Fix Reflex CTRL SNES Pinout, Rename Reflex Encode, Add Reflex Encode V2

.github/workflows/cmake.yml

@@ -23,7 +23,7 @@ jobs:
     runs-on: ubuntu-latest
     strategy:
       matrix:
-        GP2040_BOARDCONFIG: [Pico, PicoW, AlpacaOwO, BentoBox, DURAL, FightboardV3, FightboardV3Mirrored, FlatboxRev4, FlatboxRev5, FlatboxRev5RGB, FlatboxRev5Southpaw, KB2040, KeyboardConverter, Liatris, MavercadeKeebfighter, OpenCore0, OpenCore0WASD, PicoAnn, PicoFightingBoard, ReflexCtrlSNES, ReflexEncoder, RP2040AdvancedBreakoutBoard, RP2040AdvancedBreakoutBoardUSBPassthrough, RP2040MiniBreakoutBoard, SparkFunProMicro, WaveshareZero, Stress, SGFDevices  ]
+        GP2040_BOARDCONFIG: [Pico, PicoW, AlpacaOwO, BentoBox, DURAL, FightboardV3, FightboardV3Mirrored, FlatboxRev4, FlatboxRev5, FlatboxRev5RGB, FlatboxRev5Southpaw, KB2040, KeyboardConverter, Liatris, MavercadeKeebfighter, OpenCore0, OpenCore0WASD, PicoAnn, PicoFightingBoard, ReflexCtrlSNES, ReflexEncodeV1, ReflexEncodeV2, RP2040AdvancedBreakoutBoard, RP2040AdvancedBreakoutBoardUSBPassthrough, RP2040MiniBreakoutBoard, SparkFunProMicro, WaveshareZero, Stress, SGFDevices  ]
 
     steps:
     #Global Setup

configs/ReflexCtrlSNES/BoardConfig.h

@@ -10,6 +10,8 @@
 
 #define BOARD_CONFIG_LABEL "Reflex Ctrl SNES"
 
+#define DEFAULT_INPUT_MODE INPUT_MODE_SWITCH
+
 // This is the main pin definition section.
 // This will let you specify which GPIO pin each button is assigned too.
 // You can set any of the main pins as `-1` to disable it.
@@ -28,12 +30,12 @@
 #define PIN_BUTTON_L2   9           // L2 / LT / ZL / L2 / 7 / K4
 #define PIN_BUTTON_B3   10          // B3 / X / Y / Square / 1 / P1
 #define PIN_BUTTON_B4   11          // B4 / Y / X / Triangle / 4 / P2
-#define PIN_BUTTON_R1   12          // R1 / RB / R / R1 / 6 / P3
-#define PIN_BUTTON_L1   13          // L1 / LB / L / L1 / 5 / P4
+#define PIN_BUTTON_R1   19          // R1 / RB / R / R1 / 6 / P3
+#define PIN_BUTTON_L1   18          // L1 / LB / L / L1 / 5 / P4
 #define PIN_BUTTON_S1   16          // S1 / Back / Minus / Select / 9 / Coin
 #define PIN_BUTTON_S2   17          // S2 / Start / Plus / Start / 10 / Start
-#define PIN_BUTTON_L3   18          // L3 / LS / LS / L3 / 11 / LS
-#define PIN_BUTTON_R3   19          // R3 / RS / RS / R3 / 12 / RS
+#define PIN_BUTTON_L3   12          // L3 / LS / LS / L3 / 11 / LS
+#define PIN_BUTTON_R3   13          // R3 / RS / RS / R3 / 12 / RS
 #define PIN_BUTTON_A1   20          // A1 / Guide / Home / PS / 13 / ~
 #define PIN_BUTTON_A2   21          // A2 / ~ / Capture / ~ / 14 / ~
 #define PIN_BUTTON_FN   -1          // Hotkey Function
@@ -84,9 +86,7 @@
 // The default LEDS_[BUTTON] is an order and has nothing to do with what GPIO pin something is connected to.
 // Unless you are planning on running custom animations I would recommmend you leave this as is.
 
