This repository has been archived by the owner on Jan 31, 2021. It is now read-only.
-
Notifications
You must be signed in to change notification settings - Fork 43
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
rpi: BCM2837 and Raspberry Pi 3 32-bit support
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with the CPU complex swapped out for a quad-core ARMv8. This can operate in 32- or 64-bit mode. 32-bit mode is the current default selected by the VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of U-Boot for the Raspberry Pi 3. From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a change in usage of the SoC UARTs. On all previous Pis, the PL011 was the only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a UART to connect to the SoC. By default, the PL011 is used for this purpose since it has larger FIFOs than the other "mini" UART. However, this can be configured via the VideoCore firmware's config.txt file. This patch hard-codes use of the mini UART in the RPi 3 port. If your system uses the PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot port instead. A future change might determine which UART to use at run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed together. The mini UART has some limitations. One externally visible issue in the BCM2837 integration is that the UART divides the SoC's "core clock" to generate the baud rate. The core clock is typically variable, and under control of the VideoCore firmware for thermal management reasons. If the VC FW does modify the core clock rate, UART communication will be corrupted since the baud rate will vary from the expected value. This was not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To work around this, the VideoCore firmware can be told not to modify the SoC core clock. However, the only way this can happen and be thermally safe is to limit the core clock to a low/minimum frequency. This leaves performance on the table for use-cases that don't care about a UART console. Consequently, use of the mini UART console must be explicitly requested by entering the following line into config.txt: enable_uart=1 A recent version of the VC firmware is required to ensure that the mini UART is fully and correctly initialized by the VC FW; at least firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on core clock See: raspberrypi/firmware#572". Signed-off-by: Stephen Warren <[email protected]> Reviewed-by: Tom Rini <[email protected]> --- v2: - Fix Kconfig syntax error. - Update required VC FW commit ID to cover MMC fix too.
- Loading branch information
Showing
7 changed files
with
84 additions
and
2 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,6 @@ | ||
RPI_3_32B BOARD | ||
M: Stephen Warren <[email protected]> | ||
S: Maintained | ||
F: board/raspberrypi/rpi_3_32b/ | ||
F: include/configs/rpi_3_32b.h | ||
F: configs/rpi_3_32b_defconfig |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,7 @@ | ||
# | ||
# (C) Copyright 2012-2016 Stephen Warren <[email protected]> | ||
# | ||
# SPDX-License-Identifier: GPL-2.0 | ||
# | ||
|
||
obj-y := ../rpi/rpi.o |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,11 @@ | ||
CONFIG_ARM=y | ||
CONFIG_ARCH_BCM283X=y | ||
CONFIG_TARGET_RPI_3_32B=y | ||
CONFIG_OF_BOARD_SETUP=y | ||
CONFIG_SYS_PROMPT="U-Boot> " | ||
# CONFIG_CMD_IMLS is not set | ||
# CONFIG_CMD_FLASH is not set | ||
# CONFIG_CMD_FPGA is not set | ||
CONFIG_CMD_GPIO=y | ||
CONFIG_PHYS_TO_BUS=y | ||
CONFIG_OF_LIBFDT=y |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Original file line number | Diff line number | Diff line change |
---|---|---|
@@ -0,0 +1,15 @@ | ||
/* | ||
* (C) Copyright 2012-2016 Stephen Warren <[email protected]> | ||
* | ||
* SPDX-License-Identifier: GPL-2.0 | ||
*/ | ||
|
||
#ifndef __CONFIG_H | ||
#define __CONFIG_H | ||
|
||
#define CONFIG_SKIP_LOWLEVEL_INIT | ||
#define CONFIG_SYS_CACHELINE_SIZE 64 | ||
|
||
#include "rpi-common.h" | ||
|
||
#endif |