save_stack+0x23/0x50 kasan_record_aux_stack+0xb7/0xd0 insert_work+0x43/0x190 __queue_work+0x2e3/0x970 __queue_delayed_work+0x130/0x180 queue_delayed_work_on+0xa7/0xb0 bond_enslave+0xe25/0x24f0 bond_do_ioctl+0x3e0/0x450 dev_ifsioc+0x2ba/0x970 dev_ioctl+0x112/0x710 sock_do_ioctl+0x118/0x1b0 sock_ioctl+0x2e0/0x490 __x64_sys_ioctl+0x118/0x150 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae The buggy address belongs to the object at ffff88825bc11c00 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 0 bytes inside of 1024-byte region [ffff88825bc11c00, ffff88825bc12000) The buggy address belongs to the page: page:ffffea00096f0400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x25bc10 head:ffffea00096f0400 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x57ff00000010200(slab|head|node=1|zone=2|lastcpupid=0x7ff) raw: 057ff00000010200 ffffea0009a71c08 ffff888240001968 ffff88810004dbc0 raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88825bc11b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88825bc11b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff88825bc11c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88825bc11c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88825bc11d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Put new_slave in bond_sysfs_slave_add() will cause use-after-free problems when new_slave is accessed in the subsequent error handling process. Since new_slave will be put in the subsequent error handling process, remove the unnecessary put to fix it. In addition, when sysfs_create_file() fails, if some files have been crea- ted successfully, we need to call sysfs_remove_file() to remove them. Since there are sysfs_create_files() & sysfs_remove_files() can be used, use these two functions instead. Fixes: 7afcaec (bonding: use kobject_put instead of _del after kobject_add) Signed-off-by: Huang Guobin <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>

The exit function fixes a memory leak with the src field as detected by leak sanitizer. An example of which is: Indirect leak of 25133184 byte(s) in 207 object(s) allocated from: #0 0x7f199ecfe987 in __interceptor_calloc libsanitizer/asan/asan_malloc_linux.cpp:154 #1 0x55defe638224 in annotated_source__alloc_histograms util/annotate.c:803 #2 0x55defe6397e4 in symbol__hists util/annotate.c:952 #3 0x55defe639908 in symbol__inc_addr_samples util/annotate.c:968 #4 0x55defe63aa29 in hist_entry__inc_addr_samples util/annotate.c:1119 #5 0x55defe499a79 in hist_iter__report_callback tools/perf/builtin-report.c:182 #6 0x55defe7a859d in hist_entry_iter__add util/hist.c:1236 #7 0x55defe49aa63 in process_sample_event tools/perf/builtin-report.c:315 #8 0x55defe731bc8 in evlist__deliver_sample util/session.c:1473 #9 0x55defe731e38 in machines__deliver_event util/session.c:1510 #10 0x55defe732a23 in perf_session__deliver_event util/session.c:1590 #11 0x55defe72951e in ordered_events__deliver_event util/session.c:183 #12 0x55defe740082 in do_flush util/ordered-events.c:244 #13 0x55defe7407cb in __ordered_events__flush util/ordered-events.c:323 #14 0x55defe740a61 in ordered_events__flush util/ordered-events.c:341 #15 0x55defe73837f in __perf_session__process_events util/session.c:2390 #16 0x55defe7385ff in perf_session__process_events util/session.c:2420 ... Signed-off-by: Ian Rogers <[email protected]> Acked-by: Namhyung Kim <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: James Clark <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kajol Jain <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Martin Liška <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

…patch-fixes Cc: Davidlohr Bueso <[email protected]> WARNING: A patch subject line should describe the change not the tool that found it #2: Subject: kernel-sys-only-take-tasklist_lock-for-get-setpriorityprio_pgrp-checkpatch-fixes WARNING: Commit log lines starting with '#' are dropped by git as comments #5: #102: FILE: kernel/sys.c:321: WARNING: Possible unwrapped commit description (prefer a maximum 75 chars per line) #13: mechanically convert to the typical style using --fix or --fix-inplace. total: 0 errors, 3 warnings, 8 lines checked NOTE: For some of the reported defects, checkpatch may be able to mechanically convert to the typical style using --fix or --fix-inplace. ./patches/kernel-sys-only-take-tasklist_lock-for-get-setpriorityprio_pgrp-checkpatch-fixes.patch has style problems, please review. NOTE: If any of the errors are false positives, please report them to the maintainer, see CHECKPATCH in MAINTAINERS. Please run checkpatch prior to sending patches Cc: Davidlohr Bueso <[email protected]> Cc: Davidlohr Bueso <[email protected]> Cc: Oleg Nesterov <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Stephen Rothwell <[email protected]>