-#define TURBO_LED_PIN 15
-
-#define BOARD_LEDS_PIN 28
+#define TURBO_LED_PIN -1
 
 #define LED_BRIGHTNESS_MAXIMUM 150
 #define LED_BRIGHTNESS_STEPS 5

configs/ReflexEncoder/BoardConfig.h → configs/ReflexEncodeV1/BoardConfig.h

@@ -8,14 +8,17 @@
 
 #include "enums.pb.h"
 
-#define BOARD_CONFIG_LABEL "Reflex Encoder"
+#define BOARD_CONFIG_LABEL "Reflex Encode V1"
+
+#define DEFAULT_PS4CONTROLLER_TYPE PS4_ARCADESTICK
+#define DEFAULT_INPUT_MODE INPUT_MODE_PS4
 
 // This is the main pin definition section.
 // This will let you specify which GPIO pin each button is assigned too.
 // You can set any of the main pins as `-1` to disable it.
 // The Turbo pin and LS + RS slider pins can also be set to `-1` to disable that functionality.
 // Please note that only when `PIN_BUTTON_TURBO` is set to `-1` will the `T##` be removed from a connected display.
-// Please note that only when `PIN_SLIDER_ONE` and  `PIN_SLIDER_TWO` are set to `-1` will the button combo shortcut for DP/LS/RS work.
+// Please note that only when `PIN_SLIDER_LS` and  `PIN_SLIDER_RS` are set to `-1` will the button combo shortcut for DP/LS/RS work.
 // The buttons are listed in GP2040 configuration, beside each the listed order is *GP2040 / Xinput / Switch / PS3 / Directinput / Arcade*
 
 #define PIN_DPAD_UP     2           // UP
@@ -39,8 +42,8 @@
 #define PIN_BUTTON_FN   -1          // Hotkey Function
 #define PIN_BUTTON_TURBO 14         // Turbo
 #define PIN_BUTTON_REVERSE -1       // UDLR Reverse
-#define PIN_SLIDER_ONE    -1         // Left Stick Slider
-#define PIN_SLIDER_TWO    -1         // Right Stick Slider
+#define PIN_SLIDER_LS    -1         // Left Stick Slider
+#define PIN_SLIDER_RS    -1         // Right Stick Slider
 #define PIN_SLIDER_SOCD_ONE    -1         // SOCD Slider Pin One
 #define PIN_SLIDER_SOCD_TWO    -1         // SOCD Slider Pin Two
 
@@ -62,8 +65,6 @@
 #define DEFAULT_FORCED_SETUP_MODE FORCED_SETUP_MODE_OFF // 	FORCED_SETUP_MODE_OFF, FORCED_SETUP_MODE_LOCK_MODE_SWITCH, FORCED_SETUP_MODE_LOCK_WEB_CONFIG, FORCED_SETUP_MODE_LOCK_BOTH
 #define DEFAULT_LOCK_HOTKEYS false // or true
 
-#define DEFAULT_PS4CONTROLLER_TYPE PS4_CONTROLLER
-
 // This is the LEDs section.
 // The default `TURBO_LED_PIN` pin is set to `15` ( it is recommended to run through 3V3(OUT) with a resistor)
 // The Turbo LED will flash at a speed consistant with the set speed of the Turbo when a Turbo button is active.
@@ -86,9 +87,7 @@
 // The default LEDS_[BUTTON] is an order and has nothing to do with what GPIO pin something is connected to.
 // Unless you are planning on running custom animations I would recommmend you leave this as is.
 
