Wireshark-compatible all-channel Bluetooth sniffer for bladeRF, with wideband sniffing (4-60 MHz) for HackRF and USRP.
This tool requires libliquid, libhackrf, libbladerf, libuhd, and libfftw3. On Debian-based systems you can install these using:
sudo apt install libliquid-dev libhackrf-dev libbladerf-dev libuhd-dev libfftw3-dev
On macOS, fftw3 is not required and Homebrew is the recommended package manager:
brew install liquid-dsp hackrf libbladerf uhd
This code is untested against MacPorts. The deps can be installed with:
port install liquid-dsp hackrf bladeRF uhd
mkdir build
cd build
cmake ..
make
make install
The install target will copy the binary into /usr/local/bin (by
default) and will attempt to install into the system Wireshark directory
on Linux if detected. Use ice9-bluetooth --install to install the
binary into your local extcap dir ($HOME/.config/wireshark/extcap). An
uninstall target is also provided as a convenience.
This tool is primarily meant to be run from within Wireshark. That said, it is fully operable from the command line. Refer to the usage notes for full details. For a brief overview, to capture 20 channels centered on 2427 MHz and log all BLE traffic to a PCAP file:
./ice9-bluetooth -l -c 2427 -C 20 -w ble.pcap
To capture all channels (the default as of 23.06.0) run the following:
./ice9-bluetooth -l -i bladerf0 -a -w all_channels.pcap
For performance stats, add -s. For low-level details and info about
classic Bluetooth packets, add -v.
To use in Wireshark, plug in your SDR and launch Wireshark. Scroll to the bottom of the interfaces list in the main window and you should see "ICE9 Bluetooth: hackrf-$serial" (or similar) listed. Click the wheel icon to the left of it to configure it if you want, but the defaults should get you BLE packets (if your system is fast enough).
There isn't a proper benchmark mode as such, but you can try demodulating a bunch of random bytes like so:
./ice9-bluetooth -f /dev/urandom -s -C 20
or on macOS:
./ice9-bluetooth -f /dev/random -s -C 20
The channelizer will be the bottleneck. Start with 20 channels and observe the performance relative to real time. If it is not over 100%, lower the number of channels until it is. If it is over realtime, keep going until you reach 96 channels.
If you do benchmark this code, please share your numbers with me!
+----------------------------+
| polyphase channelizer |
| 1 x 20 MHz -> 20 x 2 MHz |
+-------+------+-------+-----+
| | |
| | |
| | |
+-----v----+ | +-----v-----+
| thread 1 | | | thread 2 |
+----------+ | +-----------+
| output:
| +-----------+ bursts
... +-> thread 20 |
+-----------+
burst queue
|
|
+-----------v-------------+
| burst processor |
| FM demod / BT detection |
+-------------------------+
The complex IQ samples come in from file or HackRF and are fed into a polyphase channelizer. This splits the n MHz input into n channels at 2 MHz wide. These channelized samples are fed to n threads that each process one channel. Each thread runs a "burst catcher", that uses Liquid's AGC to capture bursts on the channel and feeds them via a queue to the burst processor.
The burst processor takes the complex IQ bursts, FM demodulates them, performs carrier frequency offset (CFO) correction, normalizes them to roughly [-1.0, 1.0], bypasses symbol sync (for hysterical reasons), and performs hard bit decisions. These bit buffers are fed into the Bluetooth detectors. First we attempt to detect BR packets using libbtbb's techniques (borrowed from Ubertooth and earlier gr-bluetooth). If that fails, we then try to detect BLE packets.
This code is naughty and occasionally needs to be killed with prejudice
(kill -9). This happens most often in benchmark mode.
This code was written by Mike Ryan of ICE9 Consulting LLC. For more information visit https://ice9.us/