[ Upstream commit f9535d2 ] Similar to commit b8d8436 ("drm/i915/gt: Hold RPM wakelock during PXP suspend") but to fix the same warning for unbind during shutdown: ------------[ cut here ]------------ RPM wakelock ref not held during HW access WARNING: CPU: 0 PID: 4139 at drivers/gpu/drm/i915/intel_runtime_pm.h:115 gen12_fwtable_write32+0x1b7/0 Modules linked in: 8021q ccm rfcomm cmac algif_hash algif_skcipher af_alg uinput snd_hda_codec_hdmi vf industrialio iwl7000_mac80211 cros_ec_sensorhub lzo_rle lzo_compress zram iwlwifi cfg80211 joydev CPU: 0 PID: 4139 Comm: halt Tainted: G U W 5.10.84 grate-driver#13 344e11e079c4a03940d949e537eab645f6 RIP: 0010:gen12_fwtable_write32+0x1b7/0x200 Code: 48 c7 c7 fc b3 b5 89 31 c0 e8 2c f3 ad ff 0f 0b e9 04 ff ff ff c6 05 71 e9 1d 01 01 48 c7 c7 d67 RSP: 0018:ffffa09ec0bb3bb0 EFLAGS: 00010246 RAX: 12dde97bbd260300 RBX: 00000000000320f0 RCX: ffffffff89e60ea0 RDX: 0000000000000000 RSI: 00000000ffffdfff RDI: ffffffff89e60e70 RBP: ffffa09ec0bb3bd8 R08: 0000000000000000 R09: ffffa09ec0bb3950 R10: 00000000ffffdfff R11: ffffffff89e91160 R12: 0000000000000000 R13: 0000000028121969 R14: ffff9515c32f0990 R15: 0000000040000000 FS: 0000790dcf225740(0000) GS:ffff951737800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000058b25efae147 CR3: 0000000133ea6001 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: intel_pxp_fini_hw+0x2f/0x39 i915_pxp_tee_component_unbind+0x1c/0x42 component_unbind+0x32/0x48 component_unbind_all+0x80/0x9d take_down_master+0x24/0x36 component_master_del+0x56/0x70 mei_pxp_remove+0x2c/0x68 mei_cl_device_remove+0x35/0x68 device_release_driver_internal+0x100/0x1a1 mei_cl_bus_remove_device+0x21/0x79 mei_cl_bus_remove_devices+0x3b/0x51 mei_stop+0x3b/0xae mei_me_shutdown+0x23/0x58 device_shutdown+0x144/0x1d3 kernel_power_off+0x13/0x4c __se_sys_reboot+0x1d4/0x1e9 do_syscall_64+0x43/0x55 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x790dcf316273 Code: 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 89 fa be 69 19 12 28 bf ad8 RSP: 002b:00007ffca0df9198 EFLAGS: 00000202 ORIG_RAX: 00000000000000a9 RAX: ffffffffffffffda RBX: 000000004321fedc RCX: 0000790dcf316273 RDX: 000000004321fedc RSI: 0000000028121969 RDI: 00000000fee1dead RBP: 00007ffca0df9200 R08: 0000000000000007 R09: 0000563ce8cd8970 R10: 0000000000000000 R11: 0000000000000202 R12: 00007ffca0df9308 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000003 ---[ end trace 2f501b01b348f114 ]--- ACPI: Preparing to enter system sleep state S5 reboot: Power down Changes since v1: - Rebase to latest drm-tip Fixes: 0cfab4c ("drm/i915/pxp: Enable PXP power management") Suggested-by: Lee Shawn C <[email protected]> Signed-off-by: Juston Li <[email protected]> Reviewed-by: Daniele Ceraolo Spurio <[email protected]> Signed-off-by: John Harrison <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 57ded5f) Signed-off-by: Tvrtko Ursulin <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

