✨ Polar Kinematics (MarlinFirmware#25214)

Marlin/Configuration.h

@@ -915,7 +915,7 @@
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+  #define PRINTABLE_RADIUS       140.0    // (mm)
 
   // Maximum reachable area
   #define DELTA_MAX_RADIUS       140.0    // (mm)
@@ -969,7 +969,7 @@
   #if ENABLED(MORGAN_SCARA)
 
     //#define DEBUG_SCARA_KINEMATICS
-    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+    #define FEEDRATE_SCALING        // Convert XY feedrate from mm/s to degrees/s on the fly
 
     // Radius around the center where the arm cannot reach
     #define MIDDLE_DEAD_ZONE_R   0  // (mm)
@@ -1004,7 +1004,7 @@
   #define TPARA_OFFSET_Y    0       // (mm)
   #define TPARA_OFFSET_Z    0       // (mm)
 
-  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+  #define FEEDRATE_SCALING        // Convert XY feedrate from mm/s to degrees/s on the fly
 
   // Radius around the center where the arm cannot reach
   #define MIDDLE_DEAD_ZONE_R   0  // (mm)
@@ -1014,6 +1014,59 @@
   #define PSI_HOMING_OFFSET    0
 #endif
 
+// @section polar
+
+/**
+ * POLAR Kinematics
+ *  developed by Kadir ilkimen for PolarBear CNC and babyBear
+ *  https://github.com/kadirilkimen/Polar-Bear-Cnc-Machine
+ *  https://github.com/kadirilkimen/babyBear-3D-printer
+ *
+ * A polar machine can have different configurations.
+ * This kinematics is only compatible with the following configuration:
+ *        X : Independent linear
+ *   Y or B : Polar
+ *        Z : Independent linear
+ *
+ * For example, PolarBear has CoreXZ plus Polar Y or B.
+ *
+ * Motion problem for Polar axis near center / origin:
+ *
+ * 3D printing:
+ * Movements very close to the center of the polar axis take more time than others.
+ * This brief delay results in more material deposition due to the pressure in the nozzle.
+ *
+ * Current Kinematics and feedrate scaling deals with this by making the movement as fast
+ * as possible. It works for slow movements but doesn't work well with fast ones. A more
+ * complicated extrusion compensation must be implemented.
+ *
+ * Ideally, it should estimate that a long rotation near the center is ahead and will cause
+ * unwanted deposition. Therefore it can compensate the extrusion beforehand.
+ *
+ * Laser cutting:
+ * Same thing would be a problem for laser engraving too. As it spends time rotating at the
+ * center point, more likely it will burn more material than it should. Therefore similar
+ * compensation would be implemented for laser-cutting operations.
+ *
+ * Milling:
+ * This shouldn't be a problem for cutting/milling operations.
+ */
+//#define POLAR
+#if ENABLED(POLAR)
+  #define DEFAULT_SEGMENTS_PER_SECOND 180   // If movement is choppy try lowering this value
+  #define PRINTABLE_RADIUS 82.0f            // (mm) Maximum travel of X axis
+
+  // Movements fall inside POLAR_FAST_RADIUS are assigned the highest possible feedrate
+  // to compensate unwanted deposition related to the near-origin motion problem.
+  #define POLAR_FAST_RADIUS 3.0f            // (mm)
+
+  // Radius which is unreachable by the tool.
+  // Needed if the tool is not perfectly aligned to the center of the polar axis.
+  #define POLAR_CENTER_OFFSET 0.0f          // (mm)
+
+  #define FEEDRATE_SCALING                  // Convert XY feedrate from mm/s to degrees/s on the fly
+#endif
+
 // @section machine
 
 // Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
@@ -1420,13 +1473,13 @@
   // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
   // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, PRINTABLE_RADIUS, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, PRINTABLE_RADIUS, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
 
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (PRINTABLE_RADIUS) * 0.75, 100.0 }
   #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
 
   #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position

Marlin/src/MarlinCore.cpp

@@ -168,6 +168,8 @@
   #include "module/polargraph.h"
 #elif IS_SCARA
   #include "module/scara.h"
+#elif ENABLED(POLAR)
+  #include "module/polar.h"
 #endif
 
