Merge branch 'bugfix-2.0.x' into 2.0.x-Sapphire-Pro

Marlin/Configuration.h

@@ -99,6 +99,7 @@
 /**
  * Select the serial port on the board to use for communication with the host.
  * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
  * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
@@ -107,9 +108,6 @@
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
- * This allows the connection of wireless adapters (for instance) to non-default port pins.
- * Serial port -1 is the USB emulated serial port, if available.
- *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
 #define SERIAL_PORT_2 1
@@ -475,7 +473,7 @@
 #if ENABLED(PIDTEMP)
   //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
   //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
-  //#define PID_DEBUG             // Sends debug data to the serial port.
+  //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
   //#define PID_OPENLOOP 1        // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)

Marlin/src/HAL/DUE/HAL.h

@@ -39,7 +39,7 @@
 #include <stdint.h>
 
 // Define MYSERIAL0/1 before MarlinSerial includes!
-#if SERIAL_PORT == -1
+#if SERIAL_PORT == -1 || ENABLED(EMERGENCY_PARSER)
   #define MYSERIAL0 customizedSerial1
 #elif SERIAL_PORT == 0
   #define MYSERIAL0 Serial
@@ -56,7 +56,7 @@
 #ifdef SERIAL_PORT_2
   #if SERIAL_PORT_2 == SERIAL_PORT
     #error "SERIAL_PORT_2 must be different from SERIAL_PORT. Please update your configuration."
-  #elif SERIAL_PORT_2 == -1
+  #elif SERIAL_PORT_2 == -1 || ENABLED(EMERGENCY_PARSER)
     #define MYSERIAL1 customizedSerial2
   #elif SERIAL_PORT_2 == 0
     #define MYSERIAL1 Serial
@@ -94,7 +94,6 @@
   #endif
 #endif
 
-
 #include "MarlinSerial.h"
 #include "MarlinSerialUSB.h"
 

Marlin/src/HAL/DUE/MarlinSerial.cpp

@@ -629,23 +629,13 @@ void MarlinSerial<Cfg>::printFloat(double number, uint8_t digits) {
 
 // If not using the USB port as serial port
 #if SERIAL_PORT >= 0
-
-  // Preinstantiate
-  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT>>;
-
-  // Instantiate
-  MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;
-
+  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT>>;      // Define
+  MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;   // Instantiate
 #endif
 
-#ifdef SERIAL_PORT_2
-
-  // Preinstantiate
-  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>>;
-
-  // Instantiate
-  MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2;
-
+#if defined(SERIAL_PORT_2) && SERIAL_PORT_2 >= 0
+  template class MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>>;    // Define
+  MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2; // Instantiate
 #endif
 
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/MarlinSerial.h

@@ -172,13 +172,9 @@ struct MarlinSerialCfg {
 };
 
 #if SERIAL_PORT >= 0
-
   extern MarlinSerial<MarlinSerialCfg<SERIAL_PORT>> customizedSerial1;
+#endif
 
-#endif // SERIAL_PORT >= 0
-
-#ifdef SERIAL_PORT_2
-
+#if defined(SERIAL_PORT_2) && SERIAL_PORT_2 >= 0
   extern MarlinSerial<MarlinSerialCfg<SERIAL_PORT_2>> customizedSerial2;
-
 #endif

Marlin/src/HAL/DUE/MarlinSerialUSB.cpp

@@ -29,7 +29,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if SERIAL_PORT == -1
+#if HAS_USB_SERIAL
 
 #include "MarlinSerialUSB.h"
 
@@ -283,8 +283,12 @@ void MarlinSerialUSB::printFloat(double number, uint8_t digits) {
 }
 
 // Preinstantiate
-MarlinSerialUSB customizedSerial1;
-
-#endif // SERIAL_PORT == -1
+#if SERIAL_PORT == -1
+  MarlinSerialUSB customizedSerial1;
+#endif
+#if SERIAL_PORT_2 == -1
+  MarlinSerialUSB customizedSerial2;
+#endif
 
+#endif // HAS_USB_SERIAL
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/MarlinSerialUSB.h

@@ -28,7 +28,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if SERIAL_PORT == -1
+#if HAS_USB_SERIAL
 
 #include <WString.h>
 
@@ -88,6 +88,12 @@ class MarlinSerialUSB {
   static void printFloat(double, uint8_t);
 };
 