While booting secondary CPUs, cpus_read_[lock/unlock] is not keeping online cpumask stable. The transient online mask results in below calltrace. [ 0.324121] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.346652] Detected PIPT I-cache on CPU2 [ 0.347212] CPU2: Booted secondary processor 0x0000000002 [0x410fd083] [ 0.377255] Detected PIPT I-cache on CPU3 [ 0.377823] CPU3: Booted secondary processor 0x0000000003 [0x410fd083] [ 0.379040] ------------[ cut here ]------------ [ 0.383662] WARNING: CPU: 0 PID: 10 at kernel/workqueue.c:3084 __flush_work+0x12c/0x138 [ 0.384850] Modules linked in: [ 0.385403] CPU: 0 PID: 10 Comm: rcu_tasks_rude_ Not tainted 5.17.0-rc3-v8+ grate-driver#13 [ 0.386473] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT) [ 0.387289] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.388308] pc : __flush_work+0x12c/0x138 [ 0.388970] lr : __flush_work+0x80/0x138 [ 0.389620] sp : ffffffc00aaf3c60 [ 0.390139] x29: ffffffc00aaf3d20 x28: ffffffc009c16af0 x27: ffffff80f761df48 [ 0.391316] x26: 0000000000000004 x25: 0000000000000003 x24: 0000000000000100 [ 0.392493] x23: ffffffffffffffff x22: ffffffc009c16b10 x21: ffffffc009c16b28 [ 0.393668] x20: ffffffc009e53861 x19: ffffff80f77fbf40 x18: 00000000d744fcc9 [ 0.394842] x17: 000000000000000b x16: 00000000000001c2 x15: ffffffc009e57550 [ 0.396016] x14: 0000000000000000 x13: ffffffffffffffff x12: 0000000100000000 [ 0.397190] x11: 0000000000000462 x10: ffffff8040258008 x9 : 0000000100000000 [ 0.398364] x8 : 0000000000000000 x7 : ffffffc0093c8bf4 x6 : 0000000000000000 [ 0.399538] x5 : 0000000000000000 x4 : ffffffc00a976e40 x3 : ffffffc00810444c [ 0.400711] x2 : 0000000000000004 x1 : 0000000000000000 x0 : 0000000000000000 [ 0.401886] Call trace: [ 0.402309] __flush_work+0x12c/0x138 [ 0.402941] schedule_on_each_cpu+0x228/0x278 [ 0.403693] rcu_tasks_rude_wait_gp+0x130/0x144 [ 0.404502] rcu_tasks_kthread+0x220/0x254 [ 0.405264] kthread+0x174/0x1ac [ 0.405837] ret_from_fork+0x10/0x20 [ 0.406456] irq event stamp: 102 [ 0.406966] hardirqs last enabled at (101): [<ffffffc0093c8468>] _raw_spin_unlock_irq+0x78/0xb4 [ 0.408304] hardirqs last disabled at (102): [<ffffffc0093b8270>] el1_dbg+0x24/0x5c [ 0.409410] softirqs last enabled at (54): [<ffffffc0081b80c8>] local_bh_enable+0xc/0x2c [ 0.410645] softirqs last disabled at (50): [<ffffffc0081b809c>] local_bh_disable+0xc/0x2c [ 0.411890] ---[ end trace 0000000000000000 ]--- [ 0.413000] smp: Brought up 1 node, 4 CPUs [ 0.413762] SMP: Total of 4 processors activated. [ 0.414566] CPU features: detected: 32-bit EL0 Support [ 0.415414] CPU features: detected: 32-bit EL1 Support [ 0.416278] CPU features: detected: CRC32 instructions [ 0.447021] Callback from call_rcu_tasks_rude() invoked. [ 0.506693] Callback from call_rcu_tasks() invoked. This commit therefore fixes this issue by applying a single-CPU optimization to the RCU Tasks Rude grace-period process. The key point here is that the purpose of this RCU flavor is to force a schedule on each online CPU since some past event. But the rcu_tasks_rude_wait_gp() function runs in the context of the RCU Tasks Rude's grace-period kthread, so there must already have been a context switch on the current CPU since the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude(). So if there is only a single CPU online, RCU Tasks Rude's grace-period kthread does not need to anything at all. It turns out that the rcu_tasks_rude_wait_gp() function's call to schedule_on_each_cpu() causes problems during early boot. During that time, there is only one online CPU, namely the boot CPU. Therefore, applying this single-CPU optimization fixes early-boot instances of this problem. Link: https://lore.kernel.org/lkml/[email protected]/T/ Suggested-by: Paul E. McKenney <[email protected]> Signed-off-by: Padmanabha Srinivasaiah <[email protected]> Signed-off-by: Paul E. McKenney <[email protected]>