 #if HAS_LEVELING

Marlin/src/core/language.h

@@ -279,6 +279,7 @@
 #define STR_S_SEG_PER_SEC                   "S<seg-per-sec>"
 #define STR_DELTA_SETTINGS                  "Delta (L<diagonal-rod> R<radius> H<height> S<seg-per-sec> XYZ<tower-angle-trim> ABC<rod-trim>)"
 #define STR_SCARA_SETTINGS                  "SCARA"
+#define STR_POLAR_SETTINGS                  "Polar"
 #define STR_POLARGRAPH_SETTINGS             "Polargraph"
 #define STR_SCARA_P_T_Z                     "P<theta-psi-offset> T<theta-offset> Z<home-offset>"
 #define STR_ENDSTOP_ADJUSTMENT              "Endstop adjustment"

Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp

@@ -334,16 +334,14 @@
 #else // UBL_SEGMENTED
 
   #if IS_SCARA
-    #define DELTA_SEGMENT_MIN_LENGTH 0.25 // SCARA minimum segment size is 0.25mm
-  #elif ENABLED(DELTA)
-    #define DELTA_SEGMENT_MIN_LENGTH 0.10 // mm (still subject to DEFAULT_SEGMENTS_PER_SECOND)
-  #elif ENABLED(POLARGRAPH)
-    #define DELTA_SEGMENT_MIN_LENGTH 0.10 // mm (still subject to DEFAULT_SEGMENTS_PER_SECOND)
+    #define SEGMENT_MIN_LENGTH 0.25 // SCARA minimum segment size is 0.25mm
+  #elif IS_KINEMATIC
+    #define SEGMENT_MIN_LENGTH 0.10 // (mm) Still subject to DEFAULT_SEGMENTS_PER_SECOND
   #else // CARTESIAN
     #ifdef LEVELED_SEGMENT_LENGTH
-      #define DELTA_SEGMENT_MIN_LENGTH LEVELED_SEGMENT_LENGTH
+      #define SEGMENT_MIN_LENGTH LEVELED_SEGMENT_LENGTH
     #else
-      #define DELTA_SEGMENT_MIN_LENGTH 1.00 // mm (similar to G2/G3 arc segmentation)
+      #define SEGMENT_MIN_LENGTH 1.00 // (mm) Similar to G2/G3 arc segmentation
     #endif
   #endif
 
@@ -361,23 +359,23 @@
     const xyze_pos_t total = destination - current_position;
 
     const float cart_xy_mm_2 = HYPOT2(total.x, total.y),
-                cart_xy_mm = SQRT(cart_xy_mm_2);                                     // Total XY distance
+                cart_xy_mm = SQRT(cart_xy_mm_2);                               // Total XY distance
 
     #if IS_KINEMATIC
-      const float seconds = cart_xy_mm / scaled_fr_mm_s;                             // Duration of XY move at requested rate
-      uint16_t segments = LROUND(segments_per_second * seconds),                     // Preferred number of segments for distance @ feedrate
-               seglimit = LROUND(cart_xy_mm * RECIPROCAL(DELTA_SEGMENT_MIN_LENGTH)); // Number of segments at minimum segment length
-      NOMORE(segments, seglimit);                                                    // Limit to minimum segment length (fewer segments)
+      const float seconds = cart_xy_mm / scaled_fr_mm_s;                       // Duration of XY move at requested rate
+      uint16_t segments = LROUND(segments_per_second * seconds),               // Preferred number of segments for distance @ feedrate
+               seglimit = LROUND(cart_xy_mm * RECIPROCAL(SEGMENT_MIN_LENGTH)); // Number of segments at minimum segment length
+      NOMORE(segments, seglimit);                                              // Limit to minimum segment length (fewer segments)
     #else
-      uint16_t segments = LROUND(cart_xy_mm * RECIPROCAL(DELTA_SEGMENT_MIN_LENGTH)); // Cartesian fixed segment length
+      uint16_t segments = LROUND(cart_xy_mm * RECIPROCAL(SEGMENT_MIN_LENGTH)); // Cartesian fixed segment length
     #endif
 
-    NOLESS(segments, 1U);                                                            // Must have at least one segment
-    const float inv_segments = 1.0f / segments;                                      // Reciprocal to save calculation
+    NOLESS(segments, 1U);                                                      // Must have at least one segment
+    const float inv_segments = 1.0f / segments;                                // Reciprocal to save calculation
 