-extern MarlinSerialUSB customizedSerial1;
+#if SERIAL_PORT == -1
+  extern MarlinSerialUSB customizedSerial1;
+#endif
+
+#if SERIAL_PORT_2 == -1
+  extern MarlinSerialUSB customizedSerial2;
+#endif
 
-#endif // SERIAL_PORT == -1
+#endif // HAS_USB_SERIAL

Marlin/src/HAL/DUE/fastio/G2_PWM.cpp

@@ -46,6 +46,31 @@
 
 #include "G2_PWM.h"
 
+#if PIN_EXISTS(MOTOR_CURRENT_PWM_X)
+  #define G2_PWM_X 1
+#else
+  #define G2_PWM_X 0
+#endif
+#if PIN_EXISTS(MOTOR_CURRENT_PWM_Y)
+  #define G2_PWM_Y 1
+#else
+  #define G2_PWM_Y 0
+#endif
+#if PIN_EXISTS(MOTOR_CURRENT_PWM_Z)
+  #define G2_PWM_Z 1
+#else
+  #define G2_PWM_Z 0
+#endif
+#if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
+  #define G2_PWM_E 1
+#else
+  #define G2_PWM_E 0
+#endif
+#define G2_MASK_X(V) (G2_PWM_X * (V))
+#define G2_MASK_Y(V) (G2_PWM_Y * (V))
+#define G2_MASK_Z(V) (G2_PWM_Z * (V))
+#define G2_MASK_E(V) (G2_PWM_E * (V))
+
 volatile uint32_t *SODR_A = &PIOA->PIO_SODR,
                   *SODR_B = &PIOB->PIO_SODR,
                   *CODR_A = &PIOA->PIO_CODR,
@@ -55,10 +80,18 @@ PWM_map ISR_table[NUM_PWMS] = PWM_MAP_INIT;
 
 void Stepper::digipot_init() {
 
-  OUT_WRITE(MOTOR_CURRENT_PWM_X_PIN, 0);  // init pins
-  OUT_WRITE(MOTOR_CURRENT_PWM_Y_PIN, 0);
-  OUT_WRITE(MOTOR_CURRENT_PWM_Z_PIN, 0);
-  OUT_WRITE(MOTOR_CURRENT_PWM_E_PIN, 0);
+  #if PIN_EXISTS(MOTOR_CURRENT_PWM_X)
+    OUT_WRITE(MOTOR_CURRENT_PWM_X_PIN, 0);  // init pins
+  #endif
+  #if PIN_EXISTS(MOTOR_CURRENT_PWM_Y)
+    OUT_WRITE(MOTOR_CURRENT_PWM_Y_PIN, 0);
+  #endif
+  #if G2_PWM_Z
+    OUT_WRITE(MOTOR_CURRENT_PWM_Z_PIN, 0);
+  #endif
+  #if G2_PWM_E
+    OUT_WRITE(MOTOR_CURRENT_PWM_E_PIN, 0);
+  #endif
 
   #define WPKEY          (0x50574D << 8) // “PWM” in ASCII
   #define WPCMD_DIS_SW   0  // command to disable Write Protect SW
@@ -71,30 +104,51 @@ void Stepper::digipot_init() {
   PWM->PWM_WPCR = WPKEY | WPRG_ALL | WPCMD_DIS_SW;        // enable setting of all PWM registers
   PWM->PWM_CLK = PWM_CLOCK_F;                             // enable CLK_A and set it to 1MHz, leave CLK_B disabled
   PWM->PWM_CH_NUM[0].PWM_CMR = 0b1011;                    // set channel 0 to Clock A input & to left aligned
-  PWM->PWM_CH_NUM[1].PWM_CMR = 0b1011;                    // set channel 1 to Clock A input & to left aligned
-  PWM->PWM_CH_NUM[2].PWM_CMR = 0b1011;                    // set channel 2 to Clock A input & to left aligned
-  PWM->PWM_CH_NUM[3].PWM_CMR = 0b1011;                    // set channel 3 to Clock A input & to left aligned
-  PWM->PWM_CH_NUM[4].PWM_CMR = 0b1011;                    // set channel 4 to Clock A input & to left aligned
+  if (G2_PWM_X) PWM->PWM_CH_NUM[1].PWM_CMR = 0b1011;      // set channel 1 to Clock A input & to left aligned
+  if (G2_PWM_Y) PWM->PWM_CH_NUM[2].PWM_CMR = 0b1011;      // set channel 2 to Clock A input & to left aligned
+  if (G2_PWM_Z) PWM->PWM_CH_NUM[3].PWM_CMR = 0b1011;      // set channel 3 to Clock A input & to left aligned
+  if (G2_PWM_E) PWM->PWM_CH_NUM[4].PWM_CMR = 0b1011;      // set channel 4 to Clock A input & to left aligned
 