-#define TURBO_LED_PIN 15
-
-#define BOARD_LEDS_PIN 28
+#define TURBO_LED_PIN -1
 
 #define LED_BRIGHTNESS_MAXIMUM 150
 #define LED_BRIGHTNESS_STEPS 5
@@ -228,7 +227,7 @@
 // INPUT_TEST     - Blinks whenever any input is made
 
 #define BOARD_LED_ENABLED 1
-#define BOARD_LED_TYPE ON_BOARD_LED_MODE_INPUT_TEST
+#define BOARD_LED_TYPE ON_BOARD_LED_MODE_PS_AUTH
 
 // Dual Directional Add-on Options
 

configs/ReflexEncodeV2/BoardConfig.h

@@ -0,0 +1,273 @@
+/*
+ * SPDX-License-Identifier: MIT
+ * SPDX-FileCopyrightText: Copyright (c) 2021 Jason Skuby (mytechtoybox.com)
+ */
+
+#ifndef PICO_BOARD_CONFIG_H_
+#define PICO_BOARD_CONFIG_H_
+
+#include "enums.pb.h"
+
+#define BOARD_CONFIG_LABEL "Reflex Encode V2"
+
+#define DEFAULT_PS4CONTROLLER_TYPE PS4_ARCADESTICK
+#define DEFAULT_INPUT_MODE INPUT_MODE_PS4
+#define PSPASSTHROUGH_ENABLED 1
+#define PSPASSTHROUGH_PIN_DPLUS 14
+
+// This is the main pin definition section.
+// This will let you specify which GPIO pin each button is assigned too.
+// You can set any of the main pins as `-1` to disable it.
+// The Turbo pin and LS + RS slider pins can also be set to `-1` to disable that functionality.
+// Please note that only when `PIN_BUTTON_TURBO` is set to `-1` will the `T##` be removed from a connected display.
+// Please note that only when `PIN_SLIDER_LS` and  `PIN_SLIDER_RS` are set to `-1` will the button combo shortcut for DP/LS/RS work.
+// The buttons are listed in GP2040 configuration, beside each the listed order is *GP2040 / Xinput / Switch / PS3 / Directinput / Arcade
+
+#define PIN_DPAD_UP     2           // UP
+#define PIN_DPAD_DOWN   3           // DOWN
+#define PIN_DPAD_RIGHT  4           // RIGHT
+#define PIN_DPAD_LEFT   5           // LEFT
+#define PIN_BUTTON_B1   6           // B1 / A / B / Cross / 2 / K1
+#define PIN_BUTTON_B2   7           // B2 / B / A / Circle / 3 / K2
+#define PIN_BUTTON_R2   8           // R2 / RT / ZR / R2 / 8 / K3
+#define PIN_BUTTON_L2   9           // L2 / LT / ZL / L2 / 7 / K4
+#define PIN_BUTTON_B3   10          // B3 / X / Y / Square / 1 / P1
+#define PIN_BUTTON_B4   11          // B4 / Y / X / Triangle / 4 / P2
+#define PIN_BUTTON_R1   12          // R1 / RB / R / R1 / 6 / P3
+#define PIN_BUTTON_L1   13          // L1 / LB / L / L1 / 5 / P4
+#define PIN_BUTTON_S1   16          // S1 / Back / Minus / Select / 9 / Coin
+#define PIN_BUTTON_S2   17          // S2 / Start / Plus / Start / 10 / Start
+#define PIN_BUTTON_L3   18          // L3 / LS / LS / L3 / 11 / LS
+#define PIN_BUTTON_R3   19          // R3 / RS / RS / R3 / 12 / RS
+#define PIN_BUTTON_A1   20          // A1 / Guide / Home / PS / 13 / ~
+#define PIN_BUTTON_A2   21          // A2 / ~ / Capture / ~ / 14 / ~
+#define PIN_BUTTON_FN   -1          // Hotkey Function
+#define PIN_BUTTON_TURBO 29         // Turbo
+#define PIN_BUTTON_REVERSE -1       // UDLR Reverse
+#define PIN_SLIDER_LS    -1         // Left Stick Slider
+#define PIN_SLIDER_RS    -1         // Right Stick Slider
+#define PIN_SLIDER_SOCD_ONE    -1         // SOCD Slider Pin One