     // Add hints to help optimize the move
-    PlannerHints hints(SQRT(cart_xy_mm_2 + sq(total.z)) * inv_segments);             // Length of each segment
-    #if ENABLED(SCARA_FEEDRATE_SCALING)
+    PlannerHints hints(SQRT(cart_xy_mm_2 + sq(total.z)) * inv_segments);       // Length of each segment
+    #if ENABLED(FEEDRATE_SCALING)
       hints.inv_duration = scaled_fr_mm_s / hints.millimeters;
     #endif
 

Marlin/src/gcode/calibrate/G33.cpp

@@ -407,12 +407,12 @@ void GcodeSuite::G33() {
                   towers_set = !parser.seen_test('T');
 
   // The calibration radius is set to a calculated value
-  float dcr = probe_at_offset ? DELTA_PRINTABLE_RADIUS : DELTA_PRINTABLE_RADIUS - PROBING_MARGIN;
+  float dcr = probe_at_offset ? PRINTABLE_RADIUS : PRINTABLE_RADIUS - PROBING_MARGIN;
   #if HAS_PROBE_XY_OFFSET
     const float total_offset = HYPOT(probe.offset_xy.x, probe.offset_xy.y);
     dcr -= probe_at_offset ? _MAX(total_offset, PROBING_MARGIN) : total_offset;
   #endif
-  NOMORE(dcr, DELTA_PRINTABLE_RADIUS);
+  NOMORE(dcr, PRINTABLE_RADIUS);
   if (parser.seenval('R')) dcr -= _MAX(parser.value_float(), 0.0f);
   TERN_(HAS_DELTA_SENSORLESS_PROBING, dcr *= sensorless_radius_factor);
 

Marlin/src/gcode/calibrate/M48.cpp

@@ -162,8 +162,8 @@ void GcodeSuite::M48() {
         float angle = random(0, 360);
         const float radius = random(
           #if ENABLED(DELTA)
-            int(0.1250000000 * (DELTA_PRINTABLE_RADIUS)),
-            int(0.3333333333 * (DELTA_PRINTABLE_RADIUS))
+            int(0.1250000000 * (PRINTABLE_RADIUS)),
+            int(0.3333333333 * (PRINTABLE_RADIUS))
           #else
             int(5), int(0.125 * _MIN(X_BED_SIZE, Y_BED_SIZE))
           #endif

Marlin/src/gcode/calibrate/M665.cpp

@@ -181,6 +181,25 @@
     );
   }
 
+#elif ENABLED(POLAR)
+
+  #include "../../module/polar.h"
+
+  /**
+   * M665: Set POLAR settings
+   * Parameters:
+   *   S[segments]  - Segments-per-second
+   */
+  void GcodeSuite::M665() {
+    if (!parser.seen_any()) return M665_report();
+    if (parser.seenval('S')) segments_per_second = parser.value_float();
+  }
+
+  void GcodeSuite::M665_report(const bool forReplay/*=true*/) {
+    report_heading_etc(forReplay, F(STR_POLAR_SETTINGS));
+    SERIAL_ECHOLNPGM_P(PSTR("  M665 S"), segments_per_second);
+  }
+
 #endif
 
 #endif // IS_KINEMATIC

Marlin/src/gcode/gcode.h

@@ -335,7 +335,7 @@
   #include "../feature/encoder_i2c.h"
 #endif
 
-#if IS_SCARA || defined(G0_FEEDRATE)
+#if EITHER(IS_SCARA, POLAR) || defined(G0_FEEDRATE)
   #define HAS_FAST_MOVES 1
 #endif
 

Marlin/src/gcode/host/M114.cpp

@@ -71,7 +71,7 @@
 
     #if IS_KINEMATIC
       // Kinematics applied to the leveled position
-      SERIAL_ECHOPGM(TERN(IS_SCARA, "ScaraK: ", "DeltaK: "));
+      SERIAL_ECHOPGM(TERN(POLAR, "Polar", TERN(IS_SCARA, "Scara", "Delta")) "K: " );
       inverse_kinematics(leveled);  // writes delta[]
       report_linear_axis_pos(delta);
     #endif