   PWM->PWM_CH_NUM[0].PWM_CPRD = PWM_PERIOD_US;            // set channel 0 Period
 
   PWM->PWM_IER2 = PWM_IER1_CHID0;                         // generate interrupt when counter0 overflows
-  PWM->PWM_IER2 = PWM_IER2_CMPM0 | PWM_IER2_CMPM1 | PWM_IER2_CMPM2 | PWM_IER2_CMPM3 | PWM_IER2_CMPM4;        // generate interrupt on compare event
-
-  PWM->PWM_CMP[1].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0]));   // interrupt when counter0 == CMPV - used to set Motor 1 PWM inactive
-  PWM->PWM_CMP[2].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0]));   // interrupt when counter0 == CMPV - used to set Motor 2 PWM inactive
-  PWM->PWM_CMP[3].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[1]));   // interrupt when counter0 == CMPV - used to set Motor 3 PWM inactive
-  PWM->PWM_CMP[4].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[2]));   // interrupt when counter0 == CMPV - used to set Motor 4 PWM inactive
-
-  PWM->PWM_CMP[1].PWM_CMPM = 0x0001;  // enable compare event
-  PWM->PWM_CMP[2].PWM_CMPM = 0x0001;  // enable compare event
-  PWM->PWM_CMP[3].PWM_CMPM = 0x0001;  // enable compare event
-  PWM->PWM_CMP[4].PWM_CMPM = 0x0001;  // enable compare event
-
-  PWM->PWM_SCM = PWM_SCM_UPDM_MODE0 | PWM_SCM_SYNC0 | PWM_SCM_SYNC1 | PWM_SCM_SYNC2 | PWM_SCM_SYNC3 | PWM_SCM_SYNC4; // sync 1-4 with 0, use mode 0 for updates
-
-  PWM->PWM_ENA = PWM_ENA_CHID0 | PWM_ENA_CHID1 | PWM_ENA_CHID2 | PWM_ENA_CHID3 | PWM_ENA_CHID4;         // enable the channels used by G2
-  PWM->PWM_IER1 = PWM_IER1_CHID0 | PWM_IER1_CHID1 | PWM_IER1_CHID2 | PWM_IER1_CHID3 | PWM_IER1_CHID4;        // enable interrupts for the channels used by G2
+  PWM->PWM_IER2 = PWM_IER2_CMPM0
+    | G2_MASK_X(PWM_IER2_CMPM1)
+    | G2_MASK_Y(PWM_IER2_CMPM2)
+    | G2_MASK_Z(PWM_IER2_CMPM3)
+    | G2_MASK_E(PWM_IER2_CMPM4)
+  ; // generate interrupt on compare event
+
+  if (G2_PWM_X) PWM->PWM_CMP[1].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 1 PWM inactive
+  if (G2_PWM_Y) PWM->PWM_CMP[2].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 2 PWM inactive
+  if (G2_PWM_Z) PWM->PWM_CMP[3].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[1])); // interrupt when counter0 == CMPV - used to set Motor 3 PWM inactive
+  if (G2_PWM_E) PWM->PWM_CMP[4].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[2])); // interrupt when counter0 == CMPV - used to set Motor 4 PWM inactive
+
+  if (G2_PWM_X) PWM->PWM_CMP[1].PWM_CMPM = 0x0001;  // enable compare event
+  if (G2_PWM_Y) PWM->PWM_CMP[2].PWM_CMPM = 0x0001;  // enable compare event
+  if (G2_PWM_Z) PWM->PWM_CMP[3].PWM_CMPM = 0x0001;  // enable compare event
+  if (G2_PWM_E) PWM->PWM_CMP[4].PWM_CMPM = 0x0001;  // enable compare event
+
+  PWM->PWM_SCM = PWM_SCM_UPDM_MODE0 | PWM_SCM_SYNC0
+    | G2_MASK_X(PWM_SCM_SYNC1)
+    | G2_MASK_Y(PWM_SCM_SYNC2)
+    | G2_MASK_Z(PWM_SCM_SYNC3)
+    | G2_MASK_E(PWM_SCM_SYNC4)
+  ; // sync 1-4 with 0, use mode 0 for updates
+
+  PWM->PWM_ENA = PWM_ENA_CHID0
+    | G2_MASK_X(PWM_ENA_CHID1)
+    | G2_MASK_Y(PWM_ENA_CHID2)
+    | G2_MASK_Z(PWM_ENA_CHID3)
+    | G2_MASK_E(PWM_ENA_CHID4)
+  ; // enable channels used by G2
+
+  PWM->PWM_IER1 = PWM_IER1_CHID0
+    | G2_MASK_X(PWM_IER1_CHID1)
+    | G2_MASK_Y(PWM_IER1_CHID2)
+    | G2_MASK_Z(PWM_IER1_CHID3)
+    | G2_MASK_E(PWM_IER1_CHID4)
+  ; // enable interrupts for channels used by G2
 
