✨ SAMD21 HAL / Minitronics v2.0 (MarlinFirmware#24976)

.github/workflows/test-builds.yml

@@ -44,6 +44,7 @@ jobs:
         - teensy31
         - teensy35
         - teensy41
+        - SAMD21_minitronics20
         - SAMD51_grandcentral_m4
         - PANDA_PI_V29
 

Marlin/Configuration.h

@@ -2805,7 +2805,7 @@ ABL:        BLTouch Zmax
 
 //
 // ReprapWorld Graphical LCD
-// https://reprapworld.com/?products_details&products_id/1218
+// https://reprapworld.com/electronics/3d-printer-modules/autonomous-printing/graphical-lcd-screen-v1-0/
 //
 //#define REPRAPWORLD_GRAPHICAL_LCD
 

Marlin/src/HAL/NATIVE_SIM/u8g/u8g_com_st7920_sw_spi.cpp

@@ -168,4 +168,4 @@ uint8_t u8g_com_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
 #endif
 
 #endif // IS_U8GLIB_ST7920
-#endif // TARGET_LPC1768
+#endif // __PLAT_NATIVE_SIM__

Marlin/src/HAL/SAMD21/HAL.cpp

@@ -0,0 +1,212 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * SAMD21 HAL developed by Bart Meijer (brupje)
+ * Based on SAMD51 HAL by Giuliano Zaro (AKA GMagician)
+ */
+#ifdef __SAMD21__
+
+#include "../../inc/MarlinConfig.h"
+
+#include <wiring_private.h>
+
+#if USING_HW_SERIALUSB
+  DefaultSerial1 MSerialUSB(false, SerialUSB);
+#endif
+#if USING_HW_SERIAL0
+  DefaultSerial2 MSerial1(false, Serial1);
+#endif
+#if USING_HW_SERIAL1
+  DefaultSerial3 MSerial2(false, Serial2);
+#endif
+
+
+
+#define WDT_CONFIG_PER_7_Val 0x9u
+#define WDT_CONFIG_PER_Pos 0
+#define WDT_CONFIG_PER_7 (WDT_CONFIG_PER_7_Val << WDT_CONFIG_PER_Pos)
+
+#if ENABLED(USE_WATCHDOG)
+
+  #define WDT_TIMEOUT_REG TERN(WATCHDOG_DURATION_8S, WDT_CONFIG_PER_CYC8192, WDT_CONFIG_PER_CYC4096) // 4 or 8 second timeout
+
+  void MarlinHAL::watchdog_init() {
+       // Set up the generic clock (GCLK2) used to clock the watchdog timer at 1.024kHz
+    GCLK->GENDIV.reg = GCLK_GENDIV_DIV(4) |            // Divide the 32.768kHz clock source by divisor 32, where 2^(4 + 1): 32.768kHz/32=1.024kHz
+                      GCLK_GENDIV_ID(2);              // Select Generic Clock (GCLK) 2
+    while (GCLK->STATUS.bit.SYNCBUSY);                // Wait for synchronization
+
+    REG_GCLK_GENCTRL =  GCLK_GENCTRL_DIVSEL |         // Set to divide by 2^(GCLK_GENDIV_DIV(4) + 1)
+                        GCLK_GENCTRL_IDC |            // Set the duty cycle to 50/50 HIGH/LOW
+                        GCLK_GENCTRL_GENEN |          // Enable GCLK2
+                        GCLK_GENCTRL_SRC_OSCULP32K |  // Set the clock source to the ultra low power oscillator (OSCULP32K)
+                        GCLK_GENCTRL_ID(2);           // Select GCLK2
+    while (GCLK->STATUS.bit.SYNCBUSY);                // Wait for synchronization
+
+    // Feed GCLK2 to WDT (Watchdog Timer)
+    REG_GCLK_CLKCTRL =  GCLK_CLKCTRL_CLKEN |          // Enable GCLK2 to the WDT
+                        GCLK_CLKCTRL_GEN_GCLK2 |      // Select GCLK2
+                        GCLK_CLKCTRL_ID_WDT;          // Feed the GCLK2 to the WDT
+    while (GCLK->STATUS.bit.SYNCBUSY);                // Wait for synchronization
+
+    WDT->CONFIG.bit.PER = WDT_CONFIG_PER_7;                // Set the WDT reset timeout to 4 seconds
+    while (WDT->STATUS.bit.SYNCBUSY);                 // Wait for synchronization
+    REG_WDT_CTRL = WDT_CTRL_ENABLE;                   // Enable the WDT in normal mode
+    while (WDT->STATUS.bit.SYNCBUSY);                 // Wait for synchronization
+  }
+
+  // Reset watchdog. MUST be called at least every 4 seconds after the
+  // first watchdog_init or SAMD will go into emergency procedures.
+  void MarlinHAL::watchdog_refresh() {
+    WDT->CLEAR.reg = WDT_CLEAR_CLEAR_KEY;
+    while (WDT->STATUS.bit.SYNCBUSY);
+  }
+
+#endif
+
+// ------------------------
+// Types
+// ------------------------
+
+// ------------------------
+// Private Variables
+// ------------------------
+