Marlin/src/gcode/host/M360.cpp

@@ -161,6 +161,7 @@ void GcodeSuite::M360() {
   SERIAL_ECHOLNPGM(
     TERN_(DELTA,         "Delta")
     TERN_(IS_SCARA,      "SCARA")
+    TERN_(POLAR,         "Polar")
     TERN_(IS_CORE,       "Core")
     TERN_(MARKFORGED_XY, "MarkForgedXY")
     TERN_(MARKFORGED_YX, "MarkForgedYX")

Marlin/src/gcode/motion/G0_G1.cpp

@@ -106,7 +106,7 @@ void GcodeSuite::G0_G1(TERN_(HAS_FAST_MOVES, const bool fast_move/*=false*/)) {
 
     #endif // FWRETRACT
 
-    #if IS_SCARA
+    #if EITHER(IS_SCARA, POLAR)
       fast_move ? prepare_fast_move_to_destination() : prepare_line_to_destination();
     #else
       prepare_line_to_destination();

Marlin/src/gcode/motion/G2_G3.cpp

@@ -218,7 +218,7 @@ void plan_arc(
 
   // Add hints to help optimize the move
   PlannerHints hints;
-  #if ENABLED(SCARA_FEEDRATE_SCALING)
+  #if ENABLED(FEEDRATE_SCALING)
     hints.inv_duration = (scaled_fr_mm_s / flat_mm) * segments;
   #endif
 

Marlin/src/inc/Conditionals_LCD.h

@@ -1406,7 +1406,7 @@
 #if ANY(MORGAN_SCARA, MP_SCARA, AXEL_TPARA)
   #define IS_SCARA 1
   #define IS_KINEMATIC 1
-#elif EITHER(DELTA, POLARGRAPH)
+#elif ANY(DELTA, POLARGRAPH, POLAR)
   #define IS_KINEMATIC 1
 #else
   #define IS_CARTESIAN 1

Marlin/src/inc/Conditionals_post.h

@@ -267,19 +267,19 @@
  */
 #if IS_KINEMATIC
   #undef LCD_BED_TRAMMING
+  #undef SLOWDOWN
 #endif
 
 /**
  * SCARA cannot use SLOWDOWN and requires QUICKHOME
  * Printable radius assumes joints can fully extend
  */
 #if IS_SCARA
-  #undef SLOWDOWN
   #if ENABLED(AXEL_TPARA)
-    #define SCARA_PRINTABLE_RADIUS (TPARA_LINKAGE_1 + TPARA_LINKAGE_2)
+    #define PRINTABLE_RADIUS (TPARA_LINKAGE_1 + TPARA_LINKAGE_2)
   #else
     #define QUICK_HOME
-    #define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
+    #define PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
   #endif
 #endif
 
@@ -378,7 +378,6 @@
  */
 #if ENABLED(DELTA)
   #undef Z_SAFE_HOMING
-  #undef SLOWDOWN
 #endif
 
 #ifndef MESH_INSET
@@ -3083,7 +3082,10 @@
 /**
  * Only constrain Z on DELTA / SCARA machines
  */
-#if IS_KINEMATIC
+#if ENABLED(POLAR)
+  #undef MIN_SOFTWARE_ENDSTOP_Y
+  #undef MAX_SOFTWARE_ENDSTOP_Y
+#elif IS_KINEMATIC
   #undef MIN_SOFTWARE_ENDSTOP_X
   #undef MIN_SOFTWARE_ENDSTOP_Y
   #undef MAX_SOFTWARE_ENDSTOP_X
@@ -3154,7 +3156,7 @@
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   #if IS_KINEMATIC
     // Probing points may be verified at compile time within the radius
-    // using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
+    // using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(PRINTABLE_RADIUS),"bad probe point!")
     // so that may be added to SanityCheck.h in the future.
     #define _MESH_MIN_X (X_MIN_BED + MESH_INSET)
     #define _MESH_MIN_Y (Y_MIN_BED + MESH_INSET)