   NVIC_EnableIRQ(PWM_IRQn);     // Enable interrupt handler
   NVIC_SetPriority(PWM_IRQn, NVIC_EncodePriority(0, 10, 0));  // normal priority for PWM module (can stand some jitter on the Vref signals)
@@ -105,20 +159,27 @@ void Stepper::digipot_current(const uint8_t driver, const int16_t current) {
   if (!(PWM->PWM_CH_NUM[0].PWM_CPRD == PWM_PERIOD_US)) digipot_init();  // Init PWM system if needed
 
   switch (driver) {
-    case 0: PWM->PWM_CMP[1].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update X & Y
-            PWM->PWM_CMP[2].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));
-            PWM->PWM_CMP[1].PWM_CMPMUPD = 0x0001;  // enable compare event
-            PWM->PWM_CMP[2].PWM_CMPMUPD = 0x0001;  // enable compare event
-            PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
-            break;
-    case 1: PWM->PWM_CMP[3].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update Z
-            PWM->PWM_CMP[3].PWM_CMPMUPD = 0x0001;  // enable compare event
-            PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
-            break;
-    default:PWM->PWM_CMP[4].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update E
-            PWM->PWM_CMP[4].PWM_CMPMUPD = 0x0001;  // enable compare event
-            PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
-            break;
+    case 0:
+      if (G2_PWM_X) PWM->PWM_CMP[1].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update X & Y
+      if (G2_PWM_Y) PWM->PWM_CMP[2].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));
+      if (G2_PWM_X) PWM->PWM_CMP[1].PWM_CMPMUPD = 0x0001;  // enable compare event
+      if (G2_PWM_Y) PWM->PWM_CMP[2].PWM_CMPMUPD = 0x0001;  // enable compare event
+      if (G2_PWM_X || G2_PWM_Y) PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
+      break;
+    case 1:
+      if (G2_PWM_Z) {
+        PWM->PWM_CMP[3].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update Z
+        PWM->PWM_CMP[3].PWM_CMPMUPD = 0x0001;  // enable compare event
+        PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
+      }
+      break;
+    default:
+      if (G2_PWM_E) {
+        PWM->PWM_CMP[4].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));    // update E
+        PWM->PWM_CMP[4].PWM_CMPMUPD = 0x0001;  // enable compare event
+        PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
+      }
+      break;
   }
 }
 