[ Upstream commit 99d4850 ] Found by leak sanitizer: ``` ==1632594==ERROR: LeakSanitizer: detected memory leaks Direct leak of 21 byte(s) in 1 object(s) allocated from: #0 0x7f2953a7077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439 #1 0x556701d6fbbf in perf_env__read_cpuid util/env.c:369 #2 0x556701d70589 in perf_env__cpuid util/env.c:465 #3 0x55670204bba2 in x86__is_amd_cpu arch/x86/util/env.c:14 #4 0x5567020487a2 in arch__post_evsel_config arch/x86/util/evsel.c:83 #5 0x556701d8f78b in evsel__config util/evsel.c:1366 #6 0x556701ef5872 in evlist__config util/record.c:108 #7 0x556701cd6bcd in test__PERF_RECORD tests/perf-record.c:112 #8 0x556701cacd07 in run_test tests/builtin-test.c:236 grate-driver#9 0x556701cacfac in test_and_print tests/builtin-test.c:265 grate-driver#10 0x556701cadddb in __cmd_test tests/builtin-test.c:402 grate-driver#11 0x556701caf2aa in cmd_test tests/builtin-test.c:559 grate-driver#12 0x556701d3b557 in run_builtin tools/perf/perf.c:323 grate-driver#13 0x556701d3bac8 in handle_internal_command tools/perf/perf.c:377 grate-driver#14 0x556701d3be90 in run_argv tools/perf/perf.c:421 grate-driver#15 0x556701d3c3f8 in main tools/perf/perf.c:537 grate-driver#16 0x7f2952a46189 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 SUMMARY: AddressSanitizer: 21 byte(s) leaked in 1 allocation(s). ``` Fixes: f7b58cb ("perf mem/c2c: Add load store event mappings for AMD") Signed-off-by: Ian Rogers <[email protected]> Acked-by: Ravi Bangoria <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit ede72dc ] Fuzzing found that an invalid tracepoint name would create a memory leak with an address sanitizer build: ``` $ perf stat -e '*:o/' true event syntax error: '*:o/' \___ parser error Run 'perf list' for a list of valid events Usage: perf stat [<options>] [<command>] -e, --event <event> event selector. use 'perf list' to list available events ================================================================= ==59380==ERROR: LeakSanitizer: detected memory leaks Direct leak of 4 byte(s) in 2 object(s) allocated from: #0 0x7f38ac07077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439 #1 0x55f2f41be73b in str util/parse-events.l:49 #2 0x55f2f41d08e8 in parse_events_lex util/parse-events.l:338 #3 0x55f2f41dc3b1 in parse_events_parse util/parse-events-bison.c:1464 #4 0x55f2f410b8b3 in parse_events__scanner util/parse-events.c:1822 #5 0x55f2f410d1b9 in __parse_events util/parse-events.c:2094 #6 0x55f2f410e57f in parse_events_option util/parse-events.c:2279 #7 0x55f2f4427b56 in get_value tools/lib/subcmd/parse-options.c:251 #8 0x55f2f4428d98 in parse_short_opt tools/lib/subcmd/parse-options.c:351 grate-driver#9 0x55f2f4429d80 in parse_options_step tools/lib/subcmd/parse-options.c:539 grate-driver#10 0x55f2f442acb9 in parse_options_subcommand tools/lib/subcmd/parse-options.c:654 grate-driver#11 0x55f2f3ec99fc in cmd_stat tools/perf/builtin-stat.c:2501 grate-driver#12 0x55f2f4093289 in run_builtin tools/perf/perf.c:322 grate-driver#13 0x55f2f40937f5 in handle_internal_command tools/perf/perf.c:375 grate-driver#14 0x55f2f4093bbd in run_argv tools/perf/perf.c:419 grate-driver#15 0x55f2f409412b in main tools/perf/perf.c:535 SUMMARY: AddressSanitizer: 4 byte(s) leaked in 2 allocation(s). ``` Fix by adding the missing destructor. Fixes: 865582c ("perf tools: Adds the tracepoint name parsing support") Signed-off-by: Ian Rogers <[email protected]> Cc: He Kuang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Namhyung Kim <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit e3e82fc ] When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be dereferenced as wrong struct in irdma_free_pending_cqp_request(). PID: 3669 TASK: ffff88aef892c000 CPU: 28 COMMAND: "kworker/28:0" #0 [fffffe0000549e38] crash_nmi_callback at ffffffff810e3a34 #1 [fffffe0000549e40] nmi_handle at ffffffff810788b2 #2 [fffffe0000549ea0] default_do_nmi at ffffffff8107938f #3 [fffffe0000549eb8] do_nmi at ffffffff81079582 #4 [fffffe0000549ef0] end_repeat_nmi at ffffffff82e016b4 [exception RIP: native_queued_spin_lock_slowpath+1291] RIP: ffffffff8127e72b RSP: ffff88aa841ef778 RFLAGS: 00000046 RAX: 0000000000000000 RBX: ffff88b01f849700 RCX: ffffffff8127e47e RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff83857ec0 RBP: ffff88afe3e4efc8 R8: ffffed15fc7c9dfa R9: ffffed15fc7c9dfa R10: 0000000000000001 R11: ffffed15fc7c9df9 R12: 0000000000740000 R13: ffff88b01f849708 R14: 0000000000000003 R15: ffffed1603f092e1 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 -- <NMI exception stack> -- #5 [ffff88aa841ef778] native_queued_spin_lock_slowpath at ffffffff8127e72b #6 [ffff88aa841ef7b0] _raw_spin_lock_irqsave at ffffffff82c22aa4 #7 [ffff88aa841ef7c8] __wake_up_common_lock at ffffffff81257363 #8 [ffff88aa841ef888] irdma_free_pending_cqp_request at ffffffffa0ba12cc [irdma] grate-driver#9 [ffff88aa841ef958] irdma_cleanup_pending_cqp_op at ffffffffa0ba1469 [irdma] grate-driver#10 [ffff88aa841ef9c0] irdma_ctrl_deinit_hw at ffffffffa0b2989f [irdma] grate-driver#11 [ffff88aa841efa28] irdma_remove at ffffffffa0b252df [irdma] grate-driver#12 [ffff88aa841efae8] auxiliary_bus_remove at ffffffff8219afdb grate-driver#13 [ffff88aa841efb00] device_release_driver_internal at ffffffff821882e6 grate-driver#14 [ffff88aa841efb38] bus_remove_device at ffffffff82184278 grate-driver#15 [ffff88aa841efb88] device_del at ffffffff82179d23 grate-driver#16 [ffff88aa841efc48] ice_unplug_aux_dev at ffffffffa0eb1c14 [ice] grate-driver#17 [ffff88aa841efc68] ice_service_task at ffffffffa0d88201 [ice] grate-driver#18 [ffff88aa841efde8] process_one_work at ffffffff811c589a grate-driver#19 [ffff88aa841efe60] worker_thread at ffffffff811c71ff grate-driver#20 [ffff88aa841eff10] kthread at ffffffff811d87a0 grate-driver#21 [ffff88aa841eff50] ret_from_fork at ffffffff82e0022f Fixes: 44d9e52 ("RDMA/irdma: Implement device initialization definitions") Link: https://lore.kernel.org/r/[email protected] Suggested-by: "Ismail, Mustafa" <[email protected]> Signed-off-by: Shifeng Li <[email protected]> Reviewed-by: Shiraz Saleem <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[SQUASH] WIP: ARM: tegra: Add device-tree for ASUS Transformer Prime …