Marlin/src/inc/SanityCheck.h

@@ -658,6 +658,12 @@
   #error "(POLAR|DELTA|SCARA|TPARA)_SEGMENTS_PER_SECOND is now DEFAULT_SEGMENTS_PER_SECOND."
 #elif ANY(DGUS_LCD_UI_ORIGIN, DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY, DGUS_LCD_UI_MKS, DGUS_LCD_UI_RELOADED) && !defined(DGUS_LCD_UI)
   #error "DGUS_LCD_UI_[TYPE] is now set using DGUS_LCD_UI TYPE."
+#elif defined(DELTA_PRINTABLE_RADIUS)
+  #error "DELTA_PRINTABLE_RADIUS is now PRINTABLE_RADIUS."
+#elif defined(SCARA_PRINTABLE_RADIUS)
+  #error "SCARA_PRINTABLE_RADIUS is now PRINTABLE_RADIUS."
+#elif defined(SCARA_FEEDRATE_SCALING)
+  #error "SCARA_FEEDRATE_SCALING is now FEEDRATE_SCALING."
 #endif
 
 // L64xx stepper drivers have been removed
@@ -1371,6 +1377,13 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   #endif
 #endif
 
+/**
+ * POLAR warnings
+ */
+#if BOTH(POLAR, S_CURVE_ACCELERATION)
+  #warning "POLAR Kinematics may not work well with S_CURVE_ACCELERATION."
+#endif
+
 /**
  * Special tool-changing options
  */
@@ -1666,8 +1679,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * Allow only one kinematic type to be defined
  */
-#if MANY(DELTA, MORGAN_SCARA, MP_SCARA, AXEL_TPARA, COREXY, COREXZ, COREYZ, COREYX, COREZX, COREZY, MARKFORGED_XY, MARKFORGED_YX, ARTICULATED_ROBOT_ARM, FOAMCUTTER_XYUV)
-  #error "Please enable only one of DELTA, MORGAN_SCARA, MP_SCARA, AXEL_TPARA, COREXY, COREXZ, COREYZ, COREYX, COREZX, COREZY, MARKFORGED_XY, MARKFORGED_YX, ARTICULATED_ROBOT_ARM, or FOAMCUTTER_XYUV."
+#if MANY(DELTA, MORGAN_SCARA, MP_SCARA, AXEL_TPARA, COREXY, COREXZ, COREYZ, COREYX, COREZX, COREZY, MARKFORGED_XY, MARKFORGED_YX, ARTICULATED_ROBOT_ARM, FOAMCUTTER_XYUV, POLAR)
+  #error "Please enable only one of DELTA, MORGAN_SCARA, MP_SCARA, AXEL_TPARA, COREXY, COREXZ, COREYZ, COREYX, COREZX, COREZY, MARKFORGED_XY, MARKFORGED_YX, ARTICULATED_ROBOT_ARM, FOAMCUTTER_XYUV, or POLAR."
 #endif
 
 /**
@@ -1695,7 +1708,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
  * Junction deviation is incompatible with kinematic systems.
  */
 #if HAS_JUNCTION_DEVIATION && IS_KINEMATIC
-  #error "CLASSIC_JERK is required for DELTA and SCARA."
+  #error "CLASSIC_JERK is required for DELTA, SCARA, and POLAR."
 #endif
 
 /**
@@ -1913,7 +1926,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
     static_assert(PROBING_MARGIN_RIGHT >= 0, "PROBING_MARGIN_RIGHT must be >= 0.");
   #endif
 
-  #define _MARGIN(A) TERN(IS_SCARA, SCARA_PRINTABLE_RADIUS, TERN(DELTA, DELTA_PRINTABLE_RADIUS, ((A##_BED_SIZE) / 2)))
+  #define _MARGIN(A) TERN(IS_KINEMATIC, PRINTABLE_RADIUS, ((A##_BED_SIZE) / 2))
   static_assert(PROBING_MARGIN       < _MARGIN(X), "PROBING_MARGIN is too large.");
   static_assert(PROBING_MARGIN_BACK  < _MARGIN(Y), "PROBING_MARGIN_BACK is too large.");
   static_assert(PROBING_MARGIN_FRONT < _MARGIN(Y), "PROBING_MARGIN_FRONT is too large.");
@@ -2004,6 +2017,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 
   #if IS_SCARA
     #error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers."
+  #elif ENABLED(POLAR)
+    #error "AUTO_BED_LEVELING_UBL does not yet support POLAR printers."
   #elif DISABLED(EEPROM_SETTINGS)
     #error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS."
   #elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15)