AMRC Connectivity Stack

The AMRC Connectivity Stack (ACS) is a Kubernetes Helm chart that contains a comprehensive set of open-source services developed by the AMRC that enables an end-to-end implementation of the Factory+ framework.

Prerequisites

Ensure that you familiarise yourself with the concepts of both Kubernetes and Factory+ before continuing. This chart installs a full end-to-end deployment of Factory+ onto a Kubernetes cluster and there are a lot of moving parts.

Known Limitations

Although Factory+ and ACS fully supports edge-based Cell Gateways, this chart does not support the deployment of edge-based Cell Gateways located on other Kubernetes Clusters, which is recommended in production. This is due to the fact that the chart deploys manifests to Cell Gateways, which requires the nodes to be on the same cluster. We already have a proof-of-concept implementation of how to address this and we aim to update this Helm chart in the near future to support.

Get Started

This chart can be installed onto a local Kubernetes cluster for development or testing by following the instructions below. For production deployments, please refer to the production deployment guide.

Install Helm

Helm is a package manager for Kubernetes that allows you to easily install and manage applications on Kubernetes. It must be installed on the machine that you'll be using to deploy ACS from. To install Helm, follow the instructions here.

Install Kubectl

Kubectl is a command-line tool for controlling Kubernetes clusters. It must be installed on the machine that you'll be using to deploy ACS from. To install Kubectl, follow the instructions here.

Install Minikube

Minikube is a tool that allows you to run a local Kubernetes cluster on your machine. It is not required to deploy ACS, but it is recommended for development and testing. To install Minikube, follow the instructions here. If you do not wish to use Minikube, you can deploy ACS to any Kubernetes cluster.

Verify Installation

To verify that Helm and Kubectl have been installed correctly, run the following commands:

helm version
kubectl version
minikube version

Next, create a new MiniKube cluster by running the following command:

minikube start

To verify that you can connect to your MiniKube cluster, run the following command:

kubectl cluster-info

Configure Base URL

This Chart creates a load balancer on your Kubernetes cluster that exposes all services at various subdomain. Please ensure that you have a wildcard DNS entry configured to direct all *.<baseURL> requests to your local kube cluster. For example, if you set baseUrl to localhost, you should have a DNS entry that directs all *.localhost requests to your local kube cluster on ports 80 and/or 443 (depending on whether you have enabled secure and want to serve ACS over HTTPS).

Install ACS

Now it's time to install the AMRC Connectivity Stack. It's recommended that you utilise a tool like Lens to view the cluster status as it bootstraps to ensure that everything is working as expected. Lens can be downloaded here.

First, add the AMRC Factory+ Helm repository:

helm repo add amrc-connectivity-stack https://amrc-factoryplus.github.io/amrc-connectivity-stack/build
helm repo update

Next, create a values.yaml file in a sensible location on your local machine. This file will be used to configure the deployment and can contain many options for customisation and configuration (see values for more information). At the very least, you should set the following values:

acs:
  baseUrl: localhost # Set this to the domain that ACS will be served from. Localhost should suffice for development.
  organisation: AMRC # Set this to the name of your organisation. It will be used across the deployment for branding and naming.
  secure: false # Set this to true if you want to serve ACS over HTTPS. This is recommended for production deployments but can be turned for development.
  tlsSecretName: factoryplus-tls # Set this to the name of the secret containing the wildcard certificate for the above domain. This is only required if secure is set to true.
identity:
  realm: LOCALHOST # Set the identity realm for the deployment. This is used to namespace the identity server and should be unique to your deployment. It is recommended that you use the domain name in capitals for this value.

Before we install, we need to create the factory-plus namespace, which is where all ACS services will be deployed to. If a different namespace is chosen by changing the -n <namespace> on the helm install command then ensure the namespace exists before installing ACS.

To create the factory-plus namespace, run the following command:

kubectl create namespace factory-plus

Finally, install ACS by running the following command.

helm install acs amrc-connectivity-stack/amrc-connectivity-stack -f values.yaml --namespace factory-plus

Alternatively, the values can be supplied directly to the helm install command:

helm install acs amrc-connectivity-stack/amrc-connectivity-stack --set acs.baseUrl=localhost --set acs.organisation=AMRC --set acs.secure=false --namespace factory-plus

If all went to plan you should now have a fully functioning ACS deployment beginning to deploy to your local Kubernetes cluster. Note that it can take a few minutes to have all services operational.

Take note of the service URLs printed at the end of the installation. You will need these to connect to the various services.

Verifying Installation

Get the password for the admin user by running the following command. Note that it may not return the password until the deployment has finished bootstrapping.

echo $(sudo kubectl get secret krb5-passwords -o jsonpath="{.data.admin}" -n {{.Release.Namespace}} | base64 --decode)

Once you have the admin password you can connect to the MQTT broker at the URL supplied to you and subscribe to spBv1.0/#. It's advisable to do this before you start adding devices to the system so that you can see all traffic. MQTTExplorer is a good tool for this and can be downloaded here, however building the tool from this pull request may be more useful when working with ACS and Sparkplug messages.