+// ------------------------
+// Private functions
+// ------------------------
+
+void MarlinHAL::dma_init() {}
+
+// ------------------------
+// Public functions
+// ------------------------
+
+// HAL initialization task
+void MarlinHAL::init() {
+  TERN_(DMA_IS_REQUIRED, dma_init());
+  #if ENABLED(SDSUPPORT)
+    #if HAS_SD_DETECT && SD_CONNECTION_IS(ONBOARD)
+      SET_INPUT_PULLUP(SD_DETECT_PIN);
+    #endif
+    OUT_WRITE(SDSS, HIGH);  // Try to set SDSS inactive before any other SPI users start up
+  #endif
+}
+
+#pragma push_macro("WDT")
+#undef WDT    // Required to be able to use '.bit.WDT'. Compiler wrongly replace struct field with WDT define
+uint8_t MarlinHAL::get_reset_source() {
+
+  return 0;
+}
+#pragma pop_macro("WDT")
+
+void MarlinHAL::reboot() { NVIC_SystemReset(); }
+
+extern "C" {
+  void * _sbrk(int incr);
+  extern unsigned int __bss_end__; // end of bss section
+}
+
+// Return free memory between end of heap (or end bss) and whatever is current
+int freeMemory() {
+  int free_memory, heap_end = (int)_sbrk(0);
+  return (int)&free_memory - (heap_end ?: (int)&__bss_end__);
+}
+
+// ------------------------
+// ADC
+// ------------------------
+
+uint16_t MarlinHAL::adc_result;
+
+void MarlinHAL::adc_init() {
+  /* thanks to https://www.eevblog.com/forum/microcontrollers/samd21g18-adc-with-resrdy-interrupts-only-reads-once-or-twice/ */
+
+  ADC->CTRLA.bit.ENABLE = false;
+  while(ADC->STATUS.bit.SYNCBUSY);
+
+  // load chip corrections
+  uint32_t bias = (*((uint32_t *) ADC_FUSES_BIASCAL_ADDR) & ADC_FUSES_BIASCAL_Msk) >> ADC_FUSES_BIASCAL_Pos;
+  uint32_t linearity = (*((uint32_t *) ADC_FUSES_LINEARITY_0_ADDR) & ADC_FUSES_LINEARITY_0_Msk) >> ADC_FUSES_LINEARITY_0_Pos;
+  linearity |= ((*((uint32_t *) ADC_FUSES_LINEARITY_1_ADDR) & ADC_FUSES_LINEARITY_1_Msk) >> ADC_FUSES_LINEARITY_1_Pos) << 5;
+
+  /* Wait for bus synchronization. */
+  while (ADC->STATUS.bit.SYNCBUSY) {};
+
+  ADC->CALIB.reg = ADC_CALIB_BIAS_CAL(bias) | ADC_CALIB_LINEARITY_CAL(linearity);
+
+  /* Wait for bus synchronization. */
+  while (ADC->STATUS.bit.SYNCBUSY) {};
+
+  ADC->CTRLA.bit.SWRST = true;
+  while(ADC->STATUS.bit.SYNCBUSY);
+
+  ADC->REFCTRL.reg = ADC_REFCTRL_REFSEL_INTVCC1;
+  ADC->AVGCTRL.reg = ADC_AVGCTRL_SAMPLENUM_32| ADC_AVGCTRL_ADJRES(4);;
+
+
+  ADC->CTRLB.reg = ADC_CTRLB_PRESCALER_DIV128 |
+                 ADC_CTRLB_RESSEL_16BIT |
+                 ADC_CTRLB_FREERUN;
+  while(ADC->STATUS.bit.SYNCBUSY);
+
+  ADC->SAMPCTRL.bit.SAMPLEN = 0x00;
+  while(ADC->STATUS.bit.SYNCBUSY);
+
+  ADC->INPUTCTRL.reg =  ADC_INPUTCTRL_INPUTSCAN(HAL_ADC_AIN_LEN) // scan  (INPUTSCAN + NUM_EXTUDERS - 1) pins
+  | ADC_INPUTCTRL_GAIN_DIV2  |ADC_INPUTCTRL_MUXNEG_GND| HAL_ADC_AIN_START ;  /* set to first AIN */
+
+  while(ADC->STATUS.bit.SYNCBUSY);
+
+  ADC->INTENSET.reg |= ADC_INTENSET_RESRDY; // enable Result Ready ADC interrupts
+  while (ADC->STATUS.bit.SYNCBUSY);
+
+  NVIC_EnableIRQ(ADC_IRQn); // enable ADC interrupts
+
+  NVIC_SetPriority(ADC_IRQn, 3);
+
+  ADC->CTRLA.bit.ENABLE = true;
+}
+
+volatile uint32_t adc_results[HAL_ADC_AIN_NUM_SENSORS];
+
+void ADC_Handler() {
+  while(ADC->STATUS.bit.SYNCBUSY == 1);
+  int pos = ADC->INPUTCTRL.bit.INPUTOFFSET;
+
+  adc_results[pos] = ADC->RESULT.reg; /* Read the value. */
+  ADC->INTFLAG.reg = ADC_INTENSET_RESRDY; /* Clear the data ready flag. */
+}
+
+void MarlinHAL::adc_start(const pin_t pin) {
+  /* due to the way INPUTOFFSET works, the last sensor is the first position in the array
+    and we want the ADC_handler interrupt to be as simple possible, so we do the calculation here.
+  */
+  unsigned int pos = PIN_TO_INPUTCTRL(pin) - HAL_ADC_AIN_START + 1;
+  if (pos == HAL_ADC_AIN_NUM_SENSORS) pos = 0;
+  adc_result = adc_results[pos]; // 16-bit resolution
+  //adc_result = 0xFFFF;
+}
+
+#endif // __SAMD21__