6e71dbd

…TF201 Add device-tree for ASUS Transformer Prime TF201, which is NVIDIA Tegra30-based tablet device. Signed-off-by: Svyatoslav Ryhel <[email protected]> Signed-off-by: Ion Agorria <[email protected]>

digetx reviewed Dec 10, 2020

View reviewed changes

arch/arm/boot/dts/tegra30-asus-tf201.dts Show resolved Hide resolved

digetx merged commit 47d7e48 into grate-driver:master Dec 10, 2020

clamor-s deleted the squash branch December 11, 2020 12:39

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

ARM: tegra: Add device-tree for ASUS Transformer Prime TF201 #13

ARM: tegra: Add device-tree for ASUS Transformer Prime TF201 #13

clamor-s commented Dec 10, 2020 •

edited

Loading

digetx left a comment

clamor-s commented Dec 11, 2020 •

edited

Loading

digetx commented Dec 12, 2020

clamor-s commented Dec 12, 2020 •

edited

Loading

digetx commented Dec 13, 2020

ARM: tegra: Add device-tree for ASUS Transformer Prime TF201 #13

ARM: tegra: Add device-tree for ASUS Transformer Prime TF201 #13

Conversation

clamor-s commented Dec 10, 2020 • edited Loading

digetx left a comment

Choose a reason for hiding this comment

clamor-s commented Dec 11, 2020 • edited Loading

digetx commented Dec 12, 2020

clamor-s commented Dec 12, 2020 • edited Loading

digetx commented Dec 13, 2020

clamor-s commented Dec 10, 2020 •

edited

Loading

clamor-s commented Dec 11, 2020 •

edited

Loading

clamor-s commented Dec 12, 2020 •

edited

Loading