Next, log into the manager at the URL supplied to you as the admin user and create a Group, Node (Soft Gateway) and Device. Configure the device by completing the Information, Connection, and Schema tabs until you see a green VALID tag in the top right corner. Once you've configured the device you should see MQTT traffic begin to flow.

Finally, get the admin password for InfluxDB by running the following command and log into the InfluxDB instance as the admin user at at the URL supplied to you.

echo $(sudo kubectl get secret acs-influxdb2-auth -o jsonpath="{.data.admin-password}" -n {{.Release.Namespace}} | base64 --decode)

Production Deployment

Production deployment does not differ greatly from development deployment, however there are a few things to note:

• Ensure that you have a wildcard DNS entry configured to direct all *. requests to the load balancer.
• Ensure that you have a wildcard TLS certificate for the domain specified in baseUrl
• Ensure that secure is set to true
• Only use admin user for disaster recovery

Maintainers

Name	Email
Alex Godbehere	[email protected]
Ben Morrow	[email protected]

Requirements

Repository	Name	Version
https://alexgodbehere.github.io/helm-repository	operator	5.0.4
https://bitnami-labs.github.io/sealed-secrets/	sealed-secrets	2.8.1
https://grafana.github.io/helm-charts	grafana	6.52.4
https://grafana.github.io/helm-charts	loki	4.8.0
https://grafana.github.io/helm-charts	promtail	6.9.3
https://helm.influxdata.com/	influxdb2	2.1.1
https://helm.traefik.io/traefik	traefik	10.19.*
https://operator.min.io	tenant	5.0.3

Values

Key	Type	Default	Description
acs.baseUrl	string	"localhost"	The base URL that services will be served from
acs.organisation	string	"AMRC"	The organisation where ACS is being deployed
acs.secure	bool	true	Whether or not services should be served over HTTPS
acs.tlsSecretName	string	"factoryplus-tls"	The name of the secret holding the wildcard certificate for the above domain.
auth.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Authorisation component
auth.image.repository	string	"acs-auth"	The repository of the Authorisation component
auth.image.tag	string	"latest"	The tag of the Authorisation component
cmdesc.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Commands component
cmdesc.image.repository	string	"acs-cmdesc"	The repository of the Commands component
cmdesc.image.tag	string	"latest"	The tag of the Commands component
cmdesc.verbosity	int	1	Possible values are either 1 to enable all possible debugging, or a comma-separated list of debug tags (the tags printed before the log lines). No logging is specified as an empty string.
configdb.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Configuration Store component
configdb.image.repository	string	"acs-configdb"	The repository of the Configuration Store component
configdb.image.tag	string	"latest"	The tag of the Configuration Store component
directory.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Directory component
directory.image.repository	string	"acs-directory"	The repository of the Directory component
directory.image.tag	string	"latest"	The tag of the Directory component
identity.identity.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Identity component
identity.identity.image.repository	string	"acs-identity"	The repository of the Identity component
identity.identity.image.tag	string	"latest"	The tag of the Identity component
identity.krbKeysOperator.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the KerberosKey Operator
identity.krbKeysOperator.image.repository	string	"acs-krb-keys-operator"	The repository of the KerberosKey Operator
identity.krbKeysOperator.image.tag	string	"latest"	The tag of the KerberosKey Operator
identity.realm	string	"LOCALHOST"	The Kerberos realm for this Factory+ deployment.
manager.debug	bool	false	Whether debug mode is enabled. DO NOT USE THIS IN PRODUCTION.
manager.edge.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Edge Agent component
manager.edge.repository	string	"acs-edge"	The repository of the Edge Agent component
manager.edge.tag	string	"latest"	The tag of the Edge Agent component
manager.env	string	"production"	The environment that the manager is running in
manager.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Manager component
manager.image.repository	string	"acs-manager"	The repository of the Manager component
manager.image.tag	string	"latest"	The tag of the Manager component
manager.logLevel	string	"warning"	The minimum log level that the manager will log messages at
manager.meilisearch.key	string	"masterKey"	The key that the manager uses to connect to the Meilisearch search engine
manager.name	string	"Factory+ Manager"	A string used to customise the branding of the manager
minio.exposeConsole	bool	false	Whether or not to expose the MinIO console outside of the cluster
mqtt.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the MQTT component
mqtt.image.repository	string	"acs-mqtt"	The repository of the MQTT component
mqtt.image.tag	string	"latest"	The tag of the MQTT component
warehouse.ingester.image.registry	string	"ghcr.io/amrc-factoryplus"	The registry of the Commands component
warehouse.ingester.image.repository	string	"influxdb-sparkplug-ingester"	The repository of the Commands component
warehouse.ingester.image.tag	string	"latest"	The tag of the Commands component

---