-- mode: Outline --
This is version 1.0 of the unwind library. This library supports several architecture/operating-system combinations:
Linux/x86-64: Works well. Linux/x86: Works well. Linux/ARM: Works well. Linux/IA-64: Fully tested and supported. Linux/PARISC: Works well, but C library missing unwind-info. HP-UX/IA-64: Mostly works but known to have some serious limitations. MIPS: Newly added. Linux/AArch64: Newly added. Linux/PPC64: Newly added. Linux/SuperH: Newly added. FreeBSD/i386: Newly added. FreeBSD/x86-64: Newly added (FreeBSD architecture is known as amd64). Linux/Tilegx: Newly added (64-bit mode only).
- General Build Instructions
In general, this library can be built and installed with the following commands:
$ ./autogen.sh # Needed only for building from git. Depends on libtool.
$ ./configure
$ make
$ make install prefix=PREFIX
where PREFIX is the installation prefix. By default, a prefix of /usr/local is used, such that libunwind.a is installed in /usr/local/lib and unwind.h is installed in /usr/local/include. For testing, you may want to use a prefix of /usr/local instead.
- Building with Intel compiler
** Version 8 and later
Starting with version 8, the preferred name for the IA-64 Intel compiler is "icc" (same name as on x86). Thus, the configure-line should look like this:
$ ./configure CC=icc CFLAGS="-g -O3 -ip" CXX=icc CCAS=gcc CCASFLAGS=-g \
LDFLAGS="-L$PWD/src/.libs"
- Building on HP-UX
For the time being, libunwind must be built with GCC on HP-UX.
libunwind should be configured and installed on HP-UX like this:
$ ./configure CFLAGS="-g -O2 -mlp64" CXXFLAGS="-g -O2 -mlp64"
Caveat: Unwinding of 32-bit (ILP32) binaries is not supported at the moment.
** Workaround for older versions of GCC
GCC v3.0 and GCC v3.2 ship with a bad version of sys/types.h. The workaround is to issue the following commands before running "configure":
$ mkdir $top_dir/include/sys
$ cp /usr/include/sys/types.h $top_dir/include/sys
GCC v3.3.2 or later have been fixed and do not require this workaround.
- Building for PowerPC64 / Linux
For building for power64 you should use:
$ ./configure CFLAGS="-g -O2 -m64" CXXFLAGS="-g -O2 -m64"
If your power support altivec registers: $ ./configure CFLAGS="-g -O2 -m64 -maltivec" CXXFLAGS="-g -O2 -m64 -maltivec"
To check if your processor has support for vector registers (altivec): cat /proc/cpuinfo | grep altivec and should have something like this: cpu : PPC970, altivec supported
If libunwind seems to not work (backtracing failing), try to compile it with -O0, without optimizations. There are some compiler problems depending on the version of your gcc.
- Building on FreeBSD
General building instructions apply. To build and execute several tests, you need libexecinfo library available in ports as devel/libexecinfo.
Development of the port was done of FreeBSD 8.0-STABLE. The library was build with the system compiler that is modified version of gcc 4.2.1, as well as the gcc 4.4.3.
- Regression Testing
After building the library, you can run a set of regression tests with:
$ make check
** Expected results on IA-64 Linux
Unless you have a very recent C library and compiler installed, it is currently expected to have the following tests fail on IA-64 Linux:
Gtest-init (should pass starting with glibc-2.3.x/gcc-3.4)
Ltest-init (should pass starting with glibc-2.3.x/gcc-3.4)
test-ptrace (should pass starting with glibc-2.3.x/gcc-3.4)
run-ia64-test-dyn1 (should pass starting with glibc-2.3.x)
This does not mean that libunwind cannot be used with older compilers or C libraries, it just means that for certain corner cases, unwinding will fail. Since they're corner cases, it is not likely for applications to trigger them.
Note: If you get lots of errors in Gia64-test-nat and Lia64-test-nat, it's almost certainly a sign of an old assembler. The GNU assembler used to encode previous-stack-pointer-relative offsets incorrectly. This bug was fixed on 21-Sep-2004 so any later assembler will be fine.
** Expected results on x86 Linux
The following tests are expected to fail on x86 Linux:
test-ptrace
** Expected results on x86-64 Linux
The following tests are expected to fail on x86-64 Linux:
run-ptrace-misc (see http://gcc.gnu.org/bugzilla/show_bug.cgi?id=18748
and http://gcc.gnu.org/bugzilla/show_bug.cgi?id=18749)
** Expected results on PARISC Linux
Caveat: GCC v3.4 or newer is needed on PA-RISC Linux. Earlier versions of the compiler failed to generate the exception-handling program header (GNU_EH_FRAME) needed for unwinding.
The following tests are expected to fail on x86-64 Linux:
Gtest-bt (backtrace truncated at kill() due to lack of unwind-info)
Ltest-bt (likewise)
Gtest-resume-sig (Gresume.c:my_rt_sigreturn() is wrong somehow)
Ltest-resume-sig (likewise)
Gtest-init (likewise)
Ltest-init (likewise)
Gtest-dyn1 (no dynamic unwind info support yet)
Ltest-dyn1 (no dynamic unwind info support yet)
test-setjmp (longjmp() not implemented yet)
run-check-namespace (toolchain doesn't support HIDDEN yet)
** Expected results on HP-UX
"make check" is currently unsupported for HP-UX. You can try to run it, but most tests will fail (and some may fail to terminate). The only test programs that are known to work at this time are:
tests/bt
tests/Gperf-simple
tests/test-proc-info
tests/test-static-link
tests/Gtest-init
tests/Ltest-init
tests/Gtest-resume-sig
tests/Ltest-resume-sig
** Expected results on PPC64 Linux
"make check" should run with no more than 10 out of 24 tests failed.
- Performance Testing
This distribution includes a few simple performance tests which give some idea of the basic cost of various libunwind operations. After building the library, you can run these tests with the following commands:
$ cd tests $ make perf
- Contacting the Developers
Please direct all questions regarding this library to:
You can do this by sending a mail to [email protected] with a body of:
subscribe libunwind-devel
or you can subscribe and manage your subscription via the web-interface at:
https://savannah.nongnu.org/mail/?group=libunwind
Or interact at the gihub page:
https://github.com/libunwind/libunwind