@@ -127,17 +188,17 @@ volatile uint32_t PWM_ISR1_STATUS, PWM_ISR2_STATUS;
 void PWM_Handler() {
   PWM_ISR1_STATUS = PWM->PWM_ISR1;
   PWM_ISR2_STATUS = PWM->PWM_ISR2;
-  if (PWM_ISR1_STATUS & PWM_IER1_CHID0) {                           // CHAN_0 interrupt
-    *ISR_table[0].set_register = ISR_table[0].write_mask;                                          // set X to active
-    *ISR_table[1].set_register = ISR_table[1].write_mask;                                          // set Y to active
-    *ISR_table[2].set_register = ISR_table[2].write_mask;                                          // set Z to active
-    *ISR_table[3].set_register = ISR_table[3].write_mask;                                          // set E to active
+  if (PWM_ISR1_STATUS & PWM_IER1_CHID0) {                                                         // CHAN_0 interrupt
+    if (G2_PWM_X) *ISR_table[0].set_register = ISR_table[0].write_mask;                           // set X to active
+    if (G2_PWM_Y) *ISR_table[1].set_register = ISR_table[1].write_mask;                           // set Y to active
+    if (G2_PWM_Z) *ISR_table[2].set_register = ISR_table[2].write_mask;                           // set Z to active
+    if (G2_PWM_E) *ISR_table[3].set_register = ISR_table[3].write_mask;                           // set E to active
   }
   else {
-    if (PWM_ISR2_STATUS & PWM_IER2_CMPM1)  *ISR_table[0].clr_register = ISR_table[0].write_mask;   // set X to inactive
-    if (PWM_ISR2_STATUS & PWM_IER2_CMPM2)  *ISR_table[1].clr_register = ISR_table[1].write_mask;   // set Y to inactive
-    if (PWM_ISR2_STATUS & PWM_IER2_CMPM3)  *ISR_table[2].clr_register = ISR_table[2].write_mask;   // set Z to inactive
-    if (PWM_ISR2_STATUS & PWM_IER2_CMPM4)  *ISR_table[3].clr_register = ISR_table[3].write_mask;   // set E to inactive
+    if (G2_PWM_X && (PWM_ISR2_STATUS & PWM_IER2_CMPM1)) *ISR_table[0].clr_register = ISR_table[0].write_mask; // set X to inactive
+    if (G2_PWM_Y && (PWM_ISR2_STATUS & PWM_IER2_CMPM2)) *ISR_table[1].clr_register = ISR_table[1].write_mask; // set Y to inactive
+    if (G2_PWM_Z && (PWM_ISR2_STATUS & PWM_IER2_CMPM3)) *ISR_table[2].clr_register = ISR_table[2].write_mask; // set Z to inactive
+    if (G2_PWM_E && (PWM_ISR2_STATUS & PWM_IER2_CMPM4)) *ISR_table[3].clr_register = ISR_table[3].write_mask; // set E to inactive
   }
   return;
 }

Marlin/src/HAL/LPC1768/HAL.cpp

@@ -67,9 +67,7 @@ int16_t PARSED_PIN_INDEX(const char code, const int16_t dval) {
   return ind > -1 ? ind : dval;
 }
 
-void flashFirmware(int16_t value) {
-  NVIC_SystemReset();
-}
+void flashFirmware(const int16_t) { NVIC_SystemReset(); }
 
 void HAL_clear_reset_source(void) {
   #if ENABLED(USE_WATCHDOG)

Marlin/src/HAL/LPC1768/HAL.h

@@ -195,7 +195,7 @@ int16_t PARSED_PIN_INDEX(const char code, const int16_t dval);
 void HAL_idletask();
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);
 
 /**
  * set_pwm_frequency

Marlin/src/HAL/STM32/HAL.cpp

@@ -133,6 +133,6 @@ void HAL_adc_start_conversion(const uint8_t adc_pin) { HAL_adc_result = analogRe
 
 uint16_t HAL_adc_get_result() { return HAL_adc_result; }
 
-void flashFirmware(int16_t) { NVIC_SystemReset(); }
+void flashFirmware(const int16_t) { NVIC_SystemReset(); }
 
 #endif // ARDUINO_ARCH_STM32 && !STM32GENERIC

Marlin/src/HAL/STM32/HAL.h

@@ -223,4 +223,4 @@ uint16_t HAL_adc_get_result();
 #define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval)
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);

Marlin/src/HAL/STM32F1/HAL.cpp

@@ -388,6 +388,6 @@ void analogWrite(pin_t pin, int pwm_val8) {
     analogWrite(uint8_t(pin), pwm_val8);
 }
 
-void flashFirmware(int16_t value) { nvic_sys_reset(); }
+void flashFirmware(const int16_t) { nvic_sys_reset(); }
 
 #endif // __STM32F1__

Marlin/src/HAL/STM32F1/HAL.h

@@ -160,6 +160,7 @@ void HAL_idletask();
 
 #ifndef digitalPinHasPWM
   #define digitalPinHasPWM(P) (PIN_MAP[P].timer_device != nullptr)
+  #define NO_COMPILE_TIME_PWM
 #endif
 
 #define CRITICAL_SECTION_START()  uint32_t primask = __get_primask(); (void)__iCliRetVal()
@@ -287,4 +288,4 @@ void analogWrite(pin_t pin, int pwm_val8); // PWM only! mul by 257 in maple!?
 #define JTAGSWD_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_NONE)
 
 #define PLATFORM_M997_SUPPORT
-void flashFirmware(int16_t value);
+void flashFirmware(const int16_t);