+#define PIN_SLIDER_SOCD_TWO    -1         // SOCD Slider Pin Two
+
+
+// This is the SOCD section.
+// SOCD stands for `simultaneous opposing cardinal directions`.
+// There are three options for `DEFAULT_SOCD_MODE` currently:
+// 1 - `SOCD_MODE_NEUTRAL` - This is a neutral SOCD.  EG. when you press `up` + `down` no input will be registered.
+// 2 - `SOCD_MODE_UP_PRIORITY` - This is up priority SOCD.  EG. when you press `up` + `down` `up` will be registered.
+// 3 - `SOCD_MODE_SECOND_INPUT_PRIORITY` - This is last priority SOCD.  EG. when you press and hold `up` then press `down` `down` will be registered.
+// 4 - `SOCD_MODE_FIRST_INPUT_PRIORITY` - This is first priority SOCD.  EG. when you press and hold `up` then press `down` `up` will be registered.
+
+#define DEFAULT_SOCD_MODE SOCD_MODE_NEUTRAL
+// SOCD Slider Slot Defaults
+#define SLIDER_SOCD_SLOT_ONE SOCD_MODE_UP_PRIORITY
+#define SLIDER_SOCD_SLOT_TWO  SOCD_MODE_SECOND_INPUT_PRIORITY
+#define SLIDER_SOCD_SLOT_DEFAULT SOCD_MODE_NEUTRAL
+
+#define DEFAULT_FORCED_SETUP_MODE FORCED_SETUP_MODE_OFF // 	FORCED_SETUP_MODE_OFF, FORCED_SETUP_MODE_LOCK_MODE_SWITCH, FORCED_SETUP_MODE_LOCK_WEB_CONFIG, FORCED_SETUP_MODE_LOCK_BOTH
+#define DEFAULT_LOCK_HOTKEYS false // or true
+
+// This is the LEDs section.
+// The default `TURBO_LED_PIN` pin is set to `15` ( it is recommended to run through 3V3(OUT) with a resistor)
+// The Turbo LED will flash at a speed consistant with the set speed of the Turbo when a Turbo button is active.
+// It is recommended to disable the `TURBO_LED_PIN` by setting it to `-1` if you are sensitive of flashing lights.
+// The default `BOARD_LEDS_PIN` pin is set to `28`.
+// The board LED pin will allow you to connect addressible RGB LEDs on the Pico.
+// Addressible RGB LEDs should be connected to the `VBUS` pin (#40), an avalible ground pin and the defined `BOARD_LEDS_PIN`.
+// Special note - You should only ever use addressible RGB LEDs that are rated for 5v operation on the Pico.
+// The defualt `LED_BRIGHTNESS_MAXIMUM` value is `50`.
+// This will change how bright the LEDs are with `0` being off and `100` being full brightness.
+// The minimum `LED_BRIGHTNESS_MAXIMUM` value is `0`.
+// The maximum `LED_BRIGHTNESS_MAXIMUM` value is `100`.
+// The defualt `LED_BRIGHTNESS_STEPS` value is `5`.
+// This will change how many brightness steps there are when increasing or decreasing the brightness of the LEDs via the onboard shortcut.
+// It is recommend to keep this value at `5` or `10`.
+// The defualt `LED_FORMAT` is `LED_FORMAT_GRB`.
+// You can also choose the `LED_FORMAT` of `LED_FORMAT_RGB` if your addressible RGB LEDs are not working as intended.
+// The defualt `LEDS_PER_PIXEL` is set to `1`.
+// This will change how many addressible RGB LEDs there are per button.
+// The default LEDS_[BUTTON] is an order and has nothing to do with what GPIO pin something is connected to.
+// Unless you are planning on running custom animations I would recommmend you leave this as is.
+
+#define TURBO_LED_PIN -1
+
+#define LED_BRIGHTNESS_MAXIMUM 150
+#define LED_BRIGHTNESS_STEPS 5
+#define LED_FORMAT LED_FORMAT_GRB
+#define LEDS_PER_PIXEL 1
+
+#define LEDS_DPAD_LEFT   11
+#define LEDS_DPAD_DOWN   10
+#define LEDS_DPAD_RIGHT  9
+#define LEDS_DPAD_UP     0
+#define LEDS_BUTTON_B3   8
+#define LEDS_BUTTON_B4   7
+#define LEDS_BUTTON_R1   6
+#define LEDS_BUTTON_L1   5
+#define LEDS_BUTTON_B1   1
+#define LEDS_BUTTON_B2   2
+#define LEDS_BUTTON_R2   3
+#define LEDS_BUTTON_L2   4
+#define LEDS_BUTTON_S1   -1
+#define LEDS_BUTTON_S2   -1
+#define LEDS_BUTTON_L3   -1
+#define LEDS_BUTTON_R3   -1
+#define LEDS_BUTTON_A1   -1
+#define LEDS_BUTTON_A2   -1
+
+
+// This is the Player LED section.
+// In this section you can specify if Player LEDs will be active, and, if active, which pins will be used for them.
+// The defualt is `PLED_TYPE_NONE` which will turn the Player LEDs off.
+// The default pin for each Player LED is `-1` which disables it.
+// To enable a `PLED#_PIN`, replace the `-1` with the GPIO pin number that is desired.
+// There are three options for `PLED_TYPE` currently:
+// 1 - `PLED_TYPE_NONE` - This will disable the Player LEDs
+// 2 - `PLED_TYPE_PWM` - This will enable the Player LEDs ( it is recommended to run through 3V3(OUT) with a resistor)
+// 3 - `PLED_TYPE_RGB` - This will enable the Player LEDs as addressible RGB LEDs (please not that this has not been implemented yet)
+
+#define PLED_TYPE PLED_TYPE_NONE
+#define PLED1_PIN 16
+#define PLED2_PIN 17
+#define PLED3_PIN 18
+#define PLED4_PIN 19
+
+
+// This is the Analog section.
+// In this section you can specify if Analog is enabled, and, if endabled, which pins will be used for it.
+// The default for `ANALOG_ADC_VRX` and `ANALOG_ADC_VRY` is `-1` which disables them.
+// To enable a `ANALOG_ADC_VRX` and `ANALOG_ADC_VRY`, replace the `-1` with the GPIO pin numbers that are desired. 
+
+#define ANALOG_ADC_1_VRX -1
+#define ANALOG_ADC_1_VRY -1
+#define ANALOG_ADC_1_MODE DPAD_MODE_LEFT_ANALOG
+#define ANALOG_ADC_1_INVERT INVERT_NONE
+
+#define ANALOG_ADC_2_VRX -1
+#define ANALOG_ADC_2_VRY -1
+#define ANALOG_ADC_2_MODE DPAD_MODE_RIGHT_ANALOG
+#define ANALOG_ADC_2_INVERT INVERT_NONE
+
+
+// This is the I2C Display section (commonly known as the OLED display section).
+// In this section you can specify if a display as been enabled, which pins are assined to it, the block address and speed.
+// The default for `HAS_I2C_DISPLAY` is `1` which enables it.
+// To disable the display you can change `HAS_I2C_DISPLAY` to `-1`.
+// The default `I2C_SDA_PIN` is `0`.
+// The defualt `I2C_SCL_PIN` is `1`.
+// The defualt `I2C_BLOCK` is `12c0`.
+// If you change the `I2C_SDA_PIN` and `I2C_SCL_PIN` pin mapping, you may need to change the `I2C_BLOCK` as well.
+// The defualt `I2C_SPEED` is `400000`.
+// This should be more than fast enough for most displays.
+// Some smaller displays (like 0.96" and 1.31") can go up to `800000` or even `1000000`.
+// The default `DISPLAY_FLIP` is `0`.
+// This can be changed to `1` to have the dispaly output flipped.
+// The default `DISPLAY_INVERY` is `0`.
+// This can be changed to `1` to have the color on the display inverted.
+// The default `BUTTON_LAYOUT` is `BUTTON_LAYOUT_STICK` which will show an arcade stick on the left hand side of the display.
+// There are seven options for `BUTTON_LAYOUT` currently:
+// 1 - BUTTON_LAYOUT_STICK - This is a basic joystick layout
+// 2 - BUTTON_LAYOUT_STICKLESS - This is a basic stickless (all button) layout
+// 3 - BUTTON_LAYOUT_BUTTONS_ANGLED - This a WASD button layout that is angled
+// 4 - BUTTON_LAYOUT_BUTTONS_BASIC - This a WASD button layout that is straight
+// 5 - BUTTON_LAYOUT_KEYBOARD_ANGLED - This is a WASD keyboard layout that is angled
+// 6 - BUTTON_LAYOUT_KEYBOARDA - This is a WASD keyboard layout that is straight
+// 7 - BUTTON_LAYOUT_DANCEPADA - This is a dance pad layout (must be used with `BUTTON_LAYOUT_DANCEPADB` in `BUTTON_LAYOUT_RIGHT`)
+// The default `BUTTON_LAYOUT_RIGHT` is `BUTTON_LAYOUT_NOIR8` which will show eight buttons on the right hand side of the display.
+// There are eleven options for `BUTTON_LAYOUT_RIGHT` currently:
+// 1 - BUTTON_LAYOUT_ARCADE - This is a standard 8 button arcade layout
+// 2 - BUTTON_LAYOUT_STICKLESSB - This is a basic stickless (all button) layout
+// 3 - BUTTON_LAYOUT_BUTTONS_ANGLEDB - This is a standard 8 button arcade layout that is angled
+// 4 - BUTTON_LAYOUT_VEWLIX - This is the standard 8 button Vewlix layout
+// 5 - BUTTON_LAYOUT_VEWLIX7 - This is the standard 7 button Vewlix layout
+// 6 - BUTTON_LAYOUT_CAPCOM - This is the standard 8 button Capcom layout
+// 7 - BUTTON_LAYOUT_CAPCOM6 - This is the stndard 6 button Capcom layout
+// 8 - BUTTON_LAYOUT_SEGA2P - This is the standard 8 button Sega2P layout
+// 9 - BUTTON_LAYOUT_NOIR8 - This is the standard 8 button Noir layout
+// 10 - BUTTON_LAYOUT_KEYBOARDB - This is a WASD keyboard layout that is straight
+// 11 - BUTTON_LAYOUT_DANCEPADB - This is a dance pad layout (must be used with `BUTTON_LAYOUT_DANCEPADA` in `BUTTON_LAYOUT`)
+// The default `SPLASH_MODE` is `NOSPLASH`.
+// There are four options for `SPLASH_MODE` currently:
+// 1 - `STATICSPLASH` - This will display the static splash image
+// 2 - `CLOSEIN` - This will display the static splash image as a top and bottom coming together animation
+// 3 - `CLOSEINCUSTOM` - This will display the custom splash image as a top and bottom coming together animation
+// 4 - `NOSPLASH` - This will not display a splash screen on boot
+// Special note - All of the splash screen images can be changed via `include/bitmaps.h`
+
+#define HAS_I2C_DISPLAY 1
+#define I2C_SDA_PIN 0
+#define I2C_SCL_PIN 1
+#define I2C_BLOCK i2c1
+#define I2C_SPEED 400000
+#define DISPLAY_FLIP 0
+#define DISPLAY_INVERT 0
+
+// I2C Analog ADS1219 Add-on Options
+#define I2C_ANALOG1219_SDA_PIN -1
+#define I2C_ANALOG1219_SCL_PIN -1
+#define I2C_ANALOG1219_BLOCK i2c0
+#define I2C_ANALOG1219_SPEED 400000
+#define I2C_ANALOG1219_ADDRESS 0x40
+
+// Reverse Button section
+#define REVERSE_LED_PIN -1
+#define REVERSE_UP_DEFAULT 1
+#define REVERSE_DOWN_DEFAULT 1
+#define REVERSE_LEFT_DEFAULT 1
+#define REVERSE_RIGHT_DEFAULT 1
+
+#define BUTTON_LAYOUT BUTTON_LAYOUT_STICKLESS
+#define BUTTON_LAYOUT_RIGHT BUTTON_LAYOUT_STICKLESSB
+#define SPLASH_MODE SPLASH_MODE_NONE
+#define SPLASH_CHOICE SPLASH_CHOICE_MAIN
+#define SPLASH_DURATION 7500 // Duration in milliseconds
+
+// Board LED Add-on Setting
+// BOARD_LED_OFF  - Turns the on-board LED off
+// MODE_INDICATOR - On-board LED blinks on various frequencies depending
+//                  on the current mode (config, normal, or no USB data)
+// INPUT_TEST     - Blinks whenever any input is made
+
+#define BOARD_LED_ENABLED 1
+#define BOARD_LED_TYPE ON_BOARD_LED_MODE_PS_AUTH
+
+// Dual Directional Add-on Options
+
+#define PIN_DUAL_DIRECTIONAL_UP -1
+#define PIN_DUAL_DIRECTIONAL_DOWN -1
+#define PIN_DUAL_DIRECTIONAL_LEFT -1
+#define PIN_DUAL_DIRECTIONAL_RIGHT -1
+#define DUAL_DIRECTIONAL_STICK_MODE DPAD_MODE_DIGITAL
+#define DUAL_DIRECTIONAL_COMBINE_MODE DUAL_COMBINE_MODE_MIXED
+
+// BOOTSEL Button Add-on setting
+#define BOOTSEL_BUTTON_MASK 0 // 0 means none, get other mask from GamepadState.h
+
+// Extra Button Add-on setting
+#define EXTRA_BUTTON_MASK 0 // 0 means none, get other mask from GamepadState.h
+                            // For directions, use GAMEPAD_MASK_DU, GAMEPAD_MASK_DD, GAMEPAD_MASK_DL and GAMEPAD_MASK_DR
+#define EXTRA_BUTTON_PIN -1
+
+// Keyboard Mapping Configuration
+// List of HID keycodes can be located here: https://github.com/hathach/tinyusb/blob/3623ba1884ddff23e9b64766cb6dd032f1425846/src/class/hid/hid.h#L356
+// Even for the modifier keys, HID_KEY entries should be used as the implementation expects those and will convert as necessary.
+#define KEY_DPAD_UP     HID_KEY_ARROW_UP      // UP
+#define KEY_DPAD_DOWN   HID_KEY_ARROW_DOWN    // DOWN
+#define KEY_DPAD_RIGHT  HID_KEY_ARROW_RIGHT   // RIGHT
+#define KEY_DPAD_LEFT   HID_KEY_ARROW_LEFT    // LEFT
+#define KEY_BUTTON_B1   HID_KEY_SHIFT_LEFT    // B1 / A / B / Cross / 2 / K1
+#define KEY_BUTTON_B2   HID_KEY_Z             // B2 / B / A / Circle / 3 / K2
+#define KEY_BUTTON_R2   HID_KEY_X             // R2 / RT / ZR / R2 / 8 / K3
+#define KEY_BUTTON_L2   HID_KEY_V             // L2 / LT / ZL / L2 / 7 / K4
+#define KEY_BUTTON_B3   HID_KEY_CONTROL_LEFT  // B3 / X / Y / Square / 1 / P1
+#define KEY_BUTTON_B4   HID_KEY_ALT_LEFT      // B4 / Y / X / Triangle / 4 / P2
+#define KEY_BUTTON_R1   HID_KEY_SPACE         // R1 / RB / R / R1 / 6 / P3
+#define KEY_BUTTON_L1   HID_KEY_C             // L1 / LB / L / L1 / 5 / P4
+#define KEY_BUTTON_S1   HID_KEY_5             // S1 / Back / Minus / Select / 9 / Coin
+#define KEY_BUTTON_S2   HID_KEY_1             // S2 / Start / Plus / Start / 10 / Start
+#define KEY_BUTTON_L3   HID_KEY_EQUAL         // L3 / LS / LS / L3 / 11 / LS
+#define KEY_BUTTON_R3   HID_KEY_MINUS         // R3 / RS / RS / R3 / 12 / RS
+#define KEY_BUTTON_A1   HID_KEY_9             // A1 / Guide / Home / PS / 13 / ~
+#define KEY_BUTTON_A2   HID_KEY_F2            // A2 / ~ / Capture / ~ / 14 / ~
+